behringer B-1, B-1 Dark Edition Single Diaphragm Condenser Microphone User Manual
- July 5, 2024
- Behringer
Table of Contents
Behringer B-1, B-1 Dark Edition Single Diaphragm Condenser Microphone
Specifications
- Product Name: B-1 / B-1 Dark Edition
- Type: Single Diaphragm Condenser Microphone
- Large-Diaphragm Studio Condenser Microphone
- Phantom Power Supply: +48V
- Directivity: Cardioid
- Low-Cut Filter: Yes
- Level Attenuator: -10dB
- Frequency Response: 20Hz – 20kHz
Product Usage Instructions
Power Supply
- Your condenser mic B-1 requires a +48V phantom power supply.
- Always mute the sound reinforcement system before switching on the phantom power supply. Allow the B-1 about 6 seconds to stabilize after powering up.
Directivity, Low-Cut Filter, and Level Attenuation
- The cardioid capsule of the B-1 is ideal for directional recording of instruments or vocals. Activate the low-cut filter to filter low-frequency interference and use the -10dB level attenuator for high sound pressure sources.
Mounting Microphone and Elastic Suspension
- Attach the elastic suspension to the microphone stand and insert the B-1 into it. Ensure proper positioning and security with the screw.
Audio Connection/Level Setting
- Use a balanced XLR microphone cable with the correct pin assignment. The B-1 features gold-plated contact points, so use cables with gold-plated connectors for optimal performance.
Safety Instructions
- Read and follow all instructions.
- Avoid water exposure, except for outdoor products.
- Clean with a dry cloth.
- Do not block ventilation openings.
- Avoid heat sources.
- Use only manufacturer-specified attachments/accessories.
FAQ
What type of power supply does the B-1 microphone require?
The B-1 microphone requires a +48V phantom power supply for operation.
How do I activate the low-cut filter on the B-1 microphone?
You can activate the low-cut filter by switching it on from the front panel of the microphone.
What is the recommended cable type for connecting the B-1 microphone?
It is recommended to use a balanced XLR microphone cable with gold-plated connectors for optimal performance with the B-1 microphone.
Safety Instruction
- Please read and follow all instructions.
- Keep the apparatus away from water, except for outdoor products.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install under the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Use only attachments/accessories specified by the manufacturer.
- Use only specified carts, stands, tripods, brackets, or tables. Use caution to prevent tip-overs when moving the cart/apparatus combination.
- Avoid installing in confined spaces like bookcases.
- Do not place naked flame sources, such as lighted candles.
- Operating temperature range 5° to 45°C (41° to 113°F).
Power Supply
Your condenser mic B-1 needs a +48-V phantom power supply. Behringer assumes no liability for any damage caused by a defective phantom power supply. Always mute the sound reinforcement system before you switch on the phantom power supply. After power-up, the B-1 needs about 6 seconds to stabilize.
Directivity, Low-Cut Filter and Level Attenuation
- The capsule used in the B-1 with cardioid characteristics is ideal for the directional recording of instruments or individual vocals.
- Cardioid characteristics represent the most frequently used polar pattern in recording situations.
- With this, unwanted sound in the reverse phase is not picked up.
- The low-cut filter can be activated with the switch on the front (position: left), to filter low-frequency interference such as pop sounds, etc.
- With the low-cut filter on, the B-1 provides an almost linear frequency response with signals picked up in proximity to the source. The built-in shielding minimizes the microphone’s sensitivity to high-frequency interference.
- Use the same switch to activate the -10 dB level attenuator (position: right), which should be used with “pulse-type” signal sources producing high sound pressure levels (e.g. kick drum).
- With the switch set to its center position, both functions are disabled.
Mounting Microphone and Elastic Suspension
- Attach the enclosed elastic suspension to the microphone stand. Fasten the screw, once the suspension has been positioned properly. Open the elastic suspension by pressing the two circular levers, then insert the B-1 from above.
Audio Connection/Level Setting
- Use a balanced XLR microphone cable with the following pin assignment: pin 1 = shielding; pin 2 = +; pin 3 = -.
- Since your B-1 features gold-plated contact points throughout, we recommend that you use only microphone cables with gold-plated connectors.
- Adjust the gain control in the microphone channel of your mixing console so that the peak LED lights up only occasionally or never at all.
- The EQ controls in the microphone channel should be set to mid-travel position to start with; the low-cut filter and level attenuator should be off. Try to achieve the desired sound by experimenting with the microphone position.
- Often, it will be useful to set up acoustic barriers (“gobos”) at various angles towards the signal source.
- Only when the desired basic sound has been achieved, should you start to use equalizers and signal processors, if any at all (Remember: less is often more!)
- The B-1 provides a level peak around 12 kHz producing some kind of “presence” in this range; so, there is no need for high-frequency EQing which could deteriorate the signal and raise the overall noise floor.
- On the contrary, the B-1 provides that much-desired transparency which often gets lost during recording and mixing.
Frequency Response Curve
Polar Pattern
Specifications
- Transducer type condenser, 1″ single diaphragm
- Operating principle pressure gradient
- Polar pattern cardioid
- Connection gold-plated balanced XLR connector
- Open circuit voltage at 1 kHz -34 +/-2 dBV (0 dBV = 1 V/Pa)
- Open circuit sensitivity 20 mV/Pa
- Frequency range 20 Hz – 20 kHz
- Level attenuation -10 dB (switchable)
- Low-cut filter 6 dB/Octave at 75 Hz (switchable)
- Max. SPL (1% THD @ 1 kHz) 138 dB (0 dB), 148 dB (-10 dB)
- Equivalent SPL (IEC 268-4) 13 dB-A
- Signal-to-noise ratio re 1 Pa 81 dB A-weighted
- Nominal impedance 50 Ω
- Load impedance > 1 kΩ
Mains Voltage/Fuse
- Supply voltage +48 V
- Supply current 3 mA
Physical/Weight
- Dimensions 0: 58 mm, length: 174 mm
- Weight 0,461 kg
- Behringer is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice.
- Specifications and appearance may differ from those listed or illustrated.
LEGAL DISCLAIMER
- Music Tribe accepts no liability for any loss that may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein.
- Technical specifications, appearances, and other information are subject to change without notice.
- All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera,
- Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd.
- © Music Tribe Global Brands Ltd. 2024 All rights reserved.
LIMITED WARRANTY
- For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at community.musictribe.com/support.
- Hereby, Music Tribe declares that this product complies with General Product Safety Regulation (EU) 2023/988, Directive 2014/30/EU,
- Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.
- Full text of EU DoC is available at https://community.musictribe.com/
- EU Representative: Music Tribe Brands DK A/S
- Address: Gammel Strand 44, DK-1202 København K, Denmark
- UK Representative: Music Tribe Brands UK Ltd.
- Address: 8th Floor, 20 Farringdon Street London EC4A 4AB, United Kingdom
- Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law.
- This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE).
- The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE.
- At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources.
- For more information about where you can take your waste equipment for recycling, please contact your local city office or your household waste collection service.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>