URBANESCAPE DC-12 Front Doors Installation Guide

URBANESCAPE DC-12 Front Doors

Specifications :

• Product Name: DC-12 Installation Kit for Jeep JK/JKU Front Doors
• Model: v.051524
• Installation Time: About ten minutes
• Tools Required: Screwdriver with a T30 Torx Driver Bit, 10mm socket wrench with extension

Product Usage Instructions

• Step 1: Remove Existing Parts
  Remove the existing Door Check Strap from the Body Loop Bracket for the driver’s side door.

• Step 2: Replace Bolts
  Using a 10mm socket wrench, remove the bolts holding the Body Loop Bracket and replace them with the provided M6-1.0X40mm Flanged Hex Bolts.

• Step 3: Attach Receiver
  Align the Receiver on top of the Body Loop Bracket and attach them using the provided bolts. Ensure that the Door Check Strap and its Electrical Wiring are routed below the Receiver without pinching.

• Step 4: Install Carrier
  Remove existing bolts using a T30 Torx bit tool and install the Carrier on top of the Door Loop using the provided bolts. Do not pinch the Door Check Strap with the Carrier.

• Step 5: Install Flex Arm
  Align the free end of the Flex Arm with the Receiver’s opening and close the door slowly. The Flex Arm should slide easily into the Receiver with an audible click. Do not force it if it doesn’t align properly.

Care and Maintenance:
The DC-12 requires dry lubrication. Additional lubrication, if needed, should only be pure PTFE lubricants. Avoid using silicone, petroleum-based lubricants, or other products containing chlorinated solvents as they will void the warranty.

FAQ :

• Q: What is the warranty policy for the DC-12?
  A: The DC-12 comes with a one-year parts-only warranty. For the first thirty days, you can return it for a full refund, and after that period, warranty replacement parts shipping is free within the USA, US possessions, and US military bases.

DC-12 Installation Instructions for Jeep™ JK/JKU Front Doors v.051524
NOTE: Follow all safety protocols during installation. Wear protective eyewear and gloves. Installation Time: About ten minutes
Tools you will need: Screwdriver with a T30 Torx™ Driver Bit & a 10mm socket wrench w/extension

Package Content s: Qty. 2: Carrier/Flex Arm Assembly, Qty. 2: Receiver, Qty. 4: M6-1.0X40mm Bolts, Qty. 4: M6-1.0X45mm Bolts, Instructions

• Step 1. In this example we’ll be working with the driver’s side door, but the instructions are applicable for either front door. Remove the label on the Flex Arm indicating “Driver’s Side” (not shown). Then remove the Jeep’s™* existing Door Check Strap from the Body Loop Bracket
• Step 2. Use your 10mm socket wrench to remove & set aside the two bolts that hold the Body Loop Bracket in place. These will be replaced with the furnished M6-1.0X40mm Flanged Hex Bolts
• Step 3. Arrange the Receiver to align on top of the Body Loop Bracket as shown. Then, using the furnished M6-1.0X40mm Flanged Hex Bolts, attach the Receiver and the Body Loop Bracket back into that same location using your 10mm socket wrench.
• Note: The Door Check Strap and its Electrical Wiring is to be Routed Below the Receiver.
• Do NOT Pinch Wires or the Door Check Strap with the Body Loop Bracket or the DC-12 Receiver
• Step 4. Using your T30 Torx™* bit tool, remove & set aside the existing bolts. Then using the provided M6-1.0X45mm Socket Cap Bolts, install the Carrier on top of the existing Door Loop. Do not pinch the Door Check Strap with the Carrier. Fasten the Carrier bolts to the door with minimal torque so that there is some slight sliding movement available to the Carrier. These bolts will be torqued down in Step 6.
• Step 5. With the door open to its maximum position, take the free end of the Flex Arm and align it with the rectangular opening of the Receiver and then slowly and carefully close the door. The Flex Arm should easily slide into the Receiver to the first check position with an audible “click”. If it doesn’t slide easily into the Receiver, Do Not Force it. It is not aligned properly. Please back it out and try again.
• Step 6. After the Flex Arm has been correctly inserted into the Receiver, while holding onto the door, slowly swing it a couple of times. Then you may tighten the M6-1.0-45mm Socket Cap Bolts on the Carrier. Once this is done, you can then re-install the Door Check Strap onto the Body Loop Bracket.
  Last Item, check to be certain that the free end of the Flex Arm Does Not re- enter or escape the Receiver when the door is fully open, if it does, adjust the Door Check Strap to shorten it appropriately.
  Now your installation is complete!

*Jeep™ JK/JKU Door Removal with the DC-12 Installed**

• NOTE: Follow All Safety Protocols. Wear Protective Eyewear and Gloves
• Follow your standard door removal procedure (Reference the manufacturer’s manual that came with your vehicle). The only additional step beyond those is that after the removal of the Check Strap from the Body Loop and disconnecting any and all wire connectors, you should slowly open the door while maintaining control of, what will become, the free end of the Flex Arm. Continue opening the door until the Flex Arm is free and clear of the Receiver. Removal of the Flex Arm assembly from the door during storage is optional.

Warranty

• For the first thirty (30) Days of the one-year parts-only warranty, you may return the DC-12 for any reason for a full refund. You are responsible only for the cost of return shipping to our Houston,
• Texas facility. The warranty period begins on the date that the DC-12 is delivered to your location and is only valid to the original purchaser. Warranty replacement parts shipping is free, but only to customers located in the USA, US possessions and US military bases. Others will be quoted the cost of shipping before we fulfill those warranty replacement parts.

Care and Maintenance

• The DC-12 uses only dry lubrication. While the materials used in its construction are self-lubricating, you may elect to use additional lubrication. If doing so, use only pure PTFE lubricants. The use or application of any silicone, petroleum-based lubricants or other products containing chlorinated solvents etc. will harm the unit and VOID THE WARRANTY. For optimal performance, simply keep the
• DC-12 clean, dry and free of any dirt or other contaminants.
• Manufactured and Distributed by:
• Location
  • Intech Bearing Inc.  1993 Tellepsen St.  Houston, TX USA 77023
• Contact
  • Ph.: 713.926.1136
  • Toll-Free: 800.327.7424
  • Fax: 713.926.3110
• email: sales@intechbearing.com
• web https://intechbearing.com
• web https://urbanescape.tech

J eep™ is the registered trademark of Daimler-Chrysler (2007) Chrysler LLC (2007-2009) Chrysler Group LLC (2009-2014) FCA US LLC (2014-2018), Stellantis N.V. *Torx™ is the registered trademark of Acument Intellectual Properties LLC… and there is no association, whatsoever, with Intech Bearing Inc., UrbanEscape or the DC-12 trademarks/brands or their associated organization(s)

References

• intechbearing.com
• urbanescape.tech

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>