SAHARA WB05 Clevershare Hub User Manual

June 8, 2024
SAHARA

SAHARA WB05 Clevershare Hub

SAHARA WB05 Clevershare Hub

Safety Warnings

Before using and operating this equipment, please read and observe the following precautions carefully to avoid dangerous or illegal operations.

Placement
  1. DO NOT expose the product to any heat source (such as electrical heater).
  2. Normal operating temperature is 0℃-40℃, normal operating humidity is 10%-90%RH.
  3. DO NOT place the product in dusty and humid environments in case of internal circuit fault.
  4. DO NOT expose the equipment directly to the sun, lest the equipment temperature is too high to affect the normal use of the equipment.
Power Supply
  1. Please use the standard cable of this product.
★ Water Precaution
  1. The product is not waterproof, Please keep it dry.
★ Maintenance
  1. Please contact professional service personnel for maintenance services.
  2. When the equipment is damaged, please do not disassemble it for repair without permission, please call customer service to report for repair.
  3. DO NOT insert any sharp or pointed object into the device.
  4. DO NOT drop or hit the device to avoid damage to the device.

★ Statement

  • Intellectual property right statement: The hardware design and software of this product are covered by the patents. Anyone who reproduces this product or the content of the instruction without the authorization of the Company shall assume legal liabilities.

  • This manual is for reference only, and the actual function of the final product is
    subject to the actual function of the product received by the customer.

  • The picture is for reference only, please refer to the actual product. The company reserves the right to improve and change the appearance and design of the product without notice.

Accessories

Please check for the following items in the product packing box:

  • HDMI cable×1
  • Power adapte ×1
  • Wall-mounted bracket assembly×1

Basic Troubleshooting

When the systems cannot get connect, please troubleshoot as follows:

  1. Confirm that the Wireless screens are and the Clevershare Hub are properly paired.
  2. Please check that the wireless screenshare software runs properly on your computer.
  3. Confirm that the HDMI OUT connector of the Clevershare Hub is properly connected to the HDMI IN connector of the display device.

Appearance Introduction

Please be familiar with the device interface and keys before use.

Appearance Introduction

  1. Power Button: Switch machine, rest screen, special settings, etc.
  2. Indicator Light: Display the status of the machine.
  3. LNE OUT: Audio output to the external speaker.
  4. HDMI OUT: Connect to the devices with HDMI input function.
  5. USB 3.0: Connect USB devices such as mobile hard disk, U disk, USB keyboard and mouse, USB drives, etc (output: 5VDC 0.9A).
  6. USB Type-C: Support wireless screenshare pairing, connect to peripherals (need to meet 1080p) (output: 5VDC 0.5A).
  7. LAN: Connect RJ45 terminals.
  8. DC IN: Connect DC power supply.
  9. LOCK: Lockhole.

Note: Indicator status description

① The white light is always on: startup
② The red light is always on: standby
③ White breath: breath screen
④ Red flashing: Upgrade

Operating instructions

Operating instructions

  1. Connect the HDMI OUT connector of the Clevershare Hub and the HDMI IN connector of the display device with an HDMI cable.

  2. Turn on the display device.

  3. Power the Clevershare Hub.
    Note: Support 12V power adapter and POE power supply

  4. First time use: please connect the wireless screens are to the Clevershare Hub for pairing.
    Operating instructions

  5. Connect Wireless Screens are to computer.
    Operating instructions

  6. First time use, run the Screens are program manually in your computer.
    Note: Please follow the prompt interface of the Clevershare Hub output.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and,  if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
The device for operation in the 5180 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

FCC Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement.

Canada Statement

ISED Statement This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any other.
antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

RF & Power

Frequency Range Output Power (Max.)
2402-2480(BT) <10dBm
2412-2472 <20dBm
5150-5250 <20dBm
5725-5850 <14dBm

The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals