ONYX Digital Kitchen Scale Manual

11lb x 0.1oz

5000g x 1g

ONYX Manual

Thank you for purchasing the American Weigh ONYX Digital Kitchen Scale. Please read all operating instructions carefully before use. Scales are precision instruments and should always be handled with proper care. To ensure years of reliable service, keep these simple tips in mind:

• Do not exceed the scales maximum capacity. Overloading your scale can permanently damage it!
• Avoid exposure to extreme heat or cold. Scales perform best at normal room temperature. If temperatures have changed dramatically, recalibration may be necessary.
• Allow your scale to warm up for 30-60 seconds before performing calibration (if available).
• Store your scale in a clean, dry location. Dust, dirt, and moisture can accumulate on the weighing sensors and electronics causing innacuracy or malfunction.
• Avoid using your scale in close proximity to strong radio wave emitting devices such as computers, cash registers, and cordless phones.
• Always weigh on a flat and level surface, free from vibrations and drafts. The corner of a room is usually the most stable.
• Gently apply all items to be weighed. Do not drop items onto the weighing platform.
• Avoid dropping your scale. The warranty does not cover damage due to rough treatment or overload.

I. Display Overview

II. Key Functions

ON/OFF/TARE button

Unit button:

III. Battery Installation

This scale should come with batteries already installed. However, you must remove the plastic insulating strip from the battery compartment before first use.

IV. Turning the Scale On and Off

To turn the scale ON, press the button

To turn the scale OFF, press and hold the button for 2 seconds.

V. Changing Weighing Units

To change the current weighing unit, press the button. The scale will cycle between g, fl.oz., lb:oz, and ml with each button press.

VI. Operating Instructions

• Place the scale on a flat and level surface.
• Press to turn the scale on.
• Place the item(s) to be weighed onto the scale.
• Observe the weight on the LCD display.

VII. Tare Weighing

To weigh using a container, the Tare feature is used. To use the Tare feature, follow these instructions:

• Place the scale on a flat and level surface.
• Press to turn the scale on.
• Place the empty container onto the scale and wait for the display to stablize.
• Press the key briefly to zero the scale. The TARE indicator will light up on the display.
• You may now add the item(s) to be weighed to the container. The display will show only the weight of the contents.

VIII. Calibration

This scale has been calibrated before shipment. However, re-calibration may be necessary from time to time. To perform calibration, follow these instructions:

• Press to turn the scale on and wait for the display to show zero.
• Tap the button 4 times and keep it held on the 4th tap.
• Release the key when the display shows the ISN number
• Tap the key again. The display will show “Zero” followed • by “0000”(±2).
• Place a 2000g weight onto the scale (not included). The • display will show “CAL1” then the ISN number.
• Now place a total of 5000g onto the scale (not • included). The LCD will show “CAL2” then “5000g”.
• Calibration is complete!

IX. Troubleshooting

Problem: The display shows:   
Solution: The scale is overloaded. Remove the excess weight.
Problem: The scale is weighing inaccurately.
Solution: Check the battery power. Lower voltage can cause inaccurate readouts. Otherwise try re-calibrating the scale. (see Section VII)

American Weigh Scales, Inc.

2 Carriage Ln, Suite 2
Charleston, SC 29407
Tel: 866-643-3444 (toll free)
Fax 843-225-7284

Read More About This Manual & Download PDF:

ONYX Digital Kitchen Scale Manual – Download [optimized]
ONYX Digital Kitchen Scale Manual – Download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>