iCam365 Camera App User Guide
- June 26, 2024
- iCam365
Table of Contents
Connect the device
App will be updated continuously, and the interface is subject to App
Scan the OR code to download the “iCam 365” App
Download the app
Use the “Scan” function of your mobile phone to scan the OR code, download and
install the “iCam365” APP
Connect power
Connect the device to the power supply and wait for about 1 minute
Add Device
- log in
- Add device
- Scan the OR code of the fuselage
- Waiting for a utomatic recognition
- Select the WiFi to connect to and enter the assword
- Show the QR code to the device lens,When you hear the beep, tick i have heard it Then click next
- Waiting to configure the etwork
- The addition is complete, the device is named.
- The device will appear on your homepage
Common problem
| Problems | Solution |
|---|---|
| What should i do if the device is unsuccessfully added? | Check whether the |
WiFi password is correct, and the network can be connected correctly, then
RESET the camera, and add it again after completion.
How to download video?| Click the “Record Screen” button during playback, and
click the red button after recording, and the video file will be saved to the
phone;
What if the display device is offline?| First confirm whether the power supply
and network are normal, and there is no problem before powering off the camera
and restarting it. If the connection is still disconnected
The memory card is full, what should i do?| No manual processing is required.
When the remaining memory card capacity is less than or equal to 500M, the
camera will automatically overwrite the oldest video file.
The memory card shows no memory card or abnormal| 1. The camera does not
support hot swapping. When inserting a memory card, it needs to be powered
off. Please restart the camera.
2. The memory card is still not recognized after restarting the camera,
please replace with a new card and test again.
3. If the new card is still not recognized, the card slot may be damaged or
the cable is faulty. Contact the upplier to replace the device.
What should i do if i cannot receive the warning message?| Confirm whether the
system has turned off the message push permission of iCam365. If it is turned
off, please turn on the “message notification” permission in the phone
settings and check whether the message push is turned off in the device
settings.
Alarm messages are stored for up to 7 days
Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However. there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
NOTE: This device and its antenna(s) must not be co-located or operation
in conjunction with any other antenna or transmitter
This equipment complies with FCC exposure limits set forth for an uncontrolled
environment.
This equipment should be installed and operated with minimum distance of 20 cm
between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>