IQxel-M8W Multi-DUT Connectivity Test System Specifications Manual
- June 8, 2024
- LitePoint
Table of Contents
- General Technical Specifications
- Wireless LAN 802.11a/b/g/n/p/j/ah/af, 802.11ac (Wi-Fi 5), 802.11ax1 (Wi-
- 802.11ax (Wi-Fi 6) Waveform Generation
- MIMO System Performance
- Navigation1
- Port Descriptions
- General and Environmental
- Order Codes
- CONTACT INFORMATION
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
IQxel-M8W Multi-DUT Connectivity Test System Specifications
General Technical Specifications
RF Analyzer
Parameter: Ports (A/B): Value
Input frequency range: RF1 to RF4: 400 to 6000 MHz
IF bandwidth: RF1 to RF4: 160 MHz
Input power range: RF1 to RF4: +30 dBm peak (+25 dBm average)
Input power accuracy: RF1 to RF4: Specification: ± 0.75 dB (+25 to -75
dBm) Typical: ± 0.50 dB (+25 to -75 dBm)
Input return loss: RF1 to RF4: > 12 dB (400 to 6000 MHz)
Spurious (signal applied)1: RF1 to RF4: < -60 dBc (CW, for signal
levels greater than -20 dBm)
Spectral flatness: RF1 to RF4: Specification: ≤ ± 1 dB ( ± 80
MHz) Typical: ± 0.50 dB ( ± 80 MHz)
Inherent spurious floor (no signal): RF1 to RF4: ≤ -80 dBm
Noise figure: – : ≤ 30 dB at minimum input attenuation
Integrated phase noise: – : ≤ 0.3 degrees (100 Hz to 1 MHz) (400 to 6000
MHz), 0.2 degrees (100 Hz to 1 MHz) typical
Signal to noise ratio: – : ≥ 55 dB 100 kHz RBW
Sampling data rate: – :10, 20, 40, 80, 160, 240 MHz
Waveform capture duration: :
at 10 MHz sampling data rate 9600 ms
at 20 MHz sampling data rate 4800 ms
at 40 MHz sampling data rate 2400 ms
at 80 MHz sampling data rate 1200 ms
at 160 MHz sampling data rate 600 ms
at 240 MHz sampling data rate 400 ms
RF Analyzer – Signal Trigger
Parameter: Range
Absolute minimum value: Wideband: RF -30 dBm, Video: -40 dBm
Absolute maximum value: Limited by the maximum input power
Trigger relative threshold: 30 dB
Level accuracy: < ± 2 dB
Port Isolation
Measurement: Description
Port to Port Isolation:
VSA-to-VSA (through path):
100 dB, <2500 MHz, typical
90 dB, >2500 MHz, typical
VSG-to-VSG (through path):
90 dB, <2500 MHz, typical
80 dB, >2500 MHz, typical
VSG-to-VSA (through and combined path):
100 dB, <2500 MHz, typical
80 dB, >2500 MHz, typical
Timebase
Measurement: Description
Oscillator type: OCXO
Frequency: 10 MHz
Initial accuracy (25°C, after 60 minute warm-up): < ± 0.05 ppm
Maximum aging: < ± 0.1 ppm per year
Temperature stability: < ±0.05 ppm over 0oC to 55°C range, referenced to
25°C
Warm-up time (to within ±0.1 ppm at 25°C): > 30 minutes
Wireless LAN 802.11a/b/g/n/p/j/ah/af, 802.11ac (Wi-Fi 5), 802.11ax1 (Wi-
Fi 6) Measurement Specifications
Measurement: Description: Performance
EVM2:
EVM averaged over payload based on standard requirements (Typical):
Residual loopback EVM (full packet channel estimation): ≤ -50.5 dB
(-2 to -15 dBm)
Residual loopback EVM (preamble only channel estimation): ≤ -47.5
dB (-2 to -15 dBm)
Residual VSA EVM (preamble only channel estimation): ≤ -48 dB (+20
to -15 dBm)
Note:
– Measured at 5755 MHz
– Averaged over 20 packets
– 802.11ax waveform, 80 MHz
Peak power: Peak power over all symbols (dBm): .
RMS power:
All: average power of complete data capture (dBm)
No gap: average power over all symbols after removal of any gap between
packets (dBm):
VSA power accuracy: ± 0.75 dB (+20 to -75 dBm).
Max avg power:
Peak value of the amplitude as a moving average over 40 samples (dBm):
VSA power accuracy: ± 0.75 dB (+20 to -75 dBm)
I/Q amplitude error: I/Q amplitude imbalance (%) and approximate contribution to EVM (dB): .
I/Q phase error:
I/Q phase imbalance (degrees) and approximate contribution to EVM (dB): .
Frequency error: Carrier frequency error (kHz): VSA measurement error: ≤ ± 0.2 ppm calibrated .
802.11ax (Wi-Fi 6) Waveform Generation
Feature: Specification
Uplink Single User OFDMA (SU-OFDMA)
Downlink Single User OFDMA (SU-OFDMA)
Uplink Multi User OFDMA (MU-OFDMA)
Downlink Multi User OFDMA (MU-OFDMA)
Multi-User MIMO + MU-OFDMA:
Up to 160 MHz
Configurable Guard Interval.
Trigger Frame Waveform Generation with configurable power levels per RU, and user configurable fields: Up to 12 dB between users
Waveform Generation with DCM (Dual Carrier Modulation) and LDPC support: .
MIMO System Performance
The additional specifications in the table below apply to the complete IQxel- M8W MIMO system.
Measurement: Range
VSA capture trigger accuracy: ≤ ± 3.5 ns
VSA start trigger accuracy: ≤ ± 3.5 ns
Navigation1
Measurement: Range
Test Capability: Carrier-to-noise ratio
Output frequency range:
_ GPS: 1575.42 MHz (fixed)
GLONASS: 1598 to 1606 MHz
COMPASS: _1561.098 (+/- 2.046) MHz
Galileo: 1559 to 1593 MHz
Number of simultaneous channels: 1
Output power range2: -60 to -95 dBm
Level accuracy: ± 0.75 dB
Port Descriptions
Front Panel
I/O: Function: Type
Power switch: Power on/off: Pushbutton switch
RF1A/RF1B: RF input/output: N female
RF2A/RF2B RF: input/output: N female
RF3A/RF3B RF: input/output: N female
RF4A/RF4B RF: input/output: N female
Power indicator: LED green – powered up, running, LED orange – powered
up, standby: LED indicator
Session active indicator: LED green – remote session active, LED red –
remote session lock: LED indicator
Status indicator: LED green – no faults/errors detected, LED orange –
Software error detected, LED red – Hardware fault detected: LED indicator
RF port 1 A/B indicator: Indicates port input/output status: LED
indicator
RF port 2 A/B indicator: Indicates port input/output status:
LED indicator
RF port 3 A/B indicator: Indicates port input/output status:
LED indicator
RF port 4 A/B indicator: Indicates port input/output status:
LED indicator
USB (2 ports): USB 2.0 compatible connection to external controller:
USB Type A
Rear Panel
General I/O
I/O: Function: Type
10 MHz ref input: 10 MHz reference input the 10 MHz reference input has a
200 ohm impedance and accepts a sine wave ranging in amplitude from 0.3 Vpp to
4 Vpp.: BNC female
10 MHz ref output 10 MHz reference output: BNC female
Marker out / trigger in 1: TTL compatible: BNC female
Marker out / trigger in 2: TTL compatible: BNC female
Marker out / trigger in 3: TTL compatible: BNC female
Marker out / trigger In 4: TTL compatible: BNC female
USB (2 ports): USB 2.0 compatible connection to external controller:
USB Type A
AC in: AC power input: 100 to 240VAC (automatically switched) 50 to 60 Hz,
Includes hard power switch
DVI port: Display Litepoint monitor: DVI-D
VGA port: Display Litepoint monitor: VGA-15 pin
Communication I/O LAN: 1000 Base-T LAN: RJ-45
GPIO: General purpose input/output: 50-pin connector
General and Environmental
Dimensions: 14.5” W x 3.2” H x 20.5” D (368 mm x 82 mm x 521 mm)
Weight: 11.4 kg (25.2 pounds)
Power requirements: 100 to 240 VAC, < 300 W, 50 to 60 Hz
Power consumption: <235 W (maximum), <10 W (standby)
Recommended PC: Intel Core i5 2.5 GHz with 4 GB of RAM or better
Recommended browser for optimal performance: Google Chrome R10 Release
Operating temperature: +10°C to +50°C (IEC EN60068-2-1, 2, 14)
Storage temperature: -20°C to +70°C (IEC EN60068-2-1, 2, 14)
Specification validity temperature1: +20°C to +35°C
Operating humidity: 15% to 95% relative humidity, non-condensing (IEC
EN60068-2-30)
EMC: EN 61326 Immunity for industrial environment, Class B emissions
Safety: IEC 61010-1, EN61010-1, UL3111-1, CAN/CSA-C22.2 No. 1010.1
Mechanical vibration: IEC 60068, IEC 61010 and MIL-T-28800D, class 5
Mechanical shock: ASTM D3332-99, Method B
Recommended calibration cycle: 12 months
Warranty: 12 months hardware, 12 months software updates
Order Codes
Code: Product
0100-IXMW-001: IQxel-M8W Test System with 8 RF ports active. Includes
WLAN measurement suite software for SISO 802.11a/b/g/n/j/p
0100-IXMW-002: IQxel-M8W Test System with 4 RF ports active.Includes WLAN
measurement suite software for SISO 802.11a/b/g/n/j/p
0300-IXMW-001: 802.11ac VHT80 (80MHz signal bandwidth) software license
0300-IXMW-057: 802.11ac VHT160 (80+80MHz and 160MHz signal bandwidth)
software license (Requires 802.11ac VHT80 license)
0300-IXMW-069: 802.11ax software license (Requires 802.11ac VHT80 license
for 80MHz signal bandwidth or 802.11ac VHT160 license for 160MHz signal
bandwidth)
0300-IXMW-061: WLAN MIMO software license. Enables MIMO option for
802.11n, 802.11ac, and 802.11ax (Requires associated 802.11 technology
license)
0150-IXMW-003: WLAN MIMO kit. Includes MIMO software license and tester
synchronization cables
0300-IXMW-003: Sequence Based Test (SBT) software license, also enables
Trigger Based Test (TBT) for 802.11ax
0300-IXMW-089: WiFi Traffic Sniffer software license (Requires 802.11ax
license)
0300-IXMW-002: Bluetooth measurement suite software license. Supports
Bluetooth 1.0 – 4.x
0300-IXMW-071: Bluetooth 5 measurement suite software license (Requires
Bluetooth 1.0 – 4.x license)
0300-IXMW-008: Zigbee measurement suite software license. Includes
measurement capability for Zigbee, Wi-SUN and Z-wave
0300-IXMW-009: DECT measurement suite software license
0300-IXMW-044: 802.11ah measurement suite software license
0300-IXMW-059: 802.11af measurement suite software license
0300-IXMW-065: Sigfox measurement suite software license
0300-IXMW-055: LTE measurement suite software license
CONTACT INFORMATION
LitePoint Corporation 575 Maude Court Sunnyvale, CA 94085-2803
United States of America +1.866.363.1911/ +1.408.456.5000
LITEPOINT TECHNICAL SUPPORT
www.litepoint.com/support
Doc: 1075-0104-001
January 2019 Rev 14
IQxel-M8W Multi-DUT Connectivity Test System Specifications Manual –
Optimized PDF
IQxel-M8W Multi-DUT Connectivity Test System Specifications Manual – Original
PDF
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>