HANNLOMAX Cd/Mp3 Boombox With Radio, Usb Decoding, Usb Charging, Nfc And Bluetooth Instruction Manual

: June 7, 2024
: HANNLOMAX

Table of Contents

INSTRUCTION MANUAL
LOCATION OF CONTROLS
CD/MP3/USB OPERATION
TROUBLESHOOTING
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HANNLOMAX Cd/Mp3 Boombox With Radio, Usb Decoding, Usb Charging, Nfc And Bluetooth Instruction Manual

INSTRUCTION MANUAL

Note: Please read and follow these instructions before using your unit.

Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Grounding or Polarization This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
Alternate Warnings This product is equipped with a three-wire ground-type plug, a plug having a third (grounding) pin. This plug will only into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
The MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
CLASS II apparatus with double insulation, and no protective earth provided.
Caution Marking and rating plate was located at bottom enclosure of the apparatus.
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus.
The mains plug is used as disconnect device. The mains plug of apparatus should not be obstructed OR should be easily accessed during intended use. To be completely disconnect the power input, the mains plug or apparatus shall be disconnected from the mains.
Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
Excessive sound pressure from earphones and headphone can cause hearing loss.

FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

LOCATION OF CONTROLS

diagram, engineering drawing

1

| Speaker|

13

| BAND Switch
---|---|---|---

2

| Antenna|

14

| BASS Button

3

| FOLDER DN Button|

15

| CD Compartment

4

| FOLDER UP Button|

16

| LCD Button

5

| MODE Button|

17

| CD Door Open Button

6

| SKIP DOWN Button|

18

| AUX-IN Jack

7

| SKIP UP Button|

19

| Battery Compartment

8

| STOP/USB Button|

20

| AC Socket

9

| PLAY/PAUSE Button|

21

| Handle

10

| VOLUME Control|

22

| USB Slot (1A Charging)

11

| TUNING Control|

23

| USB Slot (Decoding)

12

| FUNCTION Switch|

24

| NFC Sensor

AC OPERATION
Before operation, please make sure that the VOLTAGE mentioned on the unit is same as the voltage of your local area. Unravel the AC power cord, insert one end into the AC socket on the set, and the other end into a standard AC outlet.
ATTENTION

Do not plug or unplug the power cable while you have wet hands.
When planning not to use this unit for a long time, disconnect the power cable from the wall outlet.
When disconnecting the power cord from the wall outlet, do not pull on the cord in order to avoid shock risks caused by damaged cable.

BATTERY OPERATION
Disconnect the AC cord set completely. Open the battery compartment door and insert 6 pieces UM-2 “C” size batteries into the battery compartment with battery polarity as shown inside the battery compartment.

USB CHARGING (1 A)
This product can provide 1A charging when it is under AC operation. You can charge most of the smartphones and tablets. Please be reminded to connect your device to the correct USB slot.

BASS EFFECT
Press BASS button for bass effect.

RADIO OPERATION

Set the FUNCTION switch to RADIO position.
Rotate the TUNING control to tune to your desired radio station.
Adjust the sound level by rotating the VOLUME control.
To turn off the radio, set the FUNCTION switch to OFF position.

FM Stereo/Mono Broadcast
For FM Mono Broadcast, set the BAND switch to FM. For FM stereo broadcast, set the BAND switch to FM ST. “ST.” will be shown on the display.

ANTENNA
For best reception, fully extend the FM Antenna to receive FM stations.

MP3/AUX IN CONNECTION

Set the FUNCTION switch to BT/AUX position.
Insert one side of the audio cable (requires 3.5mm stereo plug, not supplied) into the line-out jack or phones jack on your MP3 player and the other side to the aux-in jack on the unit.
Turn on your MP3 player and follow the playback instruction.
Adjust the sound level by rotating the VOLUME control.
To stop this function, simply turned off your MP3 player.

CD/MP3/USB OPERATION

Playing Audio CDs

Set the FUNCTION switch to CD/USB position.
Press the CD/USB button to select CD mode, CD icon will appear on the LCD display.
Insert a CD disc in the CD compartment and close the CD door, the unit will start reading the disc and will play automatically.
During playing, press the PLAY/PAUSE button to temporarily pause playing. To resume, press the PLAY/PAUSE button again.
Adjust the sound level by rotating the VOLUME control.
To stop playing the CD, press the STOP button.

Playing MP3 Discs

Set the FUNCTION switch to CD/USB position.
Press the CD/USB button to select the CD mode, MP3 icon will appear on the LCD display.
Insert a MP3 disc into the CD Compartment and close the door, the unit will start reading the disc and will play automatically.
If your MP3 disc has folders, you can use the FOLDER DN / FOLDER UP button to select the desired folder.
During playing, press the PLAY/PAUSE button to temporarily pause playing. To resume, press the PLAY/PAUSE button again.
Adjust the sound level by rotating the VOLUME control.
To stop playing the CD, press the STOP button.

Playing MP3 files with USB device

Set the FUNCTION switch to CD/USB position.
Press and hold the STOP/USB button to select the USB mode, USB will appear on the LCD display.
Plug your USB device into the USB port on the unit, the unit will start reading the files in the USB device and play automatically.
Note : Please be reminded to connect your device to the correct USB slot.
If your USB device has folders, you can use the FOLDER DN/ FOLDER UP button to select the desired folder.
During playing, press the PLAY/PAUSE button to temporarily pause playing. To resume, press the PLAY/PAUSE button again.
Adjust the sound level by rotating the VOLUME control.
To stop playing the files in the USB, press the STOP button.
Note: Because of non-standardized format definition/production of MP3 format, playback quality & performance are not guaranteed. Manufacturer is not responsible for the playability of MP3 in any case due to recording conditions such as PC performance, writing software, media ability and etc.

Different Play Mode
Press the MODE button to select different kinds of play mode with the following sequence.
For Audio CDs : Repeat 1 Repeat All Normal For MP3 Files : Repeat 1 Repeat Folder Repeat All Normal

Repeat 1 repeat the track being played.
Repeat All repeat all the tracks in the storage media.
Repeat Folder repeat the tracks in the entire folder.
Normal play the tracks in sequence.

Skip Mode

During play or pause mode, press the SKIP UP button to go to the next track.
During play or pause mode, press the SKIP DN button to go back to the previous track.

Programming
In case of Playing Audio CD/MP3 disc
The programming should be done during STOP mode

Press the MODE button, the LCD display will show P01.
Use the SKIP UP or SKIP DN button to select the desired track.
Press the PROGRAM button again to store the selected track in the memory, the LCD display will show P02 and flash continuously.
Repeat step 2 to 3 to store more tracks in the memory. You can store up to 20 tracks in the memory for CD disc and 99 tracks in the memory for MP3 disc.
Press the PLAY/PAUSE button to start playing the disc in the programmed order.
To stop playing, press the STOP/USB button.
To cancel the programming list, press the STOP/USB button and set the FUNCTION switch to OFF position.

BLUETOOTH STREAMING

Set the FUNCTION switch to BT/AUX position. The LCD display will show “bt” and the bluetooth icon will flash.
Turn on your Bluetooth of your Bluetooth device and search the boombox for connection. Your Bluetooth device should find “RCD5000”.
If the connection is successful, the bluetooth icon on the LCD display will stop flashing.
Select and play the audio files though your Bluetooth device.
To stop this function, switch to other mode or shut down your Bluetooth of your Bluetooth device..

BLUETOOTH STREAMING THROUGH NFC PAIRING

Set the FUNCTION switch to BT/AUX position. The LCD display will show “bt” and the bluetooth icon will flash.
Enable your NFC function of your Bluetooth device and place the device near the NFC sensor on the CD door for 5 to 10 seconds.
If the connection is successful, your Bluetooth device will show that it is connected and the bluetooth icon on the LCD display will stop flashing.
Select and play the audio files though your Bluetooth device.
To stop this function, switch to other mode or shut down your Bluetooth of your Bluetooth device AUTO PAIRING Once the unit paired with the Bluetooth device, it will automatically pair with that device next time when you turn on the unit and that Bluetooth device.

AUTO PAIRING
Once the unit paired with the Bluetooth device, it will automatically pair with that device next time when you turn on the unit and that Bluetooth device.