PENTHOUSE PAWS 2024 Automatic Cat Feeder Instruction Manual
- June 18, 2024
- PENTHOUSE PAWS
Table of Contents
PAWS 2024 Automatic Cat Feeder
Instruction Manual Automatic Feeder
PHP-004 V1.0
Hardware Installation and Introduction
Open the battery compartment at the bottom of the feeder, insert the Micro USB power cord into the connector on the bottom, and extend the power cord out along the designed wire guide. You could also put in 3 pieces of D cell batteries, so that the feeder can still work automatically according to your scheduled feeding plan even without external power supply. Turn on the power switch. Rotate the knob on the top cover, the feeding tray is in the grain bucket. Then place the feeding tray into the feeder from the front. For your pet’s health, please wash the grain bucket and feeding tray regularly. The feeder body should not be filled with water. Please use a wringable wet cloth to wipe.
Attention the following operation panel introduction
Note:
Due to the wide variety of pet foods on the market, the mechanical structure
of the feeder can not guarantee a 100% fit of all types of pet food.
Time Settings
The automatic feeding depends on the correct clock settings in the pet feeder.
Please set the clock before setting up feeding plan. Long press the setting
button for 2 seconds, the icons start to be flashing, it is in settings mode.
As shown in Fig, the clock icon is flashing in default to ready to set up
clock.
Press button to confirm to enter the time setting. The hour is flashing as
shown in Fig2 Use the up/down selection buttons to set the hour (Time -24hour
clock) as shown in Fig3. You can long press the up/down selection button for
fast setting. Press to confirm the hour. Then the minute start to flash, press
the up/down selection button for minute setting, as shown in Fig4 to save and
return to settings mode. Press Back/Cancel button to exit or go on to set up
other settings.
Tips:
All operations during the setup process can be returned or canceled via the
Back/Cancel button.
The signs/numbers shown in screenshots enclosed by the dotted line represent
the actual icon/number in the operation screen,
Manual feeding
The feeder supports fast manual feeding and a scheduled number of manual
feeding functions. In the standby state, you can quickly feed 1 portion by
quickly pressing down button twice within1second.
Feed right now for multiple portions:
Long press button for 2 seconds to enter the setting mode.
Press down button to switch the flashing icon to the feeding one as shown in
Figs.
Press to confirm and manual choose the feeding portions. You can use the
up/down selections button to choose, as shown in Fig6 Press to start feeding.
Meanwhile, the operation screen will display the exact remaining portions need
to feed as shown in Fig7
Scheduled Feeding
The pet feeder support the scheduled feeding exact portions at exact time. The
feeder supports up to 6 meals per day.
Press button for 2 seconds, enter the setting mode. Press down button to
switch the flashing icon to Digital 1icon. As show in Fig8.
Press to select the feeding portions, press up/down button to set portions as
shown in Fig9 and Figl0.
Press to go for feeding time setting as shown in Fig 11 and Fig12,
Press to save. Press Back/Cancel button to exit and the auto feeding icon will
show at standby state, as shown in Figl3. If you need a automatic feeding for
multiple meals, please repeat the above steps and select the corresponding
Digital number icon according to the meals in the setting interface as shown
in Fig14. To cancel a certain automatic feeding, you can set the feeding
portions to be 0. Then second feeding was cancelled as shown in Fig16 and
Fig17.
Feeding Voice Recording
To develop the good feeding habits for pets, the feeder supports pre-recording
a maximum of 10 seconds of audio, which is played during scheduled feeding.
In standby state, press and hold the record button for 3 seconds until the
feeder makes a “Drip” sound, and you can start recording at the microphone
position. Note that the recording button should always be pressed continually
10 seconds during recording. After the recording is completed. the feeder
will make two “Drip” sound.
After recording done, you can preview the recorded audio by short pressing the
record button. If you need to change the recording, please re-record it. The
closer to the microphone, the louder voice can be recorded.
The default of voice recording playback is 3 times. It can be customized 5
times max at the setting:
- Press and hold the setting button for 2 seconds to enter the setting mode.
- Select the down button to switch the flashing icon to recording button as shown in Figl8.
- Press to confirm play times of recording playback by using the up/down buttons as shown in Fig19.
- Press button to save. To cancel the feeding recording and playback, You can set the number of playback to O.
Important Notice:
The pet feeder recording will be played only during scheduled feeding It will
play the times as setting, ex. 3times/4times/Stimes… even the feeder finish
feeding.
When pet food blocked at the food tray, the pet feeder will stop the feeding
to pets for 10 minutes. And the voice recording will be played 1time per
minute to call the pets. If pets finished the food at the tray, the pet feeder
will work as scheduled feeding. Otherwise it will stop feeding if the pets
still did’ finish feeding after 10 minutes.
Turn on/off blue LED
When the feeder is turned LED on in blue, you could press for 6 seconds to turn off/on blue LED. Please notice, only when the feeder is powered by USB cord and the feeder’s LED is not in red at this time, the operation can be operated normally.
Feeder Alarm
When the battery is low, the screen will be displayed low battery sign as shown in Fig20. When the food is insufficient, the screen will display the low food storage as shown in Fig2]; When these two cases happened, the indicator light will be in red. After renewing the battery or re-filling enough food, the red indicator and screen icons will disappear automatically within 60 seconds. ‘When the food is to stuck in food bucket, the screen will display as shown Fig22. The indicator LED will be in red. Please clean up the stuck food manually, and reboot the pet feeder.
Others
Whenever the pet feeder released any of red indicator light, it means that the
feeder has a notification message. Please follow the screen signs remind and
cope with them in time according to manual book illustrated.
The back-up battery is designed for short-term alternative when the external
power supply is cut. Attention! When the pet feeder works with battery back-
up, it will go to sleep mode and some of functions will be limited:
- There will be up to 60 seconds delay for the screen display and scheduled time feeding.
- The blue LED will be turned off automatically.
- For any operations when the screen is off, press any button o wake up the pet feeder from sleep mode.
Reset To Factory Default
If want to delete all previous setting, you can reset the feeder to factory default. In the standby state, press and hold the setting button and button at the same time for 3 seconds until the feeder makes a short beep.
Warranty
12 month warranty
Life-time support
Please contact help@penthousepaws.com for
warranty issues or questions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>