Stealth Products P116D739 Back Support Hardware Owner’s Manual
- July 2, 2024
- Stealth Products
Table of Contents
Backs and Support
Quick Release PRO
Owner’s Manual – Maintenance Guide
Quick Release PRO Back Support Hardware
Customer Satisfaction
Stealth Products is committed to 100% customer satisfaction. Your complete
satisfaction is important to us. Please contact us with feedback or
suggestions to help us improve the quality and usability of our products.
You may reach us at:
StealthProducts,LLC
104 JohnKellyDrive,Burnet,TX78611
Phone:(512)715-9995
Fax:(512)715-9954
Toll Free:(800)965-9229
Toll Free:(800)806-1225
info@stealthproducts.com
www.stealthproducts.com
MDSS GmbH
Schiffgraben 4130175 Hannover Germany|
SODIMED SA
Chemin Praz Devant 121032Romanel sur-Lausanne Switzerland|
UKAuthorizedRepresentative
MDSS-UK RP
6 Wilmslow Road,Rusholme Manchester M14 5TP United Kingdom
---|---|---
General
Read and understand all instructions prior to the use of the product.
Failure to adhere to instructions and warnings in this document may result in
property damage, injury, or death. Product misuse or failure to follow
instructions will void the warranty.
Immediately discontinue use if any function is compromised, if parts are
missing or loose, or if any component shows signs of excessive wear. Consult
with your supplier for repair, adjustment, or replacement.
All persons responsible for fitting, adjustment, and daily use of the devices
discussed in these instructions must be familiar with and understand all
safety aspects of the devices mentioned. In order for our products to be used
successfully, you must read and
understand all instructions and warnings, and maintain our products according
to our instructions on care and maintenance.
The installation instructions will guide you through this product’s options
and possibilities.
Instructions are written with the expressed intent of use with standard
configurations. They also contain important safety and maintenance
information, as well as describe possible problems that can arise during use.
For further assistance, or more advanced applications, please contact your
supplier or Stealth Products at
512-715-9995 or toll free at (800)
9659229.
Always keep the operating instructions in a safe place so they may be
referenced as necessary.
All information, pictures, illustrations, and specifications are based on the
product information that was available at the time of printing. Pictures and
illustrations shown in these instructions are representative examples and are
not intended to be exact depictions of the various parts of the product.
Important Information
CAUTION
These products are designed to be fitted, applied, and installed
exclusively by a healthcare professional trained for these purposes. The
fitting, application, and installation by a non-qualified individual could
result in serious injury.
Warranty
Our products are designed, manufactured, and produced to the highest of
standards. If any defect in material or workmanship is found, Stealth Products
will repair or replace the product at our discretion. Any implied warranty,
including the implied warranties of merchantability and fitness for a
particular purpose, shall not extend beyond the duration of this warranty.
Stealth Products does not warrant damage due to, but not limited to: Misuse,
abuse, or misapplication of product, and/or modification of product without
written approval from Stealth Products, LLC. Any alteration or lack of serial
number, where applicable, will automatically void all warranty.
Stealth Products, LLC Is liable for replacement parts only. Stealth Products,
LLC is not liable for any incurred labor costs.
Stealth Products warrants against failure due to defective materials or
workmanship:
Covers: 2 years
Hardware: 5 years
Electronics: 3 years
In the event of a product failure covered by our warranty, please follow the
procedures outlined below:
Call Stealth Products at 512-715-9995
or toll free at 800-965-9229.
Request a Return Authorization (RA) form from the Returns Department and
follow the documentation instructions.
You can download additional copies of this manual by accessing the Stealth
website (www.stlpro.site/stealth-docs)
and searching “Quick Release PRO” in the search bar at the top of the page.
Supplier Reference
Supplier:|
---|---
Telephone:|
Address:|
|
Purchase Date:|
Model:|
Warning Labels
Warnings are included for the safety of the user, client, operator, and
property. Please read and understand what the signal words DANGER, WARNING,
CAUTION, NOTICE, and SAFETY mean, and how they could affect the user, those
around the user, and property.
DANGER
Identifies an imminent situation which, if not avoided, may result in severe
injury, death, and property damage.
WARNING
Identifies a potential situation which, if not avoided, may result in severe
injury, death, and property damage.
CAUTION
Identifies a potential situation which, if not avoided, may result in minor to
moderate injury and property damage.
NOTICE
Identifies important information not related to injury, but possible property
damage.
SAFETY
Indicates steps or instructions for safe practices, reminders of safe
procedures, or important safety equipment that may be necessary.
Limited Liability
Stealth Products, LLC accepts no liability for personal injury or damage to
property that may arise from the failure of the user or other persons to
follow the recommendations, warnings, and instructions in this manual.
Stealth Products does not hold responsibility for final integration of final
assembly of product to end user. Stealth Products is not liable for user death
or injury.
Testing
Initial setup and driving should be done in an open area free of obstacles
until the user is fully capable of driving safely.
Design and Function
Intended Use
ADI’s Quick Release mounting hardware is designed to allow wheelchair users
and assistants the ability to easily remove the back support with one hand. In
addition, the Quick Release mounting hardware offers angle, depth, and width
adjustability.
Parts Included
| Description| Qty| Torque
---|---|---|---
A| M5 x 0.8 x 22MM SHS N| 2| 10.3 N·m
B| M6 x 1.0 x 8MM CPSS N| 1| N/A
C| M5 FW| 2| –
D| QR PRO OUTSIDE CLAMP| 1| –
E| M6 x 1.0 x 25MM SHS N| 3| 17.5 N·m
F| QR PRO INSIDE CLAMP| 1| –
G| LATCH PLATE ASSEMBLY| 1| –
H| BR5034, CLAMP NUT| 1| –
I| QR PRO MAIN PLATE| 1| –
J| QR PRO NUT| 1| –
K| QR PRO SHORT PIN*| 2| –
L| M6 x 1.0 NLN| 2| 17.5 N·m
M| QR PRO 45º ATTACHMENT BRACKET| 1| –
N| M6 x 1.0 NLN| 2| 17.5 N·m
O| BR5011-1| 1| –
- Illustration shows short pins in installation positions. Medium and Long Pins are included in the package and are shown above for illustration purposes.
Tools Required
3mm Hex Key
4mm Hex Key
5mm Hex Key
10mm socket, crescent or open end wrench
11mm socket, crescent or open end wrench Pin Size Selection
The hardware contains three sizes of pin: short, medium, and long. One of
these is chosen, based on the width of the wheelchair and the back support
shell, and is installed on the bracket that attaches to the back support
shell. Selection of the proper pin allows the hardware to accommodate more
variations in back shell and wheelchair width.
Installing Pin to Bracket
The QR Pro Short Pin (K) is installed to the QR Pro Attachment Bracket (M) by
inserting it into the desired location on the bracket and securing it with an
M6 x 1.0 Nylon Lock Nut (N). There are two holes in the bracket for each pin,
allowing a depth or angle adjustment to be made with the bracket.
To install the pin:
- Place the pin in the desired upper hole in the bracket as shown in the illustration to the right.
- Thread the Nylon Lock Nut onto the pin.
- Hold the flat sides of the pin (as shown above) with an 11mm open end or crescent wrench to keep it from rotating and use a 10mm wrench to tighten the Nylon Lock Nut to the torque specification listed on Page 1.
- Repeat these steps to install the lower pin.
Installation Instructions
Mounting Bracket to Back Shell
To mount the bracket to the back shell:
- The slot in the QR PRO 45º Attachment Bracket (M) has three positions that can be used to mount it to the back shell. Choose the hole that best matches the desired width and align it with the slot in the back shell.
- Insert the BR5011-1 (O) through the slot in the back shell and through the hole chosen in Step 1.
- Thread an M6 x 1.0 NLN (L) on each of the studs and use a 10mm wrench to secure the bracket at the proper height on the back shell.
- Tighten the nylon lock nuts to the torque specification listed on Page 1 with a 10mm wrench.
Mounting Receiver to Cane
To mount the receiver to the Cane:
- Using a 4mm hex wrench, loosen the two M5 x 0.8 x 22mm SHS N (A)* until the QR PRO Outside Clamp (D) will fit over the cane, but do not remove the screws.
- Note: Make sure the Set Screw is not protruding past the inside surface of the Outside Clamp prior to installation on the cane.
- Slide the wheelchair cane between the QR PRO Outside Clamp (D) and the QR PRO Inside Clamp (F). * If installing on 3/4″ or 7/8″ canes, remove the 22mm Socket Head Screws and replace with the 20mm screws provided. This will eliminate the risk of the screw thread protruding into the removable plate and possibly leading to a malfunction.
- Adjust the mounting hardware for height on the cane, and tighten the two M5 x 0.8 x 22mm Socket Head Screws (A) to secure it in place.
The M6 x 1.0 x 8MM CPSS N (B) in the QR Pro Outside Clamp (D) is designed to maintain alignment of the clamp to the cane. When the final position of the hardware is determined, tighten this set screw to further secure the clamp to the cane.
CAUTION
Do not install the Quick Release PRO hardware on wheelchair canes with a
diameter less than 3/4 inch or greater than 1 inch.
Adjustment Instructions
Height Adjustment
The Quick Release PRO hardware can be adjusted for backrest height in several
ways:
- If the hardware needs to move with respect to the canes, loosen the Set Screws and the two M5 x 0.8 x 22mm Socket Head Screws (A) on both sides of the wheelchair. Grasp the hardware and slide it up or down the canes to the desired position. Align the hardware such that the mounting pins are perpendicular to the main plate, and tighten the M5 x 0.8 x 22mm Socket Head Screws. Snug the Set Screws on both sides to secure the adjustment
- If the back support needs to be raised or lowered, but the clamps are in a good position on the canes, loosen the two Nylon Lock Nuts securing the QR PRO 45º Attachment Brackets (M) to the shell on both sides of the chair. Raise or lower the back support to the new position and tighten the Nylon Lock Nuts to secure it. tooltip
Depth Adjustment
Beyond the half-inch depth adjustment afforded by the two mounting holes in
the brackets for the pins, the QR Pro Main Plate (I) can be positioned fore or
aft a total of four inches.
This means the receiver’s mount point can be in front of, or behind, the axis
of the canes (see illustration below).
NOTE: The Cane Clamp must be rotated in relation to
the Receiver Plate to access this range of adjustment.
CAUTION
Be sure to set the fore/aft position of the Quick Release mounting hardware
properly to avoid compromising the stability of the wheelchair.
Angle Adjustment
To adjust the angle of the hardware:
-
Loosen the three M6 x 1.0 x 25mm Socket tooltip
Head Screws (E) with a 5mm hex wrench on both sides of the wheelchair. -
Adjust the main plate to the desired angle.
-
Tighten the three socket head screws to the torque specification listed on Page 1.
WC20 Transit Informetion
Quick Release Removal and Replacement
The Latch Plate Assembly (G) locks the QR PRO Attachment Bracket (M) and QR
PRO Pins (K) to the QR PRO Main Plate (I).
To unlock and operate the Latch Plate Assembly:
-
This represents the locked position of the hardware.
Before operating the wheelchair, make sure both latch assemblies are locked in this position. -
Rotate the lever away from the body of the main plate to release the latch. The latch is now free to be operated.
-
Lift the latch to release the pin and allow the back support to be removed.
-
Rotate the top pin away from the main plate and latch assembly.
-
Lift the bottom pin from its position and remove the back support from the wheelchair.
CAUTION
Periodically check for loose hardware or fasteners.
Ensure the latch on each side is fully engaged prior to each use.
WC20 Quick Release Hardware
The Quick Release mounting hardware has met WC20 and ISO 16840-4 requirements
and provisions.
WC20 establishes design and performance requirements and test methods for
complete seating systems that consist of a seat, back support, and attachment
hardware.
General Guidelines
- Attach the tie-down straps only to the designated labeled transit security points.
- Tighten the straps sufficiently to remove all slack. Never attach tie-downs to adjustable, moving, or removable parts of the wheelchair.
- Position the anchor points for the rear tie-down straps directly behind the rear securement points on the wheelchair.
- The front tie-down straps should anchor to floor points that are spaced wider than the wheelchair to provide increased lateral stability.
CAUTION
The WC20-approved Quick Release PRO mounting hardware should only be used as
described in the manufacturer’s instructions.
Before Transit
- Clients who use wheelchairs should transfer to the vehicle seat and use the vehicle-installed occupant restraint systems
- Prior to transporting, always double-check the tie-downs and hardware.
- On tie-downs and restraints, look for tears or worn webbing straps. Replace torn or worn webbing straps as necessary.
- Look for damaged hooks or loose tie-down hardware.
- On the seating system, check for loose screws attaching the hardware to the back. Check for loose screws attaching the hardware to the seat. These should be snug and not over-tightened.
DANGER
The WC20-approved Quick Release PRO mounting hardware is designed specifically
for occupancy when used on wheelchairs that are facing forward in motor
vehicles.
Belt Placement
-
The pelvic belt restraint should be worn low, across the front of the pelvis near the junctions of the pelvis and the thighs.
-
The belt restraint buckle of three-point belt restraints should be placed in contact with the occupants body and away from wheelchair components.
-
The junction of the shoulder belt and pelvic belt of three-point-belt restraints should be located near the hip opposite the shoulder over which the diagonal belt crosses and not near the midline of the occupant.
Proper Positioning of Belts on Occupants -
Upper torso belt restraints should fit directly over, and in contact with, the middle of the shoulder.
CAUTION
Belt restraints should be adjusted to fit as snugly as possible, consistent
with user comfort.
SAFETY
Belt restraints should be positioned on the wheelchair occupant in accordance
with WTORS manufacturer instructions.
Belt restraints should not be routed outside of the
wheelchair, over the wheelchair wheels, or over the wheelchair arm supports
and should not be held away from the body by wheelchair components or parts.
SAFETY
Belt restraints should not be worn twisted or in a manner that reduces the
area of contact of the belt webbing with the occupant.
Both pelvic belt and shoulder belt restraints that comply with RESNA
WC-4:2012, Section 18 and/or 4.6, 5.2, 5.3 of RESNA WC-4:2012, Section 19
should be used to limit occupant movement in a crash and reduce the likelihood
of occupant ejection from the vehicle and/or injurious contact of the occupant
with the vehicle interior.
The pelvic belt should be angled between 30° to 75° horizontally when viewed
from the side, and ideally between 45° to 75° horizontally, as shown in the
figure to the right.
WARNING
Back supports with adjustable recline angles should not be tilted back more
than 30° to the vertical during travel in vehicles unless necessary for the
medical and postural needs of the occupant.
WARNING
If the back support must be adjusted to an angle that is greater than 30° to
the vertical during travel, the upper shoulder-belt anchor point should be
adjusted rearward to maintain belt contact with the wheelchair occupant’s
shoulder and chest.
Sufficient forward and rearward clear space should be provided around the
wheelchair occupant.
The forward clear-space (FCZ) needs to be larger when a shoulder-belt
restraint is not used.
DANGER
The WC20-approved Quick Release PRO mounting hardware is designed ONLY for use
with wheelchair frames that have been successfully crash tested to the frontal
impact requirements of RESNA WC-4:2012, Section 19.
DANGER
The WC20-approved Quick Release PRO mounting hardware MUST be used on a
wheelchair frame that provides four securement points and pelvic-belt anchor
points that conform to the requirements of RESNA WC-4:2012, Section 19.
Trays
Wheelchair-mounted rigid trays that are not specifically designed for use
during travel in motor vehicles should be:
- Removed and secured separately in the vehicle.
- Secured to the wheelchair so they will not break free in a crash.
- Positioned with a gap of at least 3 in. (7.6 cm) between the back edge of the tray and the wheelchair occupant’s abdomen and/or chest so as not to interfere with proper belt-restraint use.
- Fitted with energy-absorbent padding between the back edge of the tray and the wheelchair occupant.
User Safety
The use of a postural pelvic belt attached to the wheelchair base or seat
frame is encouraged during travel, but these belts should be positioned so
that they do not interfere with the proper positioning of crash-worthy belt
restraints, and they should not be relied on for occupant protection in crash
situations unless the postural belt has been designed to comply with, and
perform to, the requirements 4.6, 5.2, and 5.3 of RESNA WC-4:2012, Section 19.
DANGER
Alterations or substitutions should not be made to the seating system or its
parts and components without consulting the manufacturer.
DANGER
The WC20-approved Quick Release PRO mounting hardware has been designed to
accommodate the proper use of vehicle-anchored belt restraints and the ratings
of the seating systems with regard to ease of properly positioning vehicle-
anchored belt restraints on the wheelchair passenger, and the degree to which
proper positioning of the belt restraints can be achieved.
First Time Usec
Dealer Assistance
During first time use by the client, it is advised that the dealer or service
technician assists and explains the configuration to the customer (the user
and/or the attendant). If needed, the dealer can make final adjustments.
User Testing
It is important that the customer is fully aware of the installation and how
the product can be adjusted in order to gain the best positioning possible. As
a dealer, proceed as follows:
- Explain and show the client how you have executed the installation, and explain the function.
Have the user test the position of the product:
- Is the Quick Release PRO mounting hardware in the proper position for the client?
- Can the user safely operate the chair in the position in which they are seated?
- Is the placement of the back support and Quick Release PRO mounting hardware in an optimal position for the client?
Conditions of Use
The Quick Release PRO mounting hardware is intended for use as installed by
the dealer, in accordance to the installation instructions in this manual.
- The foreseen conditions of use are communicated by the dealer or service technician to the user and/or attendant during the first time use.
- If the conditions of use change significantly, please contact your dealer or a qualified service technician to avoid excessive wear and tear or unintended damage.
Cleaning and Maintenance
Cleaning
- Use a soft cloth to clean the back shell and mounting hardware.
- Ensure all cleaners are approved for finished steel, aluminum, plastic, and upholstered surfaces.
Maintenance
- Check and tighten all fasteners to the proper torque specifications on a regular basis. Proper torque specifications are located on page 1.
- Repair or replace parts as needed.
SAFETY
Always check all mounting hardware, making sure each fastener is properly
tightened and all latches are locked prior to using the back support.
WARNING
User Weight Limit:
300 lbs. (136.08 kg)
| |
---|---|---
https://stlpro.site/returns-n-warranty| https://stlpro.site/|
https://stlpro.site/stealth-docs/?searchDocument=P116D739
Stealth Products, LLC
info@stealthproducts.com
www.stealthproducts.com
800-965-9229
512-715-9995
104 John Kelly Drive, Burnet, TX 78611
© 2023, Stealth Products, LLC
P116D739R2
Apr 19, 2024
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>