Bedside Crib Instruction Manual

Model: BR-Y521
IMPORTANT: KEEP FOR FUTURE REFERENCE READ CAREFULLY

www.besrey.com

support@besrey.com

Mon-Fri, 8 am – 6 pm PST

FUJIAN BESREY BABY PRODUCTS CO., LTD. Made in China

Importer: STIGER, INC.

Address: 1370 VALLEY VISTA DR. STE 200-208 DIAMOND BAR,

CALIFORNIA 91765-0208,

UNITED STATES OF AMERICA

FOR YOUR CHILD’S SAFETY, READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY AND USING THE PRODUCT. FAILURE 10 FOLLOW THESE WARNINGS AND INSTRUCTIONS COULD RESULT N SERIOUS I’IJLRY OR DEATH. KEEP THIS MANUAL FOR FUTURE REFERENCE.

WARNING

DO NOT MOVE THE PRODUCT WITH THE CHILD INSIDE.

DO NOT ADJUST THE PROOUCT WITH THE CHILD INSIDE.

DO NOT USE THE PRODUCT WITH MORE THAN ONE CHILD AT A TIME.

DO NOT USE THE PRODUCT IF ANY PART IS BROKEN. TORN. OR MISSING. ONLY AN ADULT SHOULD ASSEMBLE, FOLD AND UNFOLD THE BEDSIDE SLEEPER. ENSURE USERS OF THIS PRODUCT ME KNOWLEDGEABLE ON ITS CORRECT OPERATOR.

• This product is intended for we for babes aged between 0 and 5 months. weight mg up to a maximum of 194/331b.
• The bedside sleeper is designed for use only with adult beds that are between 232-31.6 inches (59-8Itm) from for to top of the adult knows.
• Before assembly. check that the product and al of its components have not been damaged or missing closing transportation
• Should any pan be damaged or missing.do not use and keep it out of reach of children. Contact besrey for replacement parts and instructions if needed.
• Be sue the product is completely set up before use. including rats filly erected. and the mattress/pad flat.
• The product a ready for use COLT when at locking mechanisms are engaged. Check carefully that these are engaged before we.
• At assembly fittings should always be tightened properly and those fittings should be checked regularly and re-tightened as necessary. When not in we. keep It away from children.
• Never stestitute parts. DO NOT use accessories. spare parts. or any component not supplied or approved by besrey. as they may make the product unsafe.
• Be aware of the risk of open fees and other sauces of strong heat. such as electric bar heaters. gas fires. etc.

ENTRAPMENT/FALL HAZARD

ALWAYS USE ON A FLAT. LEVEL FLOOR. 00 NOT USE THE PRODUCT WITHOUT THE SUPPORT FRAME. THIS BEDSIDE SLEEPER CANNOT BE USED WITH A RECESSED BED. IT IS DANGEROUS TO PLACE THE PRODUCT ON A RAISED SURFACE SUCH AS A TABLE. TO PREVENT SERIOUS CR FATAL INJURY FROM FALLS, NEVER LEAVE THE CHILD UNATTENDED.

• When a clad can sit, kneel pull themselves up, the product should not be used anymore for this child’ Move your Mild to another sleeping product then you child reaches this stage.
• To prevent serious or fatal injury from fats. always keep the child within arm’s reach when using this product. NEVER leave your child I….attended.
• NEVER leave your infant in the product without the GUARCRAL installed in the uppermost position, unless securely attached to the adult bed.
• ALWAYS engage the brakes bake* placing yen/ child in the product BE SURE both sides are locked in position whenever a child is in the product
• To reduce the risk of SIDS (Sudden Infant Death Syndrome), pediatricians recommend healthy infants be placed on their back to sleep unless otherwise advised by your physician.
• Before use in bedside deeper modes (fixed to the bed), make sire the brake system is engaged.
• When the product is used in bedside sleeper mode% make site the securing soaps are hooked and ter coed prcpedy before laying the child in the product.
• It Is recommended to make the straps shorter than the width of the mattress to ensure the product is pressed wanly and tightly against the adult bed.
• There must be no more than a 1/2 inch 03nvn) gap between the product and the adult’s mattress BE SURE that the product’s GUARDRAIL is NOT higher than the adult’s mattress
• failure to use the attachment system that prevents the product to move away from the adult bed could case the infant to fat out of the product when using the ‘bedside sleeper mode%
• The tulle of the Top Support Frame must be fully assembled when not using the ‘bedside sleeper mode as the child will fall out of the soft lining.

SUFFOCATION/STRANGULATION HAZARD

USE ONLY THE PAD/MATTRESS PROVIDED BY THE MANUFACTURER. NEVER ADD A PILLOW, COMFORTER, OR ANOTHER MATTRESS FOR PADDING. THE INFANT MAY SUFFOCATE IN GAPS BETWEEN EXTRA PADDING AND THE SIDE OF THE BASSINET.

• NEVER add soft bedding like a water mattress or down feather cushions, etc. NEVER add a pillow. comforter, or another mattress for padding to reduce depth.
• Use ONLY the mattress provided by bra. Usng a thicker& a different staid mattress/pad may Mesa chid’s head to get between mattress/pad and side of the product causing suffocation.
• Remove and dispose of all plastic bags and packaging materials, and keep them out of reach of children before use.
• NEVER use plastic shipping bags or other plastic films as mattress Coven not sold and intended for that purpose. They can cause suffocation.
• The child can become entrapped and die when Improvised netting or covers are placed on top of the product. Never add such items to confine the child In the product.
• NEVER place the product near a window where cords from bends or &apes can strangle a child.
• Keep the securing straps out of reach of child-en when not using the ‘bedside sleeper’ mode.
• DO NOT place items with a string around the child’s neck such as hood strings, pacifier cords. etc.
• DO NOT suspend strings over the product or attach strings to toys. Do not allow children to climb Inside or play with the travel bag.

Specifications

1. Height Adjusting Handle
2. Buckles foe Securing Straps
3.  9 Adjustable Heights
4. Brakes
5. Co-sleeping Side Top Zippers
6. Foldable Co-sleeping Side
7. Breathable Mesh
8. Bottom Storage Basket

Parts List

The product includes above parts, please check carefully before assembly, DO NOT use product if any part is missing. a

How to Assemble the Bedside Crib

Step 1.

A) Extend bottom tube of the Side Support Bars until you hear a “Click”.

B) Lay one of the Side Support Bars on a flat surface. Securely insert the Bottom Cross-bar into the Side Support Bar until you hear a “Click”.

C) Repeat the process for the other side.

D) Take the 4 wheels out of the package and insert them into the bottom of the holes at the ends of the Side Support Bars to fit completely, and make sure they won’t fall out easily after being inserted tightly.

Step 2.

A) Align the Guardrail and part B of the Middle Support Frame, push them together until you hear a “Click”.

B) Align the buttons and holes on two parts of the Middle Support Frame, push them together until you hear a “Click”.

C) Securely insert both sides of the assembled Middle Support Frame into the Side Support Bars until you hear a “Click”.

Step 3.

A) Align the Top Support Frame and the structure assembled in last step.

B) Securely insert both sides of the Top Support Frame into the Side Support Bars until you hear a “Click”. The co-sleeping side and the Guardrail should be on the same side.

Incorrect assembly might cause collapse while in use! Overloading, incorrect folding and the use of accessories, may cause damage to or break this crib.

Step 4.

A) Make sure the lining is fully expanded.

B) Zip the bottom of the lining after covering the Guardrail.

C) Use the velcro under the lining to securely fasten the lining onto the Middle Support Frame.

Make sure every velcro strip is attached securely.

Step 5.

Put the mattress inside the crib. Make sure it fits snugly into the bottom of the crib.

USE ONLY the mattress provided by besrey.

Step 6.

A) Attach the Bottom Storage Basket with 8 snap fasteners.

B) Make sure every fastener is snapped securely.

The maximum load bearing capacity of the basket should not exceed 3kg/6.61b.

Step 7.

A) Clasp the Mosquito Net at the middle of Top Support Frame.

B) Stretch the 4 corners of the net to cover the crib. The edges of the Mosquito Net and the crib should be in a straight line.

Step 8.

Zip the Mosquito Net. The assembled product should be as shown below.

Check every part is tight and securely fitted before use.

How to Lock the Wheels

A) Press the pedal on the wheel to lock.

B) Lift up the pedal on the wheel to release the lock.

The wheels must be locked before the baby is put into the crib.

How to Adjust the Height

The crib can be adjusted to 9 different heights. To adjust the height, you should:

A) Pull up the handle on the two sides simultaneously.

B) Set a safe height by raising or lowering the crib.

C) Release the two handles to hear a “Click” which means it is locked.

The two sides of the crib must always be set to the same height to ensure a flat and safe sleeping environment for your child.

Suitable only for adult beds with a height of 23.2-31.8 inches (59-81cm) from floor to top of mattress.

How to Use the Bedside Sleeper Mode

Step 1.

A) Unzip both co-sleeping side zippers of the Top Support Frame after removing the MOSQUit0 Net: Push the buttcns and pull out the tube.

B) Align the tube and the holes under the Middle Support Frame: Push them together until you hear a tick’.

Step 2.

Securely attach the Securing Straps to the crib by connecting the buckles.

Step 3.

Check the anchor plates of the Securing Straps and make sure they are secured tightly as below.

Step 4.

A) Remove the mattress from the adult’s bed and put the Securing Straps between the mattress and the bed like shown below.

B) Repeat for the other side; Adjust the length of Securing Straps to make sure they are grabbing the adult’s bed tightly.

Step 5.

A) Make sure there is no more than 1/2 inch (13mm) gap between the adult’s mattress and the crib.

B) Reposition the adult’s mattress.

Make sure the crib is attached securely to the adult’s bed before putting the baby inside.

How to Use the Bedside Sleeper Mode with Ottoman Beds or Divan Beds

Step 1.

Press the button underneath each Side Support Bar.

Step 2.

A) Push the Side Support Bar against the bed to retract the wheels on the co- sleeping side.

B) Make sure there is no gap between the adult’s mattress and the crib.

Step 3.

A) Connect and secure the crib to the adult’s bed in the same way that you would do with a regular bed.

B) Engage the brake during use.

After using the Bedside Sleeper Mode, always fully extend the wheels back to their original position until you hear a “click” to ensure stability.

After using the Bedside Sleeper Mode, always reattach the tube to the Top Support Frame and zip the co-sleeping side zippers.

WARNING

• Make sure there is no more than 1/2inch (13mm) gap between the adult’s mattress and the crib. If there is large gap, tighten the straps to narrow the gap.
• The height of the Guardrail must NOT be higher than the adult’s mattress. If there is, adjust the crib to a suitable height.
• The securing straps should always be put between the mattress and the bed when using “bedside sleeper mode”.
• The crib should always be attached to the long side of the parent’s bed when using “bedside sleeper mode”.
• Use of the product is only permitted with beds and/or mattresses with straight sides, use of the product with a round mattress or water bed is not permitted.

The attachment system must always be correctly used in bedside sleeper mode.

Never use this product in bedside sleeper mode without the anchor plates securely attached to the adult bed.

Mattress and bed frame aligned.

ACCEPTABLE FOR USE

Extended bed frame

NOT ACCEPTABLE FOR USE

Cleaning and Maintenance

This product requires regular maintenance. The crib and the mattress have a stain-resistant fabric cover which is completely removable and washable. The cleaning and maintenance of the crib must only be carried out by an adult.

Clean the Lining

Step 1:

Unzip the lining at top and detach from Top Support Frame

Step 2:

Unzip the lining at bottom and remove from the Guardrail

Step 3:

Detach the velcro at the bottom of the lining

Step 4:

Unzip both co-sleeping side zippers of the Top Support Frame

Step 5:

Push the buttons on both sides

Step 6:

Detach the tube

Step 7:

Pull out the tube from the lining

Step 8:

Pull out the lining

Step 9:
The lining is ready for washing

Clean the Cover

Step 1:

Take out the mattress

Step 2:

Unzip the cover and take out the padding

Step 3 :

The cover is ready for washing

****WARNING

CLEANING

• Hand wash in cold water.
• DO NOT bleach and dry clean.
• DO NOT iron or tumble dry. Drip dry.
• The mattress padding CANNOT be washed.
• Periodically wipe clean plastic parts with a soft damp cloth.
• Always dry the metal parts to prevent the formation of rust if the crib has come into contact with water.
• After each wash check the resistance of the fabric and the stitching.

MAINTENANCE

• Periodically check the crib for loose screws, worn parts, torn material or stitching. DO NOT use if any irreparable damage occurs.
• Use only the replacement parts provided by besrey.
• Keep the crib in a dry place. If crib gets wet, open crib and allow to dry completely.
• Prolonged exposure to direct sunlight may cause the fabric to fade and plastic parts to warp.

References

• U.S.C. Title 15 - COMMERCE AND TRADE
• List of CPSC-Accepted Testing Laboratories | CPSC.gov

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>