Bissell 1887, 1887T Proheat Essential User Guide

Bissell 1887, 1887T Proheat Essential

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING YOUR APPLIANCE.
When using an electrical appliance, basic precautions should be observed, including the following:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

• Connect to a properly grounded outlet only. See grounding instructions. Do not modify the 3-prong grounded plug.
• Do not leave appliance when it is plugged in. Unplug from outlet when not in use and before servicing.
• Use indoors only.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Do not use for any purpose other than described in this user guide. Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.
• Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Turn OFF all controls before plugging or unplugging appliance.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.
• Do not use appliance in an enclosed space filled with vapors given off by oil-based paint, paint thinner, some moth-proofing substances, flammable dust, or other explosive or toxic vapors.
• Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
• Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
• Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.
• Do not use without filters in place.
• Use only BISSELL® cleaning products intended for use with this appliance to prevent internal component damage. See the Cleaning Formula section of this guide.
• Do not immerse. Use only on surfaces moistened by the cleaning process.
• Keep appliance on a level surface.
• Do not carry the appliance while in use.
• Always install float before any wet pick-up operation.
• Unplug before connecting TurboBrush® Tool.
• Plastic film can be dangerous. To avoid danger of suffocation, keep away from children.

SAVE THESE INSTRUCTIONS

THIS MODEL IS FOR HOUSEHOLD USE ONLY.
COMMERCIAL USE OF THIS UNIT VOIDS THE MANUFACTURER’S WARRANTY.

Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you aren’t sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the illustration. Make certain that the appliance is connected to an outlet having the same configuration as the plug. No plug adapter should be used with this appliance.

GROUNDING INSTRUCTIONS

This appliance must be connected to a grounded wiring system. If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electrical shock. The cord for this appliance has an equipment-grounding conductor and a grounding plug. It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

What’s in the Box?

Standard accessories may vary by model. To identify what should be included with your purchase, please refer to the “Carton Contents” list located on the carton top flap.

Assembly

1. Slide Upper Handle onto lower base and secure with two long screws (taped to Upper Handle) into marked holes.
2. Attach upper hose/cord wrap to the back of the handle by inserting hook into the slot and pressing up until it’s seated flush with the back of the machine. Use 1 short screw to secure the bottom of the wrap to the machine.
3. Attach lower hose/cord wrap by inserting the hook into the slot and pressing up until it’s seated flush with the back of the machine. Use 2 short screws to secure the bottom hose/cord wrap.
4. Wrap hose around both hose/cord wraps. Secure it by inserting the trigger hose grip into opening on the grip holder on the upper hose/cord wrap.
5. Wrap cord around lower and upper hose/cord wraps. Secure plug to cord with clip on plug.
6. Attach included tools to the appropriate storage locations on the machine (varies by model).

Cleaning Formulas

Keep plenty of BISSELL® formulas on hand so you can clean whenever it fits your schedule. Always use genuine BISSELL formulas in your machine. Other formulas may harm the machine and void the warranty. Do not use Hard Floor Formula on area rugs or carpet.

Pretreat

Pretreat spots and stains to improve carpet cleaning performance.

Boost

Add Boost carpet cleaning formula enhancers to any formula to increase its effectiveness.

WARNING:

• To reduce the risk of fi re and electric shock due to internal component damage, use only BISSELL cleaning formula intended for use with this machine.
• To reduce the risk of fi re and electric shock when cleaning a hard floor, the BISSELL bare floor tool must be used and is only to be used with BISSELL Hard Floor Solutions formula intended for use with this appliance.

Filling the 2-in-1 Water Tank

1. Use Tank Carry Handle to remove tank from the machine and bring it to the sink.
2. Pull up on the bottom edge of the latch on the tank to remove the lid.
3.  Pull up on bladder fill cover that says Fill Here
4. Fill tank with warm (60°C/140°F MAX) tap water to the water fill line. Do not boil or microwave water as it can destroy the tank.
5. Fill the provided measuring cup with formula to the fill line and pour into the bladder.
6. Push down on bladder fill cover to close.
7. Replace the tank lid and latch.
8. Place tank into machine base and seat firmly into place.

Cleaning Your Carpet

1. Plug into a proper outlet.
2. Set ReadyTools™ Dial to FLOOR CLEANING setting.
3. Use the red power pedal on the back of the machine to turn it ON.
4. Push the gray pedal to recline the machine.
5. Release trigger and make one slow forward and backward pass over same area.
6. Repeat cleaning passes until solution being suctioned up appears clean. Continue passes without pressing Spray Trigger until you can’t see any more water being suctioned up. Repeated passes will help speed up dry time.

ATTENTION:

• Take care not to run over loose objects or edges of area rugs. Stalling the brush may result in premature belt failure.
• Some Berber carpets have a tendency to fuzz with wear. Repeated strokes in the same area with an ordinary vacuum or deep cleaner may aggravate this condition.

Using the Ready Tools

1. Set ReadyTools™ Dial to TOOLS setting. This will allow spray and suction from hose.
2. Attach cleaning tool of your choice to end of hose.
3. Hold tool about 1-2 inches above soiled surface. Press Spray Trigger to apply cleaning solution. Release trigger, apply downward pressure, and pull toward you to suction up dirt and cleaning solution. Do not overwet.
4. When finished cleaning, remove and rinse tool(s) and hose in clean, running water.
5. Before wrapping the hose, lift and stretch the hose to make sure water is cleared. Wrap hose around rack.

Emptying the 2-in-1 Water Tank

1. Use Tank Carry Handle to remove tank from the machine and bring it to the sink.
2. Pull up on the bottom edge of the latch on the tank to remove the lid.
3.  Pull up on bladder fill cover that says Fill Here
4. Fill tank with warm (60°C/140°F MAX) tap water to the water fill line. Do not boil or microwave water as it can destroy the tank.
5. Fill the provided measuring cup with formula to the fill line and pour into the bladder.
6. Push down on bladder fill cover to close.
7. Replace the tank lid and latch.
8. Place tank into machine base and seat firmly into place.

After-Cleaning Care

Cleaning the Removable Nozzle

1. Grab the sides of the top of the nozzle and pull forward.
2. Rinse nozzle under running water.
3. When finished, replace nozzle by slightly raising front of machine to line up slots on each side of the base with hooks the nozzle. Push forward to click nozzle into place.

Cleaning the ReadyTools™ Dial

WARNING: To reduce the risk of electric shock, push power pedal OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

Storing Your Machine

Keep machine in a protected, dry area, like a closet or basement. Because it uses water, this machine should not be kept where there’s a danger of freezing. Freezing will damage internal components and void the warranty.

Troubleshooting

Reduced spray OR no spray

| Bladder may be empty.| Push power pedal OFF; refill bladder

with clean, warm (60°F/140°C MAX) tap water and formula.

2-in-1 Water Tank may not be seated properly.| Push power pedal OFF; remove and reseat tank.
Pump may have lost prime.| Push power pedal OFF; after 1 minute turn ON and press Spray Trigger.
Pump belt may be broken.| Push power pedal OFF and unplug from outlet. Visit support.BISSELL.com for belt replacement instructions.
DirtLifter® PowerBrush does not turn| Brush belt or pump belt is off or broken.| Push power pedal off and unplug from outlet. Visit support.BISSELL.com for belt replacement instructions.

Machine not picking up solution

| ReadyTools Dial may be on wrong setting for cleaning job.| Set dial to either FLOOR CLEANING or TOOLS setting.
Poor tool position (handheld attachments only).| Adjust angle; apply more downward pressure.
Removable Nozzle may not be properly attached.| Make sure nozzle is on correctly by slightly raising front of machine to line up slots on each side of base of machine with hooks on each side of nozzle. Attach at base first and then click nozzle into place. Refer to image 6 on page 9.
2-in-1 Water Tank lid is not properly installed.| Reinstall lid.
2-in-1 Water Tank is not properly seated.| Tank must be firmly seated to function; remove and reseat.
2-in-1 Water Tank has picked up maximum dirty water.| Empty 2-in-1 Water Tank and refill.
The lint screen may be clogged.| Clean out lint screen.

We’re Waggin’ Our Tails!
BISSELL® proudly supports BISSELL Pet Foundation® and its mission to help save homeless pets. When you buy a BISSELL product, you help save pets, too. We’re proud to design products that help make pet messes, odors and pet homelessness disappear.
Visit BISSELLsavespets.com to learn more.

Bissell 1887, 1887T Proheat Essential User Guide – Download [optimized]
Bissell 1887, 1887T Proheat Essential User Guide – Download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>