J-XING F620-161 Wireless Solar Driveway Sensor User Manual
- July 4, 2024
- J-XING
Table of Contents
Wireless Solar Driveway Sensor
F620-161 Instruction
Overview
- The signal transmission for the solar orveway sensor and Ine wireless receNer Can reach 3280 feel, The induction distance of Ihe sclar driveway sensor can be up ta 50 feet, end the induction angle is 120°.
- The induction angie is 30° after instatling the shielding case.
- When the movement of people and vehicies is detected in the monitoring area, the wireless receiver will ring and flash immediaiely.
- Please fully charge the solar criveway sensor before use.
Package
Product specification
1. Solar Driveway Sonsor
PIR Sensor Area/Charge Indicator Light
Function description
“OFF: Power off ; “LOW’: Low sensitivity mode ; “HI”: High sensitiviy mode
*S1-S4 Zone”: S1-S2-S3-S4 sensing zone
PIR Sensor Area: Sensing moving people, animats or vehicles
Charge indicator Light: Light up to remind charging
Solar Panel: Solar charging
Micro USB charging Instruction :
-
The sensor flashes red fight every 1 second when charging, and the sensor lights up red when fully charged.(When the Micro USB is plugged into the sockel, the driveway sensor stops sensing detection unt the Migp‘USB ts unplugged.) ‘
-
When the miOMiisener driveway sensor senses people or moving venicies, the sensor flashes rave) sensor.
-
Wireless Solar dviveway sensor with low battery reminder function.
Sensor low battery reminder:
Sensor battery power 5 20%, the red LED indicator light will flash once every 3 seconds interval.
Sensor battery power ≤ 10%, the red LED indicator light will flash once every 0.5 seconds interval. -
About 3.5 h0urs to full charge by Micro USB charging.
Wireless digital display receiver end reminder:
1. Sensor battery power 5 20%, the receiver sounds ding- – – ding- – – and display the number.
2. Sensor battery power 5 10%. the receiver sounds ding – ding – and display the number.
2. Wirless Receiver
Volume: 4 levels control (0-30-70-110dB )
Melody: 36 ringtones
Learning Code: wireless driveway sensor and wireless receiver paring (Also
switch to mute or nng)
Learning Code: (short presp twice): turn on / off the night light
Operation instructions
Before pairing, please make sure the remaining sensors that no need to be paired are off of away from the paired area.(Note: No sensing and pairing while USB is charging.)
- Switch the wireless driveway sensor to ‘LOW or ‘HI’ mode, and the sensor enter into the power on mode.
- Adjust the ” ” of receiver to select ringtone
- Press and hold the button of the wireless receiver, and trigger the driveway sensor by hand for induction. When you hear the ring of the wireless receiver, first trigger the driveway sensor to observe whether the receiver rings, which means that the pairing is successful. II there is no ring, you can pair again according to the instructions.
- The product has been paired before leaves factory and can be used directly. If you need to pair more sensors, please follow above instructions.
Note: long press button of the receiver for more than 15 seconds will clear all the paired sensors
” S1 – S4″ zone independent ringtone pairing: When switch to zone S1,choose
ringtone A of the receiver then pair with driveway sensor. Alter pairing and
trigger the sensor, the receiver will ring ringtone A.
When switch to zone S2. choose ringtone B of the receiver then pair with
driveway sensor. After pairing and tngger the sensor, the receiver will ring
ringtone B.
Following the above instructions
settings, you can independently pair with different ringtones for the “S1-S4”
zone.
Shielding case installation:
- The shielding case can be installed in the sensing area of the wireless driveway sensor to reduce the sensing angle on both sides of the sensor.
- The shielding case can be detachable with a flat-head screwdriver to pry up concave position on the both sides.
Note: The actual induction distance and angle will vary depending on the operating environment. Please decide to whether install the shielding case according to the scenario usage scenarios.
Wireless driveway sensor installation
When the monitoring object is person, it is better to install 5 to 10 feet
away from the ground and adjust the angle of the sensor. When the monitoring
object is vehicle, it is better to install the sensor at a distance of 0-30
feet from the road and 3-5 feet from the ground and adjust the angle of the
sensor. After choosing the best position according to the operating
environment, fix the bracket with screws according to the position of the
screw hole, and then face up the solar photovoltaic panel of the sensor and
adjust the sensor angle.
Wireless driveway sensor installation precautions
- Plase install the sensor in a fixed area, old the installation position in which is shaken or shaken by wind.
- Please face the sensor towards an open area, Do nal face the sensor towards the area where there are frequent object movements,(e.g.trees. crowds)
Product parameters
Solar Driveway Sensor
Size| 43 3.15 inch
Charging Voltage| DC 5V1A
Battery Capacity| 3,7V 1200mAH
USB Charging Time| 54 hours
Working Current| 5 100mA
Working Time| About 45 days
Solar Panel Current| 50mA
Detection Distance| Low ≤26 feet Hi ≤ 50 feet (Detection distance varies by
ambient temperature and other factors)
Detection Angle| ≤ 120″
Detection Angle with Shielding Case| ≤ 30″
Transmission Frequency| 433.92MHZ±200KHZ
Transmission Distance| ≤ 3000 feet
Waterproof Rating| IP 65
Wireless Receiver
| Size | 3.53.51.61 inch |
|---|---|
| Charging Voltage | DC 5V1A |
| Battery Capacity | 3.7V 1000mAH |
| Melody | 36 tingtones |
| Volume | 0-30-70-110d8 |
| Receivers Frequency | 433.92MHZ±200KHZ |
| Received Distance | ≤ 3000 feet |
Troubleshooting
Receiver dose not work| 1.Check whether if the wireless driveway sensor and
wireless receiver match successtully.
2.Check whether if the wireless driveway sensor switch is power on.
3, Check whether if the wireless driveway sensor is low battery.
4.Check whether if the induction area of the wireless driveway is aligned with
the desired detection range.
---|---
Receiver flash ring| 1. Check if there are high frequency products nearby.
(0.9. WIFI, power station, etc.)
2. Try to reduce the angle of shield to reduce the sensing ares.
FCC Caution.
§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>