iF Design 614422 4k Wireless Conferencing System User Guide

iF Design 614422 4k Wireless Conferencing System

PRODUCT INTRODUCTION

• Connect is an all-in-one wireless conferencing system designed to simplify your meetings. With full BYOD support, it allows you to effortlessly connect your laptop to the speakerphone using a single cable. Enjoy 4K wireless screen casting, access to conference camera streaming in 1 0S0P, and the convenience of plug-and-play functionality without the need for software or drivers.
• Connect streamlines your conferencing experience, eliminates cable clutter, and ensures secure and efficient collaboration.

WHAT’S IN THE BOX

HOW TO START

1. Connect the R1 C receiver to the display using the power cable and HDMI cable. If the display does not have a Type-C port to support power more than 5V /2A, use the included switch cable to convert it into two USB-A connectors. One of the USB-A connectors should be USB3.0, which can supply power for the receiver. Alternatively, you can connect the Type-C cable to a power adapter.
2. To connect a USB webcam, plug the camera’s USB cable into the USB-A port on the receiver.

Wireless Conferencing Casting and Speakerphone can be used in projectors, diaplay screens and other equipment

3. Mount the receiver Rl Con the display using the built-in mounting clip. Ensure that the receiver is positioned towards the front side for optimal wireless signal transmission. The optimal wireless transmission range is within 5 meters.

4. Switch the display output source to the connected HDMI port.

5. Connect the speakerphone Ml s to a full-featured Type-c port on your laptop. Wait until the screencasting button light turns green, then press the button to start casting your screen. Press the button again to pause screencasting.

   • In the case where the laptop’s type C port does not meet the full feature requirement, use the USB-C to HDMI & USB-A adapter instead.

   • Use the USB 3.0 extension cable if the laptop’s U5B3.0 port is not nearby the HDMI port.

6. To use the speakerphone MlS and access the camera wirelessly, in your video conference software, select “Connect Video Device” as your microphone, speaker, and camera.

“Connect Video Device” option is only available in the camera device list when a camera is connected to the receiver.

SPECIFICATIONS

Microphone

Built-in Microphone| 8 MEMS Microphone for 360-degree pickup
---|---
Pick-up Distance| 4m
Signal/Noise Ratio (SNR)| 94dB SPL@l KHz 65dB(A)
Sensitivity| 94dB SPL@l KHz -37±1dB FS
Acoustic Overload Point| 132.SdB FS, 10%THD@lKHz
Frequency| 20Hz – 8000Hz
Duplex| V
Beamforming| V
Automatic Noise

Suppression

|

V

Acoustic Echo Cancellation| v
Automatic Gain Control| v

Speaker

Wi-Fi

Quick UDP Internet Connections

Transmission Distance| Up to l0M
Frequency bands and the maximum transmitted power ( For EU)| 5180-5320MHz (Wi-Fi 5GHz) , Max 23dBm

5500-5700MHz (Wi-Fi 5GHz) , Max 23d8m

(Support TPC)

RF Software Version:| 3.0.1
RF Hardware Version:| 1.0.0

Camera Streaming

Screen Casting

Max. Screen Output

Resolution

| 3840×2160 @30FPS
---|---
Average Latency| 150ms

Others

1 / 0 Interface| Speakerphone (MlS): Type CPD+ DP ALT Receiver(Rl C) : HDMI xl; TYPE CPD; USB A 3.0
---|---
Operating Sy s tem| Win 10/ 11; Mac 10.8 and Later
Product Dimensions| Speakerphone (MlS):

180×81 x 32mm / 7.09 x 3.19 x 1.26″

Receiver (Rl C):

102 x 45 x 20mm/ 4.02 x 1.77 x 0.79″

Product Weights| Speakerphone (MlS): 385g / 13.58oz Receiver (RlC): 70g / 2.47oz
Package Contents| Connect:

speakerphone(Ml5) and receiver(Rl C),

l .Sm Type-C to Type-Ccable, 1.5m HDMI Cable,

0.3m USB switch cable

USB-C to HDMI & USB-A Adapter

USB 3.0 Extension Cable

USB Type-C Specification Table

HOW TO USE

M15

R1C

• a Mic Mute

  • Green light : Mic On
  • Red light : Mic off

• b Speaker Volume

• c Screencast
  Press to start/end screencasting

• d Type C cable to laptop
  For power supply and signal transmission

• e Kensington Nano Slot

• f Status Indicator

• g USB Interface for camera
  ( 5V 0.9A)

• h Language / Pair

  • Short press : switch language
  • Long press: Re-pair

• i Power Supply

• j HDMI Out for display

STATUS INDICATORS

Speaker (M1S)

1.  Replug the speakerphone MlS

2.  The receiver RlC is not powered, please replug and

ensure the Rl C indicator light shows static white.

3.  The RlC and MlS are not paired. Please ensure they

are the original paired units. Otherwise please re-pair.

Receiver (R1 C)

REGULATORY AND SERVICE INFORMATION

The products documented in this guide include aspects which are protected under their respective patent, copyright, design copyright, registered design and trademark laws. All other trademarks remain the property of their respective owners.This guide is distributed on line. It may only be reproduced for use within the institution in which the product is used. For use outside of your institution, no part of this guide may be reproduced, transmitted, stored in a retrieval system or translated into any other language without the prior permission of our company. Please note that the content in this guide is protected under copyright law. Although every care has been taken in the compilation of this guide, our company accepts no responsibility for errors or omissions, or for damages resulting from the use of information contained within this guide.

Compliance United States of America

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Do not make any changes or modifications to the equipment.
• 5.15 to 5.25 GHz band, UNII devices will be restricted to indoor operations to reduce any potential for harmful interference to cochannel Mobile Satellite System (MSS) operations .

RF Radiation Exposure Statement Caution : This Transmitter must be installed to provide a separation distance of at least 20 cm from all persons.

Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures :

• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and the receiver.
• Connect the equipment to outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Europe
We declare under our Sole responsibility that the Connect conforms to the essential requirements of European Union Directives 2014/53/EU Radio Equipment Directive (RED), 2014/30/EU Electromagnetic Compatibility Directive, 2014/35/EU Low Voltage Directive and 2011 /65/EU Restriction of Hazardous Substances in Electrical and Electronic Equipment.
These devices comply with RF specifications when the device is used at 20 cm from your body

United Kingdom
We declare under our sole responsibility that the Connect conforms to the essential UKCA requirements 2016 No : 1091. Electromagnetic Compatibility regulations 2016, 2016 No : 1101 Electrical Equipment Safety Regulation 2016, 2017 No : 1206 The Radio Equipment Regulation 2017, and UK SI 2016 No : 1091, Ro HS Restriction of the use of certain Hazardous Substances in Electrical and Electronic Regulations 2012 – UK SI 2012 No : 3032 .

Waste Electrical and Electronic Equipment (WEEE)
For more information concerning the correct disposal of these products, please contact your reseller.

FAQ

• What’s with it when yellow screencast indicator light on M1S?
  Make sure whether the computer connected supports DisplayPort(DP output).

• What’s with it when red screencast indicator light on Ml S?
  Power off and on the Ml 5. Or try pairing again.

• Screencast button does’t work but indicators on Ml S/R1 C are normal?
  Check and confirm whether the Ml 5 matches up with Rl C by their SN.

• When screencasting, there is no content showed on the screen.
  Make sure Rl C is powered on and plugged into the HDMI IN port of the screen, with the proper signal source channel chosen. Try to change to an alternative HDMI IN port if the issue remains.

• Why does my computer fail to screencast at 4K?

1. Make sure the HDMI plugged in display device can support 4K resolution.
2. Check the resolution setting of your computer.
3. Check the computer casting mode, part of the computer to expand the screen can only be 4K cast screen.

• Why does the sound not come out from transmitting device?

1. Check the Ml 5 is set to output device by def a ult in computer audio setting.
2. Make sure the Ml 5 is opted as microphone and speaker.

• How to address echo issues at the other end during meeting?
  Choose Ml 5 as your microphone/speaker to activiate Echo Cancellation.

• Why does the camera not work when plugged into Rl C?
  Camera functionality may vary due to compatibility issues. Recommended to use a suggested camera if you are experiencing lagging or failed recognition.

1. Select Ml 5 as an input camera in camera/conference software setting.
2. Unplug/plug the Ml 5/Rl C, and try after rebooting the system.
3. Check if the power supply exceeds specification, use adapter if it’s the case.

• Why does the device fail to be detected when plugging the Type-c cable of receiver to computer?
  The Type-C port on Rl C is meant for power supply thus no data transmission performed, nor being detected as a device by computer.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>