Mophie Powerstation Flashlight User Manual

Mophie Powerstation Flashlight

IMPORTANT SAFETY INSTRUCTIONS

Warning

DANGER-CAUTION Read and understand all safety information before using this product. Failure to follow these instructions may result in electrical shock, explosion, the fire which may result in serious injuries, death, or property damage.
When used correctly, lithium-ion rechargeable batteries provide a safe and dependable source of portable power. However, if they are misused or abused, this may result in leakage, burns, fire, or explosion, causing personal injury or damage to other devices.
Misusing or incorrectly connecting the power station to a rugged flashlight may cause an electric shock to users and damage equipment.
Do not operate in explosive atmospheres such as in the presence of flammable liquids, gases, or dust.
Remove jump start clamps from vehicle battery after jump starting vehicle.
Keep the power station goes rugged flashlight dry and away from moisture and corrosive materials. The power station goes rugged flashlight should not be used near water or wet areas such as bathtubs, showers, bathrooms, sinks, swimming pools, or basements.
Do not expose the power station to a rugged flashlight to moisture, water, rain, or snow.
Keep the power station goes rugged flashlight away from heat sources, including open flames, radiators, stoves, ovens, and any other devices that produce heat.
The lithium-ion rechargeable battery used in this charging device may present a risk of fire or chemical burn if mistreated. Do not expose to fire or excessive temperature. Do not expose to heat above 212°F (100°C) or incinerate.
In the unlikely event of leakage or explosion use sand or a chemical fire extinguisher.
The power station goes rugged flashlight may become warm under extended high power operation. Do not cover, wrap, or otherwise restrict the power station go rugged flashlight during operation.
Do not disassemble the power station with go rugged flashlight. There are no user-serviceable parts inside. Incorrect reassembly may result in shock or fire hazards.
Do not drop or subject to strong impacts. Do not operate the power station go rugged flashlight if it has received a sharp blow, or has otherwise been damaged in any way.
Do not puncture, crush or subject to mechanical shock.
Only charge the power station goes rugged flashlight by the specified method with the specified charging adapter provided with the unit.
Do not use any non-mophie-branded accessories with the power station go rugged flashlight. Doing so may cause an electric shock to users and damage equipment.
The power station goes rugged flashlight, along with its accessories, are not toys and should be kept away from children.
Make sure the jumper cables are fully plugged into the jump start output before trying to jumpstart your vehicle.
Do not touch red (positive) and black (negative) jumper clamps together at any point.
Do not insert any foreign object into the pores or openings of the power station go rugged flashlight.
Do not clean the power station goes rugged flashlight with harsh chemicals, soaps, or detergents. Just wipe the case with a soft cloth.
Make sure the power station goes rugged flashlight’s charging ports do not become contaminated with lint or other debris. Use a canned-air type of product periodically to ensure that the port openings are clear.
Batteries should be recycled or disposed of as per state and local guidelines.
Storage: -4°F – 158°F (-20°C – 70°C), Discharge: -4°F – 104°F (-20°C – 40°C), Charge: 32°F – 113°F (0°C – 45°C)

SAVE THESE INSTRUCTIONS

Charging your power station go rugged flashlight IMPORTANT:

Before using the power station goes rugged flashlight for the first time, fully charge it (so that pressing any button lights up all four LEDs on the LED Battery Indicators).
To charge the power station goes rugged flashlight, connect the provided USB Wall Charger with the provided USB Type-C Cable. Next, connect the USB Wall Charger into a wall outlet; and the USB Type-C Cable tip into the power station goes rugged flashlight. The power station goes rugged flashlight will automatically begin charging. When the power station goes rugged flashlight is fully charged, all four battery indicator lights will be solid white. (This could take up to 7 hours). When fully charged, disconnect the cable.
NOTE:

• Blinking light indicates recharging. Solid lights indicate fully charged.
• The power station goes rugged flashlight is designed to charge between 32°F-113°F (0-45°C). The battery indicators will rapidly flash if the power station goes rugged flashlight is attempted to be charged outside of this temperature range.

Figure 1

Using the flashlight / work light

The LED flashlight has a low and high beam mode. Press the flashlight power ON/OFF button once to turn on low beam mode. Press the button a second time to turn on high beam mode.
Figure 2

The Work Light / Emergency Light can be turned on/off by pressing the Work Light / Emergency Light Power ON/OFF button. The first press will turn on the work light. A second press will turn on the red emergency light. The third press will turn on SOS flashing red light.
NOTE:

• The flashlight and work light will automatically turn off after 2 hours of inactivity.
• Do not look directly into the LED lights

Figure 3

Jump starting a vehicle

1. Plug the jumper cables into the jump-start output on the power station go rugged flashlight.
NOTE : Make sure the jumper cables are fully plugged into the jump-start output before trying to jump-start your vehicle.
Figure 4

2. Attach the jumper cable clamps to the vehicle battery.

• Red clamp on positive terminal (+)

• Black clamp on negative terminal (-)
  NOTE:

•  Do not touch red (positive) and black (negative) clamps together at any point. If the jump start
  button flashes red, the jumper cables have been connected incorrectly. If this flashing red condition occurs, disconnect the jumper cables from vehicle battery and restart the process from Step 1.

Figure 5

3. Press the “Jump-Start” button and wait for the solid green light.
NOTE : A flashing green light indicates safety checks are in progress.

Figure 6

Do not disconnect the jumper cables when the Jump-Start button is illuminated solid green. If you wish to cancel a jump-start attempt, simply press the Jump-Start button again and the solid green light will turn off indicating that the jump-start attempt has been canceled.

4. Start your vehicle.
NOTE : If your vehicle fails to start after the first attempt, wait 30 seconds and repeat step 3 and step 4. If your vehicle does not start after three attempts, we recommend you consult a certified mechanic.

5. Disconnect the jumper cable clamps from the car battery.
NOTE :

• The jump-start function can not be used in conjunction with USB charging. Please ensure that you have not activated the USB output when attempting to jump-start your vehicle.
• The powerstation go rugged flashlight is designed to allow a jump-start when used within a safe temperature range.
• When attempting to jump-start your vehicle, turn off your headlights and any other components that may drain your car battery.

Jumpstart troubleshooting tips

NOTE : If none of these troubleshooting tips work, please consult a certified mechanic for assistance.

Charging an electronic device using the USB output port
1. Connect the USB Type-C tip of the supplied USB Type-C Cable into the USB Type-C input of your electronic device and connect the Standard USB end of the supplied USB Type-C cable into the powerstation go rugged flashlight USB 5V/2.4A Output port.

Figure 7

2. Turn on the USB charging by pressing the USB Power ON/OFF Button on the powerstation go rugged flashlight.
NOTE:

• If your electronic device does not have a USB Type-C Input, the powerstation go rugged flashlight is also compatible with the charging cable provided with your electronic device. To use, plug the standard USB end of the cable into the 5V/2.4A USB Output port located on the powerstation go rugged flashlight.
• The powerstation go rugged flashlight USB charging feature will automatically power off after 30 minutes of inactivity.

Warranty

At mophie, we are dedicated to making the best quality products. To back this up, this product is warranted for 2 years. For full details regarding warranty terms, exclusions and limitations, please visit mophie.com/warranty. This warranty does not affect any statutory rights that you may be entitled to. Keep a copy of your purchase receipt as proof of purchase. Be sure to register your product at mophie.com.

Customer Service
Telephone: 1-888-8mophie (1-888-866-7443)
International: +1 269-743-1340
Web: www.mophie.com/cs

Specifications

• Model………………………………………………………………………….. MPSGRGD-FL36630
• Battery Pack Energy………………………………………………….. contains a 36630 mWh internal battery
• Jump-Start …………………………………………………………………. 12V/400Amps
• Input……………………………………………………………………………. 5V/2A
• USB Output………………………………………………………………… 5V/2.4A
• Dimensions………………………………………………………………… 2.85 x 10.43 inches
• Weight ………………………………………………………………………… 1.15 lbs
• Operating Temperature (During Charging) ………….. 32°F – 113°F (0°C – 45°C)
• Optimal Discharging Temperature…………………………. -4°F – 104°F (-20°C – 40°C)
• Storage Temperature Range……………………………………. -4°F – 158°F (-20°C – 70°C)

Legal

The manufacturer shall not in any way be liable to you or to any third party for any damages you or any third party may suffer as a result of use, intended or unintended, or misuse of this product in conjunction with any device or accessory other than the appropriate device for which this product is designed. Manufacturer will not be responsible for any damages you or any third party may suffer as a result of misuse of this product as outlined above. Purchaser agrees to defend, indemnify, and hold Manufacturer harmless for any claims or damages arising from unintended use or misuse, including use with an unintended device. mophie, powerstation, Stay Powerful, and the mophie logo are trademarks of mophie inc. All rights reserved. Patents: mophie.com/patents.

This device complies with part 15 of the FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAUTION: To comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC Rules, this device must be used with certified peripherals and shielded cables. All peripherals must be shielded and grounded. Operation with non-certified peripherals or non-shielded cables may result in interference to radio or reception.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

MODIFICATION: Any changes or modifications of this device could void the warranty.

WEEE DECLARATION: All of our products are marked with the WEEE symbol; this indicates that this product must NOT be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste electrical and electronic equipment by handing it over to an approved re-processor, or by returning it to mophie for reprocessing. For more information about where you can send your waste equipment for recycling, please contact mophie, inc. or one of your local distributors.

Customer Service
Telephone: 1-888-8mophie (1-888-866-7443)
International: +1 269-743-1340
Web: www.mophie.com/cs
mophie, power station, Stay Powerful, and the mophie logo are trademarks of mophie inc.
All rights reserved. Patents: mophie.com/patents. USB-C is a trademark of the USB Implementers Forum.
314-00881-A

References

• Mophie Portable Chargers & Power Banks | ZAGG
• Mophie Portable Chargers & Power Banks | ZAGG
• Mophie Portable Chargers & Power Banks | ZAGG
• Mophie Portable Chargers & Power Banks | ZAGG

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>