Noctua NH-U9DX i4 Instruction Manual
- June 7, 2024
- Noctua
Table of Contents
**Noctua NH-U9DX i4 Instruction Manual
**
Installation Manual
Dear customer,
Our DX line of coolers has become a default choice in high performance quiet
cooling solutions for Intel Xeon CPUs and the latest i4 revision supports
LGA2011 (both Square and Narrow ILM), LGA1356 and LGA1366 based Xeon
platforms. Each Noctua product is double checked for flawless operation by our
quality control team before it leaves the factory and I’m confident that you
will be able to sense some of the research, attention and care we’ve put into
making this product. Enjoy your NH-U9DX i4!
Yours sincerely,
Roland Mossig, Noctua CEO
This manual will guide you through the installation process of the SecuFirm2TM
mounting system step by step. Prior to installing the cooler, please verify
that the cooler is fully compatible with your motherboard. Should you
encounter any difficulties, please check the FAQs on our website
(www.noctua.at/faqs) and don’t hesitate to
contact our support team at support@noctua.at.
Noctua cannot be held responsible for any damage or losses caused by
compatibility issues.
Warranty, Support and FAQs
Even with high-grade products and strict quality control, the possibility of
defects cannot be eliminated entirely. Therefore, we aim at providing the
highest possible level of reliability and convenience by offering a warranty
period of 6 years and direct, fast and straightforward RMA service.
Should you encounter any problems with your Noctua cooler, please don’t
hesitate to contact our support team (support@ noctua.at).
LGA2011
There are two different types of ILM (Independent Loading Mechanism) for
Intel’s LGA2011 based Xeon CPUs: Square-ILM with 80x80mm hole spacing and
Narrow-ILM with 56x94mm hole spacing.
Square ILM
If your mainboard uses a Square-ILM, please continue as described below. If your mainboard uses a Narrow-ILM, please refer to section LGA2011 Narrow-ILM.
LGA 2011 Square-ILM
Applying thermal paste
If there are residual traces of thermal paste or thermal pads on your CPU,
please clean them off first. Then press a small drop (4-5mm diameter) of NT-H1
onto the centre of the heatspreader.
Caution :
Applying too much thermal paste will lower heat conductivity and cooling
performance!
Fastening the heatsink to the CPU
Caution: Please first take off the fan as well as the protection cover at the
bottom side of the heatsink.
Then put the heatsink onto the CPU and tighten the four springloaded screws
until they stop using the supplied screwdriver.
Caution
Tighten the screws until they stop.
Attaching the fans
Re-attach the fans to the heatsink using the steel clips:
Please make sure that both fans are aligned in the same direction.
Connect the fans to the mainboard’s CPU fan header. Note that you can use the
supplied y-cable (NA-YC1) to connect both fans to one CPU header.
Depending on your CPU and the temperature inside the case, you may
interconnect the supplied NA-RC7 Low-Noise Adapters (L.N.A.) in order to
further reduce the fans’ operating noise.
Caution:
Please use one adaptor per fan when running two fans with adaptors. Never use
one adaptor for two fans by putting it before the y-cable.
Caution:
When using the L.N.A.s, check the temperature of your CPU using appropriate
software (e.g. the respective applications of your mainboard manufacturer), in
order to evade automatic throttling of the CPU due to the increased
temperature. If the cooling performance is insufficient, please increase case
ventilation or remove the L.N.A.s.
LGA2011 Narrow-ILM
Required mounting parts:
NM-XFB4 Standard Mounting Bar
NM-XFB5 90° Mounting Bar
The LGA2011 Narrow-ILM uses a different hole spacing than Square-ILM, so
please replace the pre-installed Square-ILM mounting brackets (NM-XFB3) with
Narrow-ILM brackets (NM-XFB4 or NM-XFB5) as described below.
This manual will guide you through the installation process step by step using
the NM-XFB5 bracket as an example. Please note that the installation procedure
is identical for NM-XFB5 and NM-XFB4.
First choose the appropriate set of Narrow-ILM mounting brackets according to the desired orientation of the cooler:
NM-XF4
NM-XFB5
Unscrew the preinstalled LGA2011 Square-ILM mounting brackets
(NM-XFB3) and take them off the heatsink.
Then remove the plastic lock-rings, springs and screws from the Square-ILM
mounting brackets and put them into the Narrow-ILM mounting brackets.
After you’ve fixed the springs and screws to the appropriate Narrow-ILM
fastening brackets, please screw the brackets to the heatsink:
NM-XFB4
NM-XFB5
**LGA1356/1366
Required mounting parts:
NM-XBT2 Screws (black)**
LGA1356/1366 uses a different thread than the pre-installed screws for LGA2011
(NM-XBT1), so please change the screws as described below.
Remove the plastic lock-rings, springs and screws (NM-XBT1) from the mounting
brackets.
- NM-XBT1 (silver)
Then use the springs and the lock-rings to fix the black
LGA1356/1366 screws (NM-XBT2) to the mounting brackets.
- NM-XBT2 (black)
After you’ve fixed the springs and screws to the mounting brackets, please proceed with the steps described in section LGA2011 Square-ILM.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>