EMAG Ultrasonic Cleaner User Manual
- June 7, 2024
- EMAG
Table of Contents
ULTRASONIC CLEANER
USER MANUAL
FEATURES
Stainless steel housing, tank and lid.
Stamp tank without welding gap for better waterproof.
Cooling fan
Moisture-proofed PCB
Industrial grade IC & ultrasonic transducer
Thank you for purchasing the ultrasonic cleaner. Please take the time to read
these operating instructions before use and retain them for future reference.
Failure to follow these instructions may lead to serious personal injury and
damage to property.
ULTRASONIC PRINCIPLE
Ultrasonic cleaning is based on the cavitation effect caused by high-frequency
ultrasonic wave vibration signals in the fluid. Microscopic bubbles are
formed, and they implode violently causing cavitation which creates an
intense scrubbing action on the surface of the item being cleaned. The bubbles
are small enough to penetrate microscopic crevices, cleaning them thoroughly
and consistently.
Ultrasonic cleaning is extremely effective at removing dirt and grime which
would normally require tedious manual cleaning by hand. It has been used to
clean a wide variety of instruments and mechanical parts such as carburetors,
returning them to almost “like new” conditions without damage to delicate
parts.
PREPARATION:
1. Carefully unpack the cleaner and remove all traces of packing materials from it. Visually inspect the cleaner for any parts that may have become loose or damaged during transit.
Contents:
a: Main machine
b: Soundproof lid.
c: Power lead
d: Outlet filter
e: Mesh basket (Optional)
f: Manual
2. Place the cleaner on a flat, clean surface where the cooling fans will
receive adequate ventilation and ensure all controls are set to off. Also
ensure the drain tap is in the closed position.
3. Ensure the power lead is securely plugged into the cleaner and that no
part of the lead is likely to come into contact with moisture.
4. Carefully fill at least 1/2 of the tank with a solvent solution. For
demanding cleaning we recommend a small amount of washing up liquid, this will
help increase the cleaning performance. The cleaner is now ready for use.
Attention
a）While the machine is working normally, ultrasonic and tank syntony gives a
well-proportioned sound, and no shudder on the surface of the water, yet there
is a spray made by the tiny bubbles. If there are discontinuous surges, please
add or release a little washing solution in the tank, stopping the surges is
better for the objects cleaning.
b）On the condition of making sure the cleaning object is cleaned, please run
the machine discontinuously as far as possible(not more than 30min.),for long-
time running will cause temperature increment of the case.
SAFETY PRECAUTIONS
This unit’s voltage is :
Keep it away from children!
This device is not intended to use by individuals with restricted physical
sensory or metal capacities or those with lack of experience or knowledge,
include children unless they are supervised by an individual who is
responsible for their safety or has received training in operating the device.
Please read the following very carefully as failure to comply may invalidate your guarantee
- DO NOT run the cleaner continuously for more than one hour at a time, as doing so can damage the internal components.
- DO NOT operate the unit without fluid in the tank. Always ensure the fluid is no higher than the max mark, Always ensure there is a minimum depth of 7cm.
- DO NOT drop any item into the tank as this may cause damage to the transducer. Always place the items gently into the tank and use the basket whenever possible.
- The more items that you place in your cleaning bath the less efficient it will clean. It is not advised to overlap items. Always allow plenty of clear space between the items.
- Do keep the lid on during use. This will prevent splashes and reduce the evaporation of the fluid.
- Never immerse the machine or power cord in water or other liquid.
- DO NOT touch the power plug with wet hands, especially when inserting or removing the plug.
- DO NOT touch the unit if the machine has fallen into water during operation. Remove the power plug from the socket first.
- DO NOT disassemble the machine, except by professionals.
- UNPLUG the power source while filling or emptying the tank.
- DO NOT spray water or liquid over the device and the control panel
- DO NOT operate the cleaner without proper grounding.
- DO NOT place the device on a soft surface, where the vents could be blocked.
- Always turn the heater off after using as leaving it on can cause the fluid to evaporate and damage the internal components.
- Upon completion of the cleaning cycle, turn the heater button off and isolate the machine from the electrical supply.
- Take care when adding or removing items from the cleaning tank as the fluid is likely to be hot and displaced fluid can damage the internal components. Any displaced fluid must be dried up immediately.
- In the event of failure/emergency, disconnect the mains supply by removing the plug from the mains socket.
APPLICATIONS
This list is almost endless. Provided the product is nonporous and can normally be immersed in water almost anything can be thoroughly cleaned. Here are some examples:
- Jewelry especially gold, silver & platinum
- Watchstraps
- Coins and other collectibles
- PCB Boards etc
- Engine/Model parts
- Toothbrushes & Dentures
- Electrical components
- Make-up cases
- Diesel injection pumps
- Printer heads and toner cartridges
- Motorcycle radiators
- Vehicle differentials
- Milking parlor equipment
- Golf clubs&grips&golf balls
- Horse bits&stirrups &horse brasses
- Tattoo needles
- Surgical equipment
- Motorcycle engine crankcases
- Engine cylinder heads
- Turbochargers
- Bicycle derailleurs
- Knives, bayonets, and other militaria
- Gun and gun components
Ultrasonic cleaning is not recommended for the following gemstones: Opal,
Pearl, Emerald, Tanzanite, Malachite, Turquoise, Lapis, and Coral.
DIGITAL ULTRASONIC CLEANER STRUCTURE AND ACCESSORIES OPERATION
-
Fill stainless steel tank with liquid; Plug the cleaner into a grounded outlet; After powering on, The temperature displays the actual environment temperature, LED displays 3 minutes, which is default time.
-
Time setting: Press the “TIME-/TIME+ ”shortly at a time means time increase/reduce 1min at a time, press and hold means time will increase/reduce by 1mins continuously.
. The cleaning stops when the timer counts down to 00:00. If the unit needs to be stopped before the timer runs up, press ON/OFF button.
NOTE : Do not run the cleaner continuously for more than one hour -
Set temperature: Press “temperature-/temperature+” shortly at a time means time increase/reduce 1℃ at a time, press and hold there means time will increase/reduce by 1℃ . Usually, the best results are within 40℃ to 60℃.
-
After time and heat setting, press the ON/OFF key to start both functions. Press “Heating” button “OFF”, the heating function will stop. The same for the Ultrasonic function.
-
Empty the tank and clean both the outside and inside of the cleaner with clean and dry cloth for next use.
NOTE : Do not pour water out until it’s cooling, Hot water will hurt you and damage the machine itself.
DIFFERENT WAYS OF CLEANING
Gennral Cleaning —use only tap water. Use warm temperature about 50℃.
Enhanced Cleaning —add few drops of standard washing up liquid，liquid
soap, or detergent into the water, other non-acidic cleaning agents can also
be used.
Extensive Cleaning –removing tarnish, carbon & rust from non-plated
metals, it is recommended to use specialist cleaning solution in associated
using an ultrasonic cleaner.
WARNING : Strong acid or alkaline cleaning solution will cause corrosion, rust and even puncture of tank or machine body. To overcome this problem, dilute to mild PH solution or request for tank made of specific grade of stainless steel like SUS304.
The cleaning solution will deteriorate in effectiveness over time and use. It
is important to regularly change the fluid and carefully wash the inside of
the cleaning tank in order to preserve the effectiveness and longevity of the
cleaner. Do not use corrosive or abrasive cleaning products on the tank, which
must be wiped down and dried before it can be re-connected to the electrical
supply.
NOTE : If the machine starts to spark, smoke, smell of burnt electrics or
displays any other fault the operator must immediately stop the machine,
isolate the electrical supply and contact the supplier. Continued use is
dangerous.
Advantage
Ultrasonic is widely used throughout industries to remove difficult contaminants from the parts during or after the manufacturing process which might require a stage of cleaning before the next process. In general, if an item can be cleaned with liquid, it can be cleaned much faster and more thoroughly with an ultrasonic cleaner, Compared to traditional solvent/scrubbing methods of cleaning in a parts washer, our ultrasonic cleaners:
- Are more effective at removing contamination
- Are quicker to achieve the results you want
- Save employee time (and consequently money) by enabling ‘switch on and leave’ cleaning
- Are heated to allow cleaning solvents to work more effectively
- Use mechanical timers for simplicity, precision and longevity
- Produce less mess during use
- Less chemistry
- Reproducible result
For Better cleaning effect:
● The item should be immersed well into the water. (do not exceed the “MAX”
mark)
● Warm water( never hot or boiling) and a small amount of washing up liquid
will help increase the cleaning performance.
● Make sure there is good space around each part you put in the tank, The more
items that you place in the tank the less efficiently it will clean. It is not
advised to overlap items, If lay items one on top of the other the system
doesn’t work the way it’s supposed to.
● Basket use. Do not put items directly into the bottom of the tank, better
cleaning effect with a suitable basket. A metal basket absorbs less ultrasonic
energy at about 8%.
● Temperature: The higher temperature the better the cleaning effect. However,
when the temperature exceeds 70℃～80℃, the cleaning effect will be affected.
The best temperature we suggest is 40℃～60℃.
SPECIFICATIONS
Model
| Tank Size| Overall Size| Volume| Power| Frequ Ency|
Heating Power| Time Setting| Temper Ature
---|---|---|---|---|---|---|---|---
(LWH)mm| (LWH)mm| L| W| KHz| W| Min|
℃
PS-08A| 150×140×65| 190×170×150| 1.3| 60| 28/40| 100| 1-99| 0-80
PS-10A| 150×140×100| 190×170×195| 2| 60| 100| 1-99| 0-80
PS-20A| 240×140×100| 270×170×220| 3.2| 120| 100| 1-99| 0-80
PS-30A| 300×155×150| 330×180×280| 6.5| 180| 300| 1-99| 0-80
PS-40A| 300×240×150| 330×270×280| 10| 240| 300| 1-99| 0-80
PS-60A| 330×300×150| 360×330×280| 15| 360| 400| 1-99| 0-80
PS-80A| 500×300×150| 550×330×280| 22| 480| 500| 1-99| 0-80
PS-00A| 500×300×200| 550×330×330| 30| 600| 500| 1-99| 0-80
H: 1-99 mins can be adjustable
T: 0-80 ℃ temperature can be adjustable
D: Digital display
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>