WNC VMC-QSA515M Automotive Grade LTE Module User Manual
- June 28, 2024
- WNC
Table of Contents
VMC-QSA515M Automotive Grade LTE Module
“`html
Product Specifications:
- Product Model: VMC-QSA515M
- Grade: Automotive
- Module Type: LTE with LGA pins
- Targeted Application: Automotive M2M market (TCU, AMM, tracking
system, etc.)
Product Features:
The VMC-QSA515M is an automotive grade LTE module with LGA pins
designed for various automotive applications in the Machine to
Machine (M2M) market. It is suitable for use in Telematics Control
Units (TCU), Automatic Metering Management (AMM), tracking systems,
and more.
Block Diagram:
The module features a block diagram that illustrates its
internal components and connectivity.
Mechanical Design:
The mechanical design includes detailed information about the
physical structure of the module, including pin configurations and
external views.
RF Transmitter Output Power:
The module’s RF transmitter output power specifications are as
follows:
Frequency Band| Tune-up Power (dBm)| Minimum Output Power (dBm)| Typical
Output Power (dBm)| Maximum Output Power (dBm)
---|---|---|---|---
B2 (1850-1910MHz TX)| –| 20.3| 23| 25.7
B4 (1710-1755MHz TX)| –| 20.3| 23| 25.7
B5 (824-849MHz TX)| –| 20.3| 23| 25.7
B7 (2500-2570MHz TX)| –| 20.3| 23| 25.7
Frequently Asked Questions (FAQ):
Q: Can the VMC-QSA515M module be used in consumer-grade
applications?
A: No, the VMC-QSA515M module is specifically designed for
automotive applications in the M2M market and may not be suitable
for consumer-grade use.
Q: What is the retention period for the user manual and related
documents?
A: The retention period for the user manual and related
documents is until the next release, as indicated by the document
author.
“`
4 Addition of Document Subject:
VMC-QSA515M User Manual
VMC-QSA515M NA User Manual
Alteration of Document Doc. No.:
Revocation of Document Rev: 0.9 Page 1 of 13
VMC-QSA515M NA User Manual
ALL RIGHTS RESERVED This is an unpublished work. No part of this document may be copied, photocopied, reproduced, translated, or reduced to any electronic or machine-readable form without the prior permission of Wistron NeWeb Corps.
Document author: Owner while current:
Retention period:
Allen Shih Claire Hsieh Until Next Release
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JT-00022-03_001
1
4 Addition of Document Subject:
VMC-QSA515M User Manual
VMC-QSA515M NA User Manual
Alteration of Document Doc. No.:
Revocation of Document Rev: 0.9 Page 2 of 13
Revision Revision Date Revised By
Description
0.1
2022/7/28
Allen Shih
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JT-00022-03_001
2
4 Addition of Document Subject:
VMC-QSA515M User Manual
VMC-QSA515M NA User Manual
Alteration of Document Doc. No.:
Revocation of Document Rev: 0.9 Page 3 of 13
1 General features …………………………………………………………………………………………………………………………..4 2 Block diagram ……………………………………………………………………………………………………………………………..4 3 Mechanical design………………………………………………………………………………………………………………………..5 4 RF specification……………………………………………………………………………………………………………………………6 5 Evaluation Kit ……………………………………………………………………………………………………………………………..7 6 WARNING STATEMENT …………………………………………………………………………………………………………10 7 DECLARATION OF CONFORMITY………………………………………………………………………………………..10
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JT-00022-03_001
3
4 Addition of Document Subject:
VMC-QSA515M User Manual
1 General features
VMC-QSA515M NA User Manual
Alteration of Document Doc. No.:
Revocation of Document Rev: 0.9 Page 4 of 13
The VMC-QSA515M is automotive grade LTE module with LGA pins and targeted for automotive application that is the Machine to Machine (M2M) market including TCU (Telematics Control unit), AMM (Automatic Metering Management), tracking system, etc.
2 Block diagram
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JT-00022-03_001
4
4 Addition of Document Subject:
VMC-QSA515M User Manual
3 Mechanical design
VMC-QSA515M NA User Manual
Alteration of Document Doc. No.:
Revocation of Document Rev: 0.9 Page 5 of 13
Pin 1 (AA1)
Figure 1. Top view of SA515M Figure 2. Side view of SA515M (Without pre- tinning)
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JT-00022-03_001
5
4 Addition of Document Subject:
VMC-QSA515M User Manual
VMC-QSA515M NA User Manual
Alteration of Document Doc. No.:
Revocation of Document Rev: 0.9 Page 6 of 13
4 RF specification 4.1 RF Performance The RF transmitter/receiver is fully compliant with the applicable standards. LTE typical sensitivity performance is to combine primary and diversity antennas at 25°C.
4.2 RF Transmitter Output Power
The maximum output power at the NAD antenna port at room temperature:
Tune-up power
Min Typ Max
LTE Max. Output Power
B2 (1850-1910MHz TX)
20.3
23
25.7
B4 (1710-1755MHz TX)
20.3
23
25.7
B5 (824-849MHz TX)
20.3
23
25.7
B7 (2500-2570MHz TX)
20.3
23
25.7
B12 (699-716MHz TX)
20.3
23
25.7
B13 (777-787MHz TX)
20.3
23
25.7
B14(788-798MHz TX)
20.3
23
25.7
B17(704-716MHz TX)
20.3
23
25.7
B25(1850-1915MHz TX)
20.3
23
25.7
B26(814-849MHz TX)
20.3
23
25.7
B41(2469-2690MHz TX)
20.3
23
25.7
B66(1710-1780MHz TX)
20.3
23
25.7
B71(663-698MHz TX)
20.3
23
25.7
UMTS Max. Output Power
B2 (1850-1910MHz Tx) B4 (1710-1755MHz Tx)
20.3
23
25.7
20.3
23
25.7
B5 (824-849MHz Tx)
20.3
23
25.7
5G SA Max. Output Power
n2 (1850-1910MHz TX)
20
23
26
n5 (824-849MHz TX)
20
23
26
n25(1850-1915MHz TX)
20
23
26
n41(2469-2690MHz TX) n41(2469-2690MHz TX) PC2 n66(1710-1780MHz TX) n71 (663-698MHz TX) n77 (3300-4200MHz TX)
20
23
26
22
26
29
20
23
26
20
23
26
19
23
26
n77 (3300-4200MHz TX) PC2
22
26
29
n78(3300-3800MHz TX)
19
23
26
n78(3300-3800MHz TX) PC2
22
26
29
Unit
dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm
dBm dBm dBm
dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JT-00022-03_001
6
4 Addition of Document Subject:
VMC-QSA515M User Manual
VMC-QSA515M NA User Manual
Alteration of Document Doc. No.:
Revocation of Document Rev: 0.9 Page 7 of 13
4.3 RF Receiver Sensitivity
The receiver sensitivity at the NAD antenna port at room temperature: GSM
bands: 3GPP TS 51.010-1 Section 14.2 WCDMA bands: 3GPP TS 34.121-1 Section 6.2
LTE bands: 3GPP TS GPP 36.521 Section 7.3 5G NR bands: 3GPP TS GPP 38.521
Section 7.3 C-V2X bands: 3GPP TS GPP 36.521 Section 7.3G GNSS bands: -162 dBm
(Measured with external GPS LNA (total gain including cable loss: 14 < Gain <
17; NF < 1.5dB). The VMC-QSA515M
design support eLNA by default, it needs to design eLNA on TCU level or active
GPS antenna.)
5 Evaluation Kit
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JT-00022-03_001
7
4 Addition of Document Subject:
VMC-QSA515M User Manual
6 Antenna design trace
VMC-QSA515M NA User Manual
Alteration of Document Doc. No.:
Revocation of Document Rev: 0.9 Page 8 of 13
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JT-00022-03_001
8
4 Addition of Document Subject:
VMC-QSA515M User Manual
VMC-QSA515M NA User Manual
Alteration of Document Doc. No.:
Revocation of Document Rev: 0.9 Page 9 of 13
Antenna connectors: SMA Test procedure: The printed board will be followed
testing procedures as blow: 1. Using the X-ray to check any RF copper trace is
damaged. 2. Using the open/short equipment to make sure trace/ground plan/via
holes are correct. 3. Using “TDR” equipment to make sure the RF trace
impedance is 50 ohm. 4. Using network analyzer to measure dielectric constant
for printed board. 5. Will follow the production test procedure as
above(item#1~4) for each board.
After trace production, please verify all RF trace impedance with a vector
network analyzer and mare sure the trace impedance is with 50+/- 2ohm.
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JT-00022-03_001
9
4 Addition of Document Subject:
VMC-QSA515M User Manual
7 WARNING STATEMENT
VMC-QSA515M NA User Manual
Alteration of Document Doc. No.:
Revocation of Document Rev: 0.9 Page 10 of 13
RF Exposure Information This device has been tested and meets applicable limits for Radio Frequency (RF) exposure. This equipment should be installed and operated to ensure a minimum of 20 cm spacing to any person at all times.
8 DECLARATION OF CONFORMITY
OEM/Integrators Installation Manual
Important Notice to OEM integrators
1. This module is limited to OEM installation ONLY. 2. This module is limited
to installation in mobile or fixed applications, according to Part 2.1091(b).
3. The separate approval is required for all other operating configurations,
including portable configurations with respect to Part 2.1093 and different
antenna configurations 4. For FCC Part 15.31 (h) and (k): The host
manufacturer is responsible for additional testing to verify compliance as a
composite system. When testing the host device for compliance with Part 15
Subpart B, the host manufacturer is required to show compliance with Part 15
Subpart B while the transmitter module(s) are installed and operating. The
modules should be transmitting and the evaluation should confirm that the
module’s intentional emissions are compliant (i.e. fundamental and out of band
emissions). The host manufacturer must verify that there are no additional
unintentional emissions other than what is permitted in Part 15 Subpart B or
emissions are complaint with the transmitter(s) rule(s).
End Product Labeling
When the module is installed in the host device, the FCC ID label must be
visible through a window on the final device or it must be visible when an
access panel, door or cover is easily re-moved. If not, a second label must be
placed on the outside of the final device that contains the following text:
“Contains FCC ID: NKR-VMC-QSA515MNA” “Contains IC: 4441A-QSA515MNA ” The
grantee’s FCC ID/IC ID can be used only when all FCC/IC compliance
requirements are met.
Antenna Installation
(1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, (2) The transmitter module may not be co-located with any
other transmitter or antenna. (3) To comply with FCC/IC regulations limiting
both maximum RF output power and human exposure to RF radiation, the maximum
antenna gain including cable loss in a mobile exposure condition must not
exceed:
Standalone Condition: 4.4 dBi in WCDMA band 2 4.0 dBi in WCDMA band 4 2.0 dBi
in WCDMA band 5 4.4 dBi in LTE band 2
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JT-00022-03_001
1
4 Addition of Document
Subject:
VMC-QSA515M User Manual
4.0 dBi in LTE band 4 2.0 dBi in LTE band 5 2.3 dBi in LTE band 7 2.0 dBi in
LTE band 12 2.3 dBi in LTE band 13 2.3 dBi in LTE band 14 2.0 dBi in LTE band
17 4.4 dBi in LTE band 25 2.0 dBi in LTE band 26 2.3 dBi in LTE band 41 4.0
dBi in LTE band 66 1.3 dBi in LTE band 71 4.4 dBi in 5G NR n2 2.0 dBi in 5G NR
n5 4.4 dBi in 5G NR n25 2.3 dBi in 5G NR n41 PC3 2.3 dBi in 5G NR n41 PC2 4.0
dBi in 5G NR n66 1.3 dBi in 5G NR n71 1.0 dBi in 5G NR n77_PC3 1.0 dBi in 5G
NR n77_PC2 1.0 dBi in 5G NR n78_PC3 1.0 dBi in 5G NR n78_PC2
VMC-QSA515M NA User Manual
Alteration of Document Doc. No.:
Revocation of Document Rev: 0.9 Page 11 of 13
Assuming collocated with an ordinary WLAN transmitter with 5 dBi antenna gain 3.9 dBi in WCDMA band 2 3.6 dBi in WCDMA band 4 1.5 dBi in WCDMA band 5 3.9 dBi in LTE band 2 3.6 dBi in LTE band 4 1.5 dBi in LTE band 5 1.7 dBi in LTE band 7 1.0 dBi in LTE band 12 1.3 dBi in LTE band 13 1.4 dBi in LTE band 14 1.0 dBi in LTE band 17 3.9 dBi in LTE band 25 1.5 dBi in LTE band 26 1.7 dBi in LTE band 41 3.6 dBi in LTE band 66 0.8 dBi in LTE band 71 3.9 dBi in 5G NR n2 1.5 dBi in 5G NR n5 3.9 dBi in 5G NR n25 1.7 dBi in 5G NR n41 PC3 1.7 dBi in 5G NR n41 PC2 3.6 dBi in 5G NR n66
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JT-00022-03_001
1
4 Addition of Document Subject:
VMC-QSA515M User Manual
0.8 dBi in 5G NR n71 1.0 dBi in 5G NR n77_PC3 1.0 dBi in 5G NR n77_PC2 1.0 dBi
in 5G NR n78_PC3 1.0 dBi in 5G NR n78_PC2
VMC-QSA515M NA User Manual
Alteration of Document Doc. No.:
Revocation of Document Rev: 0.9 Page 12 of 13
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/IC authorization is no longer considered valid and the FCC ID/IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC/IC authorization.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module. The end user manual shall include
all required regulatory information/warning as show in this manual.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following
measures: – Reorient or relocate the receiving antenna. – Increase the
separation between the equipment and receiver. – Connect the equipment into an
outlet on a circuit different from that to which the receiver is connected. –
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Industry Canada Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device
may not cause interference. (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique Canada
applicables aux appareils radio exempts de
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JT-00022-03_001
1
4 Addition of Document Subject:
VMC-QSA515M User Manual
VMC-QSA515M NA User Manual
Alteration of Document Doc. No.:
Revocation of Document Rev: 0.9 Page 13 of 13
licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
CAN ICES-3(B)/ NMB-3(B)
Radiation Exposure Statement
This equipment complies with FCC/IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator & your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements FCC/IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JT-00022-03_001
1