User Manual

Mooas  Crystal Lamp 3 In 1 Magsafe Stand

Product’s Visual Look

Operation Instruction

1. This product can simultaneously charge mobile phones, watches, and wireless charging boxes for headphones that support wireless charging functions.
2. Please connect this wireless charger to the 5V3A and 9V/3A adapters through a Type e-c fast charging cable and connect to the source.
3. Place the phone in the phone charging area to charge the phone.
4. Place the watch in the watch charging area to charge it.
5. Place the earphone wireless charging box in the earphone charging area to charge the earphone wireless charging box.

Status of Indicator

Mode| LED crystal night lamp| Charging indicator
of headphone box
---|---|---
Electrifying| Warm white light to white
light again to warm white light| —
Standby| Constant light on with warm white light| —
Mobile
phone charging| Keep the previous light mode| —
Charging
of headphone box| —| Breath once and turn
to constant light on mode
Charging Is full| Keep the previous light mode| light Keep the previous mode
Foreign objects on mobile phones and headphones| Warm white light flashes| —

Conversion of LED Crystal Night Lamp

Long press to adjust light brightness

Long press to adjust the brightness of the lamp. The first long press changes from bright to dark (the brightness is at its brightest state when powered on), and then press and hold again to change from dark to bright. If the previous adjusted brightness was from bright to dark, then when pressing and holding again, the lamp will gradually brighten. The brightness has a memory function, if without unplugging, the brightness will restore to its previous status when switching on the lamp.

Lamp-on charging mode of headphone charging box:

1. Equipped with charging indicator function, the charging indicator turns on if with device and turn off if without device.

Caution

To ensure safety and efficiency when charging three devices simultaneously, it is recommended to use a 9V/2A or higher adapter and fast charging cable. For example, when the power of the fast charging part of the phone needs to reach 15W, you must use a 9V/3A adapter and fast charging cable. (e.g If a 5V/2A or lower adapter Is used, this charger may not be able to charge three devices simultaneously.

Detachable Watch Charger

Product Parameters

Product name
mooas Crystal Lamp 3 inl Magsafe Stand
Input
DC5V/3A 9V/3A
Output(Mobile-phone)
5W/7.5W/1 Own sw(Max)
Product size
104mn179.5MM*118MM
Conversion efficiency
Slow Charging ≥70% fast charging ≥75%
Output (Earphone charging box)
5W(Max)
Operation frequency
Output (Watch)
5W(Max)
110-205KHz
Material
ABS+PC+Acrylic
Valid distance for wireless charging(mobile-phone)
≤5mm

Cautions

Applicable Devices

Please check whether your mobile-phone supports wireless charging function or not This product supports fast wireless charging function and achieves short distance wireless energy transmission through coil induction.

Selection of Adapter

When using a 5V/2A output adapter, the wireless charger supports a SW load. When using an adapter that meets the QC3.0 standard, the wireless charger supports a 15W load.

To ensure the normal use of the charger, it is recommended to use PD fast charging or adapter that meets the QC3.0 standard.

Warning!

*Do not place metal debris or magnetic cards on the charging board, as it may cause the charger to heat up! Foreign objects should be removed when alerting.

*Slight heating is a normal phenomenon, and the mobile-phone battery will generate heat during charging.

*Do not place the charger near a fire source or corrosive environment.

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located for operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference.
(2)This device must accept any interference received, including interference that may cause undesired operation.

Packing List

• Wireless charger X1
• Data cable x1
• User Manual X1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>