Hotpoint HTC18D011A1 Integrated Fridge Freezer User Guide

Hotpoint HTC18D011A1 Integrated Fridge Freezer

Specifications

• Energy efficiency class : G
• Number of lateral light sources: 4 (energy efficiency class F)
• Number of top light sources: 1 (energy efficiency class G)

PRODUCT DESCRIPTION

Product Usage Instructions

First Time Use
Wait at least two hours, after the installation, before connecting the appliance to the power supply. Connect the appliance to the power supply it starts the operation automatically. The ideal storage temperatures for the food are preset in the factory. After turning the appliance on, you must wait for 4-6 hours for the correct storage temperature to be reached for a normally filled appliance. Position the antibacterial anti-odour filter in the fan as demonstrated in the filter packaging (if available). If the audible signal sounds, it means that the temperature alarm has intervened: press the button to switch off the acoustic alarms.

Control Panel:
Before using the appliance, carefully read the Safety Instructions. After turning on the appliance, wait 4-6 hours for the correct storage temperature. Position the antibacterial anti-odour filter in the fan as shown in the filter packaging. If the temperature alarm sounds, press the button to turn off the acoustic alarms.

1. LED Light
2. On/Stand-by
3. Freezer and refrigerator compartment temperature button

On/Stand-by:
Press the button for 3 seconds to turn the appliance off. In Stand-by mode the light in the refrigerator compartment does not turn on. Press the button again briefly to reactivate the appliance.

Note: this does not disconnect the appliance from the power supply.

Freezer and Refrigerator Compartment Temperature:
The LED indicators show the refrigerator compartment’s set temperature. You can adjust the temperature with the button. Different temperatures can be set based on the LEDs lit. The three LED indicators indicate the refrigerator compartment set temperature. It is possible to set a different temperature of the appliance with the button.

The following adjustments are possible:

• Set temperature
  • High (less cold)
  • Medium-high
  • Medium
  • Medium-low
  • Low (colder)

Recommended setting:

• Refrigerator compartment: MEDIUM
  To avoid food waste, please refer to the recommended setting and storage times found in the online user manual. After turning the appliance on, you must wait for 4-6 hours for the correct storage temperature to be reached for a normally filled appliance. Position the antibacterial anti-odour filter in the fan as demonstrated in the filter packaging (if available). If the audible signal sounds, it means that the temperature alarm has intervened: press the button to switch off the acoustic alarms.

**FAN***
You can turn the Fan on/off by pressing the button on the base (as shown in the figure). If the ambient temperature exceeds 27°C, or if drops of water are present on the glass shelves, it is essential that the fan is on to ensure the proper preservation of the food. Deactivation of the fan allows energy consumption to be optimised.

FREEZING FRESH FOOD
Place the fresh food to be frozen in the FREEZING ZONE in the freezer compartment avoiding the direct contact with the food that is already frozen. To optimize the freezing speed, the lower drawer can be removed and the food can be placed directly on the bottom of the compartment.

FAST COOL FUNCTION (FAST COOLING)
To quickly cool the refrigerator compartment, or 6 hours before putting a large quantity of food to be frozen in the freezer compartment, turn on the “Fast Cooling” function by repeatedly pressing the button until the 3 icons flash green and then stay constant. The function automatically turns off after 30 hours and the temperature returns to the previous setting when the function is turned on. To turn the function off manually, press the button.

Note: avoid a direct contact between the fresh food and the food that is already frozen.

To optimize the freezing speed, the lower drawer can be removed and the food can be placed directly on the bottom of the compartment.

Fast Cool Function (Fast Cooling):
To quickly cool the refrigerator compartment or prepare for freezing food, turn on Fast Cooling by pressing the button until the icons flash green and then stay constant. The function turns off automatically after 30 hours. Avoid direct contact between fresh and frozen food for optimal results.

Light system (depending on model)

Freezing Fresh Food:
Place fresh food in the Freezing Zone in the freezer compartment without direct contact with already frozen food. For faster freezing, remove the lower drawer and place food directly on the bottom of the compartment. FREEZER COMPARTMENT

1. It is advisable to set the temperature colder or turn on the Fast Freeze/ Fast Cool* at least four hours before removing the food from the freezer compartment, to prolong the preservation of the food during the defrosting phase.
2. To defrost, unplug the appliance and remove the drawers. Leave the door open to allow the frost to melt. To prevent the water from escaping during the defrost, it is advised that you place an absorbent cloth on the bottom of the freezer compartment and wring it out regularly.
3. Clean the inside of the freezer compartment with the ice scraper and dry it carefully.
4. Turn the appliance back on and put the food back inside. To remove the frost on the STOP FROST* accessory, follow the CLEANING.

**Ice cubes***
Fill 2/3 of the ice tray with water and put it back in the freezer compartment. Do not, under any circumstances, use sharp or pointed objects to remove the ice. The quantity of fresh food that can be frozen in a specific time period is indicated on the rating plate. Load limits are determined by baskets, flaps, drawers, shelves etc. Make sure that these components can still close easily after loading

GENERAL INFORMATION
The drawers, baskets and shelves should be kept in their current position unless otherwise specified in this quick guide. The light system inside the refrigerator compartment uses LED lights, allowing for better lighting than with traditional light bulbs, as well as for very low energy consumption. Doors and lids of the refrigeration appliance should be removed before disposal in the landfill, to avoid children or animals getting trapped inside.

**STOP FROST SYSTEM***
The STOP FROST SYSTEM facilitates the defrost procedure for the freezer compartment. The STOP FROST accessory is designed to collect some of the frost that forms in the freezer compartment and it is easy to remove and clean, therefore reducing the time needed to defrost the freezer compartment. To remove the frost on the STOP FROST accessory follow the cleaning procedure demonstrated below.

PROCEDURE TO CLEAN THE STOP FROST ACCESSORY

1. Open the freezer compartment door and remove the upper drawer.

2. Unfasten the STOP FROST accessory and remove it, taking care not to drop it on the glass shelf below.
   Note: if the accessory is jammed or difficult to remove, do not keep trying to remove it, but proceed with the complete defrosting of the freezer compartment.

3. Close the door of the freezer compartment.

4. Remove the frost on the accessory by rinsing it under running (not hot) water.

5. Let the accessory drip dry and dry the plastic parts with a soft cloth.

6. Reinsert the accessory by placing the back part on the projections shown in the figure, then refasten the handle of the accessory to the clasps above.

7. Reinsert the upper drawer and close the door of the freezer compartment.

It is possible to clean the STOP FROST accessory on its own without completely defrosting the freezer compartment. Cleaning the STOP FROST accessory regularly helps to reduce the need  to completely defrost the freezer compartment.

Note : the product specifications, including volume and energy, are calculated without the STOP FROST accessory.

HOW TO STORE FOOD AND BEVERAGE

• For models with “0 ° ZONE” COMPARTMENT the “coolest area” is the one highlighted in the legend
• Only for CB310 e CB380 models (refer to the Rating plate located at side of Fruit and vegetable drawer)

TROUBLESHOOTING

Policies, standard documentation, ordering of spare parts and additional product information can be found by:

• Visiting our website docs.Hotpoint.eu and parts-selfservice.whirlpool.com
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-sales Service, please state the codes provided on your product’s identification plate.

The model information can be retrieved using the QR-Code indicated on the energy label. The label also includes the model identifier that can be used to consult the https://eprel.ec.europa.eu database portal.

FAQ:

Q: How can I silence the audible temperature alarm?
A: Press the button to switch off the acoustic alarms when the temperature alarm sounds.

Q: How do I activate Fast Cooling?
A: Press the button until the icons flash green and then stay constant to activate Fast Cooling. Remember to turn off the function manually by pressing the button when needed.

THANK YOU FOR BUYING A HOTPOINT PRODUCT
In order to receive a more complete assistance, please register your product on www.hotpoint.eu/register Before using the appliance carefully read the Safety Instruction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>