airluv OREO Lollipop Cream Clean Room Instructions

June 15, 2024
airluv

INFORMATION

  • NEWBORN BABY
  • TODDLER
  • JUNIOR

AIPLUV is baby cooling seat pad with air -purifying function. It continuously provides cool wind for baby not to sweat and the HEPA filter purifies the air.

CONTROLLER / REMOTE CONTROL WARNING
  • Always point the remote control toward the Airluv main body.
  • Do not cover the transmitter and receiver of the remote control or controller.
  • The reception rate may decrease depending on the user environment.
  • If the remote control does not work, check the battery status or replace it. (battery: CR2032)
  • Pressing the button hard on the remote control or controller may cause malfunction.
  • The remote control operation may be damaged if it is dropped and got impact on the product
  • Do not spray the remote control with water or put it in water. This may cause malfunction or failure.
  • Pulling the wires hard may cause a short circuit or damage to the product.
FILTER REPLACEMENT / INSTALLATION
  1. Please turn the grill to the left and pull it out.
  2. Insert the new filter grill and assemble it by turning it to the right
  • The slim grill is assembled when delivered, Insert the grill with the filter before using.
  • It is recommended to be used in summer, which provides a stronger breeze
  • The grill with filter is a set. Do not separate it.
  • Always use the fan with the grill inserted. There is a risk of injury if it is not inserted
  • Power mode (4 level) can be noisy and the battery can be run out quickly as it provides strong wind.
  • We recommend to remove the filter from the grill, for a stronger breeze

The service life of a filter is about 6 months, and it may vary depending on the circumstance and period of use. Do not clean the filter with water or any chemical liquid. It is an electrostatic precipitation type air filter, and any liquid could significantly affect the performance. New filters are available atthe place where you purchased or from our distributors in your region.

※The filter is in the pe pouch written as H13 HEPA Filter.

HOW TO WASH / REPLACEMENT

1. Please remove the grill and the fan from the product.

Please loosen the screw and turn the grill counter clock-wise to open.

Please open the zipper at the bottom and remove the fan from the product.

The ventilation hole at the top of the fan box must be placed facing to the top side of the Airluv.

2. Please hand-wash with a neutral detergent.
3. Do not wring out. Please dry in a well-ventilated area.
For a minor contamination of the fabric, you may wipe it off with a wet tissue or soft cloth soaked in water.

WARNING

  • Do not use other than original purposes.
  • If your child uses medical devices or getting medical treatments, please consult with the doctor before using the product.
  • Please stop using if your child feels uncomfortable.
  • If you use a portable charger, please make sure that the output is DC 5V, 3A or higher. (A charger output below DC 5V, 3A can damage the battery of the product.)
  • Please use after assembling the grill properly and closing the zipper.
  • If liquid gets inside the fan, please dry it well before using the product again to prevent any malfunction.
  • The direct sunlight can cause the fabric discoloration.
  • Please make sure you remove the fan before washing the product.
  • Polish remover, fabric deodorizer, wax, acetone etc can damage the fabric.
  • Spicy food (kimchi, curry etc) or deep-colored clothes (such as denim jeans) can stain the product.
  • Deformation, discoloration, and sagging may occur depending on the circumstances and period of use.
  • Please make sure the fan stops turning completely before replacing the filter grill. (Please take 10 seconds or more after turning the power off.)
  • Strong washing or dehydration may damage the product.
  • Do not machine dry to avoid any product deformation.
  • Please loosen the bolt to remove the fan from the product. Please make sure that your children will not swallow the small parts.
  • Keep the fan away from children’s hands.
  • Be careful not to put or get your fingers caught in the fan.
  • It contains small parts and should not be swallowed by children.
A/S OR EXCHANGE / REFUND POLICY
  • We provide parts/components replacement within 6 months after purchasing date in case of defects.
  • Any returned item must be in its original condition and all tags need to be intact.
    Once the returned item is received and inspected, you will be notified of the refund/exchange approval.

GLOBALPOLEDGLOBAL.COM

Please keep this manual after you read through all the details. If you have any queries, please contact our CS team or the place where you purchased.

  1. AIRLUV
  2. USB PORT
  3. BUTTON
  4. HEADREST HOOKS
  5. MAIN BELT
  6. CROTCH BELT
  7. BELT HOLE
  8. GRILL• FAN
  9. ZIPPER
  10. REMOTE CONTROL
INCLUDES

Airluv                                   1EA
Slim Grill (Default)              1EA
H13 HEPA Filter (Extra)     1EA
REMOTE CONTROL        1EA

PRODUCT SPECIFICATION
Name Airluv4 Oreo
Dimensions (W)355 x (H)970mm (±20mm)
Material Polyester , Polyurethane
Use of Age Newborn – Age 4
Manufacturing Date Marked separately
Manufacturer Poled Co., Ltd.
Address 523, Jangsaengdong-ro, Unsan-myeon, Seosan-si, Chungcheongnam-

do, Korea
Origin| China
Customer Service| global@poled.kr
Refund & Exchange| Place of purchase

HOW TO USE
INSTALLATION
  1. Please put the product on the place where to use it.

  2. Please pass the crotch belt through the hole on the bottom of Airluv, and fasten with the belt in the middle and the rubber band on the top.

  3. Please connect the power USB port. (A portable charger etc.)
    • If you use the portable battery charger, please make sure that the output is DC 5V, 3A or higher. (A charger output below DC 5V, 3A can damage the product.)

  4. You may adjust the breeze by pressing the button. (Low ▷Medium ▷High ▷Power ▷Off)

Low                     Medium                 High

Power                       Off

CONTROLLER / REMOTE CONTROL INSTRUCTIONS
  • Can be controlled without remote control
    – Power mode: LED on the control display by 3 levels

  • Operating this remote control may affect other products.
    (Reception may be interfered if the same product or the same KEY value is used as an IR sensor)

In case it runs for a long time with a charger connected, the power can be turned off automatically by the overload protection circuit.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals