SodaRide CUPHOLDERWLCG Wireless Charging Car Cup Holder Expander Tray Instruction Manual

SodaRide CUPHOLDERWLCG Wireless Charging Car Cup Holder Expander Tray

Product Information

Specifications:

• Model: Z4t
• Power: 4S2
• Frequency: Y@VS4t
• Compliance: FCC Class B digital device
• RF Exposure: FCC radiation exposure limits

Product Usage Instructions

Installation:

1. Ensure the device is placed in a residential installation.
2. Keep a minimum distance of 20cm between the device and your body.
3. Connect the device to a power source with appropriate voltage.

Operation:

Follow these steps to operate the product:

1. Turn on the device using the power button.
2. Adjust settings as needed using the control panel.
3. To avoid interference, keep other electronic devices at a distance.

FAQ

Q: What should I do if the device causes interference?

A: Try turning the device off and on. If interference persists, follow these steps:

• Reposition the device and receiver.
• Plug the device into a different power outlet.
• Contact customer support for further assistance.

Q: How can I ensure compliance with FCC regulations?

A: To comply with FCC rules, keep a minimum distance of 20cm between the device radiator and your body during operation.

PRODUCT IDENTIFICATION

6 Pieces

DIMENSIONS

• Upper Cup Holder: 3″ diameter wide normal cup holder
• Lower Cup Holder: 4″ diameter wide normal cup holder
• Expandable Base: Expands from 2.6″-3.9″
• Attachable Tray : 10.2″x7.4″×0.8″
• Power Cord : 47″

Warnings & Cautions

1. Please make sure your OEM cup holder is round in shape, diameter is between 2.6″-3.9″.
   SodaRide cup holder expander tray is not applicable in the below situation:

2. × Too close to the central dashboard/shift knob.

3. × The raised edge obstructs the cup holder.

4. × The board obstructs the cup holder.

5. × Cup holder with Oval/square/semicircle/irregular shape.

6. The load of the tray is limited, less than 4kg.

7. Keep away from children and pets. Mishandling may cause injury.

8. For optimal charging efficiency, remove the Anti-Slip Rubber Pad if cell phone case is thick.

Cup Holder Installation

Step 1
Place the cup holder expander into the OEM cup holder. Ensure that all three legs are on the inner wall of the cup holder, and no leg is stuck at the notch.

Step2
Press the two buttons and turn it clockwise until the base is securely fixed.

Cup Holder Disassembly

Step 1
Press the two buttons and turn it anti-clockwise to retract the 3 feet.

Tray Installation

Step 1
Install the food tray onto the connector.

Step 2
Slide the connector on the cup holder until it clicks.
360* Rotating Tray

Tray Disassembly

Step 1
Press the 2 locks towards the center and push the tray out of the connector.

Step2
Lift the plastic lock and slide upwards.
Please hold the other end and slide it slowly.

Wireless Charger Usage Diagram

Dual Wireless Charger 30W TOTAL MAX

Support Apple and Android wireless charging protocol.
Charging power varies according to phone models, Apple 7.5W/5W,Android 15W/10W.

Warranty & Disclaimer
We want you to be 100% confident in your purchase and thus offering a One Year Warranty for this product. However, SodaRide is not liable for any consequential damages arising from the improper use or installation of the product. If the product is installed in a non-specified manner, SodaRide reserves the right to reject any warranty claim at the discretion of the technical support department.

www.sodaride.com
Contact us: info@sodaride.com

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>