SPARK BELL W23534 Wall Light Flexi Neck Swing Arm Instruction Manual

: June 21, 2024
: SPARK BELL

Table of Contents

SPARK BELL W23534 Wall Light Flexi Neck Swing Arm
Product Information
Product Usage Instructions
Introduction
Parts Included
You will need
Instruction
Adjusting The Fabric Cable
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SPARK BELL W23534 Wall Light Flexi Neck Swing Arm

Product Information

Design: Hand-made wall lights
Origin: United Kingdom (UK)
Standards: Compliant with UK and EU standards

Product Usage Instructions

Installation:

Ensure you have all parts included: x2 per light.
For wall lights installation, use raw plugs.
Hand over the instructions to a qualified electrician for installation.

Adjusting The Fabric Cable:

Warning: Terminals must be relieved from strain or twisting.
Release the grub screw with a 4mm flathead screwdriver.
Adjust the fabric cable to the desired length.
After adjusting, ensure all cables are fully secure in the terminals.
Re-tighten the screw to the same tightness as before.
Ensure proper support for the light before loosening the grub screw.
Leave at least 80mm behind the sconce.
Ask your electrician to carefully strip the excess fabric & PVC cable cover inside the sconce.
Ensure at least 8cm of fabric cable & stripped cable remain.
Secure fabric cable with electrical tape to prevent fraying.

FAQ

Q: What should I do if I encounter loose copper strands?
A: Ensure all colored cables are placed in the same clip and there are no loose copper strands. Secure them properly.
Q: How can I contact customer support?
A: You can contact us at 01273 230566, visit our website sparkandbell.com, or email us at contact@sparkandbell.com.

Introduction

Thank you for purchasing our lights. All of our lights are designed and hand- made in the UK and are made to meet the requirements of UK and EU standards. When you’re ready to install your light, make sure you hand the instructions to a quali ﬁed electrician. With that in mind please:

Shut off the power before installing
Do NOT exceed the wattage listed on the label
These lights are for INDOOR USE ONLY
Always make sure any surface close to the bulb is at least 30mm away to prevent fire hazard
Ensure fixings are appropriate for the mounting surface
crews provided may not be suitable

Parts Included

You will need

Electric Drill
Screwdriver

Instruction

$SPARK-BELL-W23534-Wall-Light-Flexi-Neck-Swing-Arm-Fig- $2$$

When installing wall lights, use Rawl plugs

$SPARK-BELL-W23534-Wall-Light-Flexi-Neck-Swing-Arm-Fig- $3$$ $SPARK-BELL-W23534-Wall-Light-Flexi- Neck-Swing-Arm-Fig- $4$$

Warning:
Ensure all cables are fully inserted into cable clips

$SPARK-BELL-W23534-Wall-Light-Flexi-Neck-Swing-Arm-Fig- $5$$

Adjusting The Fabric Cable

WARNING: Terminals must be relieved from strain or twisting. $SPARK-BELL-W23534-Wall-Light-Flexi-Neck-Swing-Arm-Fig- $6$$
After adjusting, ensure all cables are fully secure in the terminals.
Release the grub screw with 4mm ﬂat head screwdriver.
ENSURE light is properly supported before loosening the grub screw
Adjust the fabric cable to the desired length.
Ensure there is at least 80mm left behind the sconce.
Re-tighten the screw to the same tightness as before.
Ask your electrician to carefully strip the excess fabric & PVC cable cover remaining on the inside of the sconce. Ensure at least 8cm of fabric cable & stripped cable remain. DO NOT attempt this if you are not a trained electrician. $SPARK-BELL-W23534-Wall-Light-Flexi-Neck-Swing-Arm-Fig- $10$$