T8 Quick Start Guide
- June 8, 2024
- Radiomaster
Table of Contents
T8
USER MANUAL
WWW.RADIOMASTERRC.COM
Introduction
Thank you for purchasing the RadioMaster T8 2.4g remote control system. The
system is powerful and versatile and can be used by beginners to
professionals. In order to ensure the correct and safe use of this product,
please read this manual carefully before use. The information contained in
this manual is subject to change without notice.
-RadioMaster team.
Safety Information
Many remote-control models are equipped with powerful motors and sharp
propellers. When using or maintaining models, proceed with caution. When
performing assembly or maintenance, make sure to disconnect the power to the
model and remove the propellers.
Do not operate the T8 remote-control system under the following conditions:
- In severe weather or strong wind conditions, such as rain, hail, snow, storms or highly electromagnetic environments.
- In any situation where visibility is limited.
- In areas where people, property, high-voltage power lines, public roads, vehicles or animals may be present.
- If you feel tired or unwell, or under the influence of drugs or alcohol.
- If the remote control or model seems to be damaged or not working properly.
- In areas with high 2.4GHz interference or where 2.4GHz radio is prohibited.
- When the battery voltage is too low.
- In areas where local regulations prohibit the use of aviation models.
Manual and firmware download
The T8 comes factory installed with special a T8 firmware for D8 and D16 use.
No firmware updates are required for this radio. Simply charge, Bind and go
fly! Visit www.radiomasterrc.com to learn about optional hardware accessories
to convert your T8 in to a T8 Pro!
Remote control overview
Charging Instructions
The T8 has a built in 1000mah 3.7v Battery. The built in USB-C charger will
charge your batteries by connecting the supplied USB-C cable to any suitable
USB power outlet. We suggest using a regular 2amp 5v USB power adapter.
Charge status and battery Level:
The 5 LEDS below the neck strap loop indicate the charging status. When the
LEDs light up from left to right the T8 is charging. Each of the 5 LEDs
indicates 20% of the battery capacity. 5 LEDs shows 100% charge, 4 LEDs 80%, 3
LEDs 60%, 2 LEDs 40%, 1 LED 20%. When the radios power is low and the T8
requires charging all 5 battery status LEDs will flash at the same time.
Please recharge the batter before using the radio any further
Using your T8
Press and hold the Power button until you feel a vibration feedback. The radio
is now on. If the throttle or switches are not in the correct position the
Power LED will be RED. Please reset the switches to the correct position and
move the throttle to the lowest point. The Power LED will turn GREEN to
indicate the radio is now ready to use. To Turn off your T8 press and hold the
power button until you feel a vibration feedback and the radio will turn off.
If the LED is RED when turning off disconnect power to your model first.
Quick Guide to Understanding the Power Button LED colors.
GREEN: Radio is starting up or turned on and working normally.
RED on start: A switch(s) or the throttle must be moved to default position.
RED on shut down: The model or receiver is still connected, disconnect power
to the model to complete the shut down cycle of the radio.
The T8 has the follow settings by default and is ready to setup with the
firmware of your flight controller or receiver up to 8 channels. The default
channel order is AETR, please set accordingly in your flight controller
software.
CH1 Aileron
CH2 Elevator
CH3 Throttle
CH4 Rudder
CH5 2 Position Switch SA
CH6 3 Position Switch SB
CH7 3 Position Switch SC
CH8 2 Position Switch SD
Binding your T8
The T8 Uses a combination of Stick inputs and then pressing the Bind button to
bind to one of the following protocols: D8 / D16 v1 FCC / D16 v1 LBT / D16 v2
FCC / D16 v2 LBT
Hold the LEFT gimbal Stick in the positions shown below then press the bind
button for more than 1 second to bind the required Protocol. The Power button
will blink blue to indicate binding is in progress.
Once a model or receiver is bound you can change between various models using
the Stick positions below and pressing the bind button for more than 1 second.
The Power button will blink blue to indicate the protocol is changing. There
is no need to put the model or receiver in bind mode again if it was
successfully bound previously.
Various different receivers and models will have different methods to place
the model or receiver in to bind mode. Please follow the instructions from the
model or receiver manufacturers user manual to initial the bind process.
A Note on input sensitivity:
If your craft feels too sensitive to input you may need to set up EXPO. EXPO
is a function to soften the stick feeling in the center of the stick
movements. This can help settle down a drone that is very sensitive to stick
movements. This is handled in the flight-controller firmware and varies
depending on the flight controller you are using and may be called EXPO or RC
EXPO. Please refer to the setup guide of your specific drone or flight
controller to set EXPO to your desired setting on the models flight control
system.
Specifications
Size: 16013045mm
Weight: 218g
Frequency: 2.400GHZ-2.480GHZ
RF Module: Multi-Protocol Module Compatible Single chip (CC2500)
Protocol Options: D8 / D16 v1 FCC / D16 v1 LBT / D16 v2 FCC / D16 v2 LBT
Transmission power: 20dbm
Antenna gain: 2db
Range: > 1km @ 20dbm (depending on the receiver)
Battery: Built in 3.7v 1000mah Lithium battery
Charging: Built in USB-C charging
Firmware: OpenTX T8 Edition (Special T8 Edition, non-configurable)
Channels: Up to 8 channels (depending on the model / receiver)
Gimbal: High-precision quad bearing potentiometer sensor gimbal
Voice support: Yes (SD Card required)
Option Accessories: 12864 LCD and OpenTX operation Clip on module
Requires Upgrading to OpenTX T8 Pro firmware
*Does not support or require OpenTX companion or user programming.
EU Simple Declaration of Conformity
RadioMaster declares the radio equipment T8/T8 Pro is in compliance with EU
directives Directive 2014/53/EU. Full text of the declaration of conformity is
available at the following website www.radiomasterrc.com Manufactured by
Shenzhen RadioMaster Co., Ltd
Address: 5/F,Building 9, De Zhi Gao Technology Park, Yang Tian Road
Bao’an District, Shenzhen, 518101, GuangDong, China
FCC ID: FCC ID: 2AV3G-T8
FCC Information
This equipment has been tested and found to comply with the limits for Part 15
of the FCC rules. This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Full text
of the declaration of conformity is available at the following website
www.radiomasterrc.com
CAUTION:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
product contains a radio transmitter with wireless technology which has been
tested and found to be compliant with the applicable regulations governing a
radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
Antenna Separation Distance
When operating your RadioMaster transmitter, please be sure to maintain a
separation distance of at least 20 cm between your body (excluding fingers,
hands, wrists, ankles and feet) and the antenna to meet RF exposure safety
requirements as determined by FCC regulations.
Follow us on Facebook
https://www.facebook.com/radiomasterrc/
Visit our website to learn more
https://www.radiomasterrc.com/
Follow us on Instagram
https://www.instagram.com/radiomasterrc/
T8 Quick Start Guide – Download [optimized]
T8 Quick Start Guide – Download
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>