N OVEEN HC1500 Air Curtain User Manual
- June 12, 2024
- N OVEEN
Table of Contents
- IMPORTANT SAFEGUARDS
- PARTS DESCRIPTION HC1500/HC2000
- PARTS DESCRIPTION HC2050
- PARTS DESCRIPTION HC2100
- PARTS DESCRIPTION HC2200
- HC2500
- HC3100/3200
- INSTALLATION OF THE APPLIANCE
- OPERATION INSTRUCTIONS
- CONTROL PANEL
- REMOTE CONTROL HC1500/HC2000/HC2050
- REMOTE CONTROL HC2100
- REMOTE CONTROL HC2200
- REMOTE CONTROL HC2500
- REMOTE CONTROL HC3100/3200
- OVERHEAT PROTECTION
- CLEANING AND MAINTENANCE
- TECHNICAL SPECIFICATION
AIR CURTAIN – USER MANUAL
HC1500 / HC2000 / HC2050 / HC2100 / HC2200 / HC2500 / HC3100/3200
HC1500/HC2000
HC2050
HC2100
HC2200
HC2500
HC3100/3200
IMPORTANT SAFEGUARDS
Thank you for buying our product. Please read this instruction carefully before operating the heater. Keep this operating instruction for future reference.
- The heater should be hung on the wall and make the wind outlet down. You must not place it precipitantly or tipsily.
- Please do not use the heater in the place where full of combustible or explosive gas. Don’t cover the wind outlet.
- If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
- The heater must not be located immediately below an electrical socket. The electrical socket must be equipped with earth wire, its capacity should be 220-240 V ~10A. The socket and the power plug should be in good connecting condition.
- If nobody is in using or you are repairing the heater, please pull off the plug.
- Please don’t touch the heater by the wet hand or other conductor.
- If motor is not working properly, please stop it immediately.
- During using the heater, please do not open the door or window continually otherwise it will influence the heating effect.
- If want to shut off the heater, press the on/off switch to off, then the heater will keep the fan working 30 seconds until it blowing out cool wind, then the heater will stop working, and you may pull off the plug.
- Do not use this heater in bathroom.
- Timer sets the heater working time.
- Remote control, please use 1 battery.
- The heater must be installed at least 2 m above the floor.
- If the heater needs repair, please ask for special person or our company authorized maintenance department.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Children of less than 3 years should be kept away unless continuously supervised.
- Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
18. CAUTION —some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
PARTS DESCRIPTION HC1500/HC2000
No
| Part name| No|
Part name
---|---|---|---
1| Cover| 12| Ring
2| Display| 13| Bearing bar
3| Panel| 14| Wheel
4| Control board| 15| Locating ring
5| Receiving window| 16| Motor trim
6| Button| 17| Shaded pole motor
7| PTC heating element| 18| Protective coil
8| PTC flap| 19| Plate
9| Wind outlet| 20| Power cord
10| Ceramics thermal protection| 21| Power board
11| Thermostat| 22| Base
PARTS DESCRIPTION HC2050
No
| Part name| No|
Part name
---|---|---|---
1| Cover| 12| Ring
2| Display| 13| Bearing bar
3| Panel| 14| Wheel
4| Control board| 15| Locating ring
5| Receiving window| 16| Motor trim
6| Button| 17| Shaded pole motor
7| PTC heating element| 18| Protective coil
8| PTC flap| 19| Plate
9| Wind outlet| 20| Power cord
10| Ceramics thermal protection| 21| Power board
11| Thermostat| 22| Base
PARTS DESCRIPTION HC2100
No | Part name | No | Part name |
---|---|---|---|
1 | Cover | 13 | Control board |
2 | Motor plate | 14 | Circuit board |
3 | Motor | 15 | Stepping motor sleeve |
4 | Bearing sleeve | 16 | Stepping motor |
5 | Wheel | 17 | Shutter |
6 | Bearing plate | 18 | Capacitance |
7 | PTC board | 19 | Protective coil |
8 | PTC heating element | 20 | Board |
9 | Thermostat 21 | 21 | Terminals |
10 | Ceramic thermal protection | 22 | Power cord |
11 | Wind outlet | 23 | Base |
12 | PVC sticker |
PARTS DESCRIPTION HC2200
No | Part name | No | Part name |
---|---|---|---|
1 | Button | 15 | PTC fixed frame |
2 | Control panel | 16 | Link |
3 | Circuit board | 17 | Stepper motor |
4 | Decorative plates | 18 | Stepper motor baffle |
5 | Top cover | 19 | Swing leaf guide shaft |
6 | Bearing bead | 20 | Pendulum |
7 | Motor bead | 21 | Capacitance |
8 | Fan motor | 22 | Power board |
9 | Bearing base | 23 | Protective coil |
10 | Wheel | 24 | Crimping board |
11 | PTC heating element | 25 | Terminal |
12 | Mesh | 26 | Power cord |
13 | Ceramic heat protection | 27 | Lower cover |
14 | Thermal thermostat |
HC2500
No
| Part name| No|
Part name
---|---|---|---
1| Light cover| 14| Stepper motor
2| Display| 15| Pendulum
3| Decorative screen| 16| Wind wheel cover
4| Sticker| 17| Motor support
5| Power control board| 18| Motor
6| Control board| 19| Wind wheel
7| Panel| 20| Crimping board
8| Resettable thermal| 21| Power cord
9| Thermal protection| 22| Power board
10| PRC baffle| 23| Base
11| PTC heating element| 24| Power switch
12| Air outlet| 25| Button ON / OFF
13| Stepper motor bushing| |
HC3100/3200
No
| Part name| No|
Part name
---|---|---|---
1| Panel| 14| Wind wheel cover
2| Front cover| 15| The motor bracket
3| PVC sticker| 16| Fan motor
4| Inner screen| 17| Wind wheel
5| PCB (Control panel)| 18| Fixed plate for power supply cord
6| Thermostat| 19| Power plug
7| Thermal fuse| 20| PCB (main power)
8| PTC fixer| 21| Base
9| PTC heating element| 22| Power switch
10| Air outlet| 23| One touch button
11| Locating ring for DC motor| |
12| DC motor| |
13| Louver| |
INSTALLATION OF THE APPLIANCE
The heater should be installed and used according to the safe standard.
To avoid all dangers, follow the safety instructions.
– The installation must be done by the service agent or similarly qualified
persons in order to avoid a hazard.
– Important! Make sure that there are no electric cables or other
installations (for example water pipes) near the drill holes. Make sure that
the appliance is securely and vertically fitted to the wall.
Get two holes on the wall 2 m above the floor and near the corner more 0,25 m,
be sure to make the diameter just as same as the expanding pipe. Fix two
screws on the expanding pipe, keep the tips of the screws out for 10mm, and
hang up the machine after the screws are fixed enough.
HC1500/HC2000/HC2050:
385 mm
HC2100: 535 mm
HC2200: 545 mm
HC2500: 330 mm
HC3100/3200: 330 mm
See Picture 1
OPERATION INSTRUCTIONS
- Before inserting the plug into an electrical outlet, make sure that the electrical supply in your area matches that on the rating label on the unit.
- Carefully remove the heater from the plastic bag and the carton.
- Place the heater on the wall, setting the master button to “-” position. Plug the cord set into a AC220-240V~ electrical outlet, with “BEE” sounds the “Power” light is on and the heater will shows the default temperature, it will twinkle 3 seconds.
SET TIME HC1500/HC2000 / HC2050 / HC2200
Before turn on the heater, set the right time. Press remote control “ ”
button, control panel shows current room temperature.
WEEK Press “Set” button one time, ”I/W” (HC1500/HC2000/HC2050) or
”W-Timer/W” (HC2200) lights on, press “ ” buttons to set the week from 1-7
(1=Monday, 2=Tuesday…7=Sunday)
HOUR Press “Set” button again, ”II/H” (HC1500/HC2000/HC2050) or ”24h/H” (HC2200) lights on , press “ ” buttons to set the Hours from 01–00 (01=1 o’clock, 02=2 o’clock…00=24 o’clock)
MINUTE Press “Set” button again, ”Fan/M” (HC1500/HC2000/HC2050) or ”Auto/M” (HC2200) lights on, press “ ” buttons to set the Minutes from 00–59 (01=1 Minute, 02=2 Minute etc.)
PS: Press “Set” button, screen shows number that will twinkle for 5 seconds, you should operate in time, otherwise appliance will get back to standby. (Appliance will keep the right time until power off)
SET TIME HC2100/HC2500/HC3100/3200
Before turning on the heater, set the time as right time. Press “ ” button on remote control, LED display shows 00:00 and “Mo” lights on.
HOUR Press “Set” button one time, LED displays “00:00” twinkling, press“ buttons to set the Hours from 01—00 (01=1 o’clock, 02=2 o’clock…00=24 o’clock)
MINUTE Press “Set” button again, LED displays “00:00” twinkling, press “ buttons to set the minutes from 00—59 (01=1 Minute, 02=2 Minute etc.)
WEEK Press “Set” button again, “Mo” light twinkles, press “ buttons to set the week from Mo–Su (Mo=Monday…Su=Sunday etc.)
PS (HC1500/HC2000/HC2050/HC2100/HC2200/HC2500/HC3100/3200): Press “Set” button, screen shows number that will twinkle for 5 seconds, you should operate in time, otherwise appliance will get back to standby. (Appliance will keep the right time until power off)
GENERAL OPERATION
1. Turn the heater ON by pressing the ON/OFF main button, the unit will blow the cold air and “Fan/M” (HC1500/HC2000/HC2050) “ ” HC2100/HC2500) or “Power/Fan” in red color (HC2200) light is on.
2. Press the “MODE” button, the unit will blow the warm air and both “I/W” and “Fan/M” (HC1500/HC2000/HC2050) “ ” and “ ” (HC2100/HC2500) or “I/II” in green color (HC2200) or (HC3100/3200) lights are on.
3. Press the “MODE” button second time, the unit will blow the hot air and both “II/H” and “Fan/M” (HC1500/HC2000/HC2050) “ ” and “ ” (HC2100/HC2500) or “I/II” in red color (HC2200) or (HC3100/3200) lights are on.
4. Press the “MODE” button third time, the unit will blow the cold air and “Fan/M” light is on. PS: Control panel and remote control are operated the same way.
PS (HC2100): On control panel “ ” button, press 1st time: COOL AIR; 2nd time: WARM
AIR; 3rd time: HOT AIR; 4th time: SWING FUNCTION; 5th time: OFF.
24H TIMER FUNCTION
1.Turn on the appliance in fan, warm, hot mode. Control panel “TIMER” button (HC1500/HC2000/HC2050/HC2200) or “ ” (HC2100) and remote control “ ” work the same way.
2. Press “TIMER” button (HC1500/HC2000/HC2050/HC2200) or “ ” (HC2100) or (HC2500/HC3100/3200), set the timer up to 24 hours, keep pressing “TIMER” button to increase the hours from 00–24 (00= off, 01=1hour, 02=2 hours…24=24 hours) and the
“TIMER” (HC1500/HC2000/HC2050) or “ ” (HC2100/HC2500/HC3100/3200) or “24h/H” (HC2200) light is on.
PS: “00” set means no timer is set, the “TIMER” (HC1500/HC2000/HC2050) or “ ” (HC2100/HC2500/HC3100/3200) or “24h/H” (HC2200) light is off.
THERMOSTAT INSTRUCTIONS
1. Turn on the appliance in fan, warm, hot mode. This function only works
through remote control.
2. To adjust temperature, press “ ” to set the desired temperature between
10-49 . ℃
3. When the air temperature drops 2 degree below the set temperature, the
heater will start heating with ”I/W” (1000W).
4. When the air temperature drops 4 degree below the set temperature, the
heater will start heating with” II/H” (2000W).
5. When the air temperature 1 degree higher than set temperature, the heater
will blow the cold air.
WEEK TIMER FUNCTION (HC1500/HC2000/HC2050/HC2200)
1. Turn on the appliance in fan, warm, hot mode. This function only works
through remote control.
2. WEEK Press “ ” button, ”I/W” and ”W-Timer” lights are on, “1” means
“Monday”.
HOUR Press “ ” button 2nd time, ”II/H” (HC1500/HC2000/HC2050) or ”24h/H”
(HC2200) lights on, press “ ” to set the Hours from 01–00 (01=1 o’clock, 02=2
o’clock…00=24 o’clock)
MINUTE Press “ ” button 3rd time, ”Fan/M” (HC1500/HC2000/HC2050) or
”Auto/M” (HC2200) lights on, press “ ” to set the Minutes from 00–59 (01=1
Minute, 02=2 Minute etc.)
———————————————————This is open time
HOUR Press “ ” button 4th time, ”II/H” (HC1500/HC2000/HC2050) or ”24h/H”
(HC2200) lights on, press “ ” to set the Hours from 01–00 (01=1 o’clock,02=2
o’clock…00=24 o’clock)
MINUTE Press “ ” button 5th time ,”Fan/M” (HC1500/HC2000/HC2050) or
”Auto/M” (HC2200) lights on, press “ ” to set the Minutes from 00–59 (01=1
Minute, 02=2 Minute etc.)
———————————————————This is close time The above settings are finished for Monday Timer.
3. Press “ ” button once more, ”I/W” (HC1500/HC2000/HC2050) or ”W-Timer/W” (HC2200) lights on, “2” means “Tuesday”. Please note that the setting for open time HOUR/MINUTE and close time HOUR/MINUTE are the same as for Monday.
4. When 1-7 (1=Monday, 2=Tuesday…7=Sunday) settings are all set, press “ ” button on remote control 7th times to set from Monday to Sunday’s temperature and press “ ” to select the temperature which you need, the temperature range is from 10 to 49 . ℃ ℃
PS: In Week timer function, when you set today’s temperature, the thermostat function will start and function the same as in 4) THERMOSTAT INSTRUCTIONS. You can set different open time, close time and temperature within the whole week.
WEEK TIMER FUNCTION (HC2100/HC2500/HC3100/3200)
1. Turn on the appliance in fan, warm, hot mode. This function only works
through remote control.
2. Frist press “ ” button, then press “ ” buttons to select which model you
want. This function have 6 models, P1-P5 is smart model where appliance have
it’s own schedule, check the details below
Week | Mo | Tu | We | Th | Fr | Sa | Fr |
---|
Model
P1| 8:00- 17:00| 8:00- 17:00| 8:00- 17:00| 8:00- 17:00| 8:00- 17:00|
8:00- 17:00| 8:00- 17:00
P2| 18:00- 07:00| 18:00- 07:00| 18:00- 07:00| 18:00- 07:00| 18:00-
07:00| 18:00- 07:00| 18:00- 07:00
P3| 8:00- 17:00| 8:00- 17:00| 8:00- 17:00| 8:00- 17:00| 8:00- 17:00|
OFF| OFF
P4| 18:00- 07:00| 18:00- 07:00| 18:00- 07:00| 18:00- 07:00| 18:00-
07:00| OFF| OFF
P5| OFF| OFF| OFF| OFF| OFF| 00:00- 24:00| 00:00- 24:00
3. P6 is user-defined, press “ ” buttons to select P6 model:
WEEK Press “ ” button 1st time, ” ” lights on, means “Monday”.
HOUR Press “Set” button 2 and time, LED displays “ 00 :00” twinkling,
press“ buttons to set the Hours from 01—00 (01=1 o’clock, 02=2 o’clock…00=24
o’clock)
MINUTE Press “Set” button 3 red time, LED displays “ 00 :00”
twinkling, press “ buttons to set the minutes from 00—59 (01=1 Minute, 02=2
Minute etc.)
With the “ **” light on, it means open time.
HOUR Press “Set” button 4th time, LED displays “ 00 :00” twinkling,
press“ buttons to set the Hours from 01—00 (01=1 o’clock, 02=2 o’clock…00=24
o’clock)
MINUTE Press “Set” button 5th time, LED displays “ 00 :00” twinkling,
press “ buttons to set the minutes from 00—59 (01=1 Minute, 02=2 Minute etc.)
With the “ **” light on, it means close time.
The above settings are finished for Monday Timer.
4.Press “ ” button once more, ” ” lights on, means “Tuesday”. Please note that the operations with open time HOUR/MINUTE and close time HOUR/MINUTE are the same as for Monday.
5. When Monday-Sunday timers are all set, press “ ” button on remote control 7th times to set from Monday to Sunday’s temperature and press “ ” buttons to select the temperature which you need, the temperature range is 10℃ to 49℃.
PS: In Week timer function, when you set today’s temperature, the thermostat function will start with the rules same as 4) THERMOSTAT INSTRUCTIONS.
You can set different open/close time and temperature within the whole week.
WINDOW OPEN FUNCTION
1. Turn on the appliance in fan, warm, hot mode. This function only works through remote control.
2. Press “ ” button, the “AUTO” (HC1500/HC2000/HC2050) or “ ” (HC2100/HC2500/HC3100/3200) “Auto/M” (HC2200) light is on. The appliance is working as smart saving energy models. (In this function, the appliance is checking and recording environment temperature. It will stop working, when the temperature drops 3 . The user ≧ ℃ should restart the appliance with “ON/OFF” button)
3. Press “ ” button again, the “AUTO” (HC1500/HC2000/HC2050) or “ ” (HC2100/HC2500/HC3100/3200) light is off. Window Open Function is off.
7) DELAY FUNCTION (HC1500/HC2000/HC2100/HC2500/HC3100/3200)
1. This function can be used in when:
– the appliance is in the standby state.
– before the appliance working.
– this function only works through remote control.
2. Press “ ” button, the LED light is on display, then press “ ” button one time, the “Delay” light and ”I/W” light are on. Press “ ” to set the Hours from 01-24 (01=1 o’clock, 24=24 o’clock…00=off)
———————————————————This is open time
3.Press “ ” button again, the “Delay” light and ”II/H” light are on. Press “ ” to set the Hours from 01–24 (01=1 o’clock, 24=24 o’clock…00=off)
———————————————————This is close time
PS: Press “ ” button, screen shows number that will twinkle for 5 seconds, you should operate in this time, otherwise appliance will get back to standby. (This function is one-time and must be reset after the power is cut off.)
CHILD-LOCK FUNCTION
1. This function works only through remote control. When appliance is plugged
in, this function can be used in any mode.
2. Press “ ” button one time, all lights and LED display are closed, only
“Power” light is on. In this condition, both control panel and remote control
are inactive.
3. Press “ ” button again, all lights are on and control panel and remote
control are active.
CONTROL PANEL
HC1500/HC2000/HC2050:
HC2100:
HC2200:
HC2500:
HC3100/3200:
REMOTE CONTROL HC1500/HC2000/HC2050
Remote control works with Lithium battery CR2025 3V
1. ”ON/OFF” Main power button
2. “24H” Setting timer from 1-24 hours
3. “MODE” 3 settings selection: COLD, WARM, HOT
4. “LOCK” Child-Lock function for heater
5. “AUTO” Window Open Function
6. “Delay” Set the open and closed time of heater
7. “W.Timer” Set the timer for one week
8. “+” Increase temperature
9. “-” Decrease temperature
10. “Set” Set real time
REMOTE CONTROL HC2100
Remote control works with Lithium battery CR2025 3V.
1. ”ON/OFF” Main power button
2. “24H” Setting timer from 1-24 hours
3. “MODE” 3 settings selection: COLD, WARM, HOT
4. “Swing” Louver swing up and down
5. “LOCK” Child-Lock function for heater
6. “AUTO” Window Open Function
7. “Tem.” Display room temperature
8. “Delay” Set the open and close time of heater
9. “W. Timer” Set the timer of one week
10. “+” Increase temperature
11. “-” Decrease temperature
12. “Set” Set real time
REMOTE CONTROL HC2200
Remote control works with Lithium battery CR2025 3V.
1. ”ON/OFF” Main power button
2. “24H” Setting timer from 1-24 hours
3. “MODE” 3 settings selection: COLD, WARM, HOT
4. “Swing” Louver swing up and down
5. “LOCK” Child-Lock function for heater
6. “AUTO” Window Open Function
7. “Delay” Set week temperature
8. “W. Timer” Set the timer of one week
9. “+” Increase temperature
10. “-” Decrease temperature
11. “Set” Set real time
REMOTE CONTROL HC2500
Remote control works with Lithium battery CR2025 3V.
1. ”ON/OFF” Main power button
2. “24H” Setting timer from 1-24 hours
3. “MODE” 3 settings selection: COLD, WARM, HOT
4. “Swing” Louver swing up and down
5. “LOCK” Child-Lock function for heater
6. “AUTO” Window Open Function
7. “Tem.” Display room temperature
8. “Delay” Set the open and close time of heater
9. “W.Timer” Set the timer of one week
10. “+” Increase temperature
11. “-” Decrease temperature
12. “Set” Set real time
REMOTE CONTROL HC3100/3200
Remote control works with Lithium battery CR2025 3V
1. ”ON/OFF” Main power button
2. “24H” Setting timer from 1-24 hours
3. “MODE” 3 settings selection: COLD, WARM, HOT
4. “Swing” Louver swing up and down
5. “LOCK” Child-Lock function for heater
6. “AUTO” Window Open Function
7. “Delay” Set the open and close time of heater
8. “W.Timer” Set the timer of one week
9. “+” Increase temperature
10. “-” Decrease temperature
11. “Set” Set real time
OVERHEAT PROTECTION
The heater is protected with an overheat protector that switches off the heater automatically in case of overheat. e.g. due to the total or partial obstruction of the grids. In this case, unplug the appliance, wait about 30 minutes for it to cool and remove the object which is obstructing the grids. Then switch it back on as described above.
NOTE: After switching off, the fan runs for about 30 seconds to cool down the appliance.
CLEANING AND MAINTENANCE
1. If you don’t use the heater for a long time, please wipe the surface and
put it into the box. Lay the carton on the ventilated and dry place.
2. Wait for the machine being cool and pull out the plug, then clean it. Wipe
it clean with wet washcloth or cleaner. Never directly wash with water; do not
drop the water into the machine. Never clean it with acids, chemical thinner,
gasoline, benzene etc.
3. Before use it again, please check it and make sure the outlet ventilation
have no any sundries.
TECHNICAL SPECIFICATION
Power: 2000 W
Voltage: 220-240 V ~ 50 Hz (HC1500/HC2000) / 220-240 V ~ 50/60 Hz
(HC2100/HC2200) Remote control
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>