HANNLOMAX CD Boombox with Radio USB Port for MP3 Playback and Bluetooth Instruction Manual

HANNLOMAX CD Boombox with Radio USB Port for MP3 Playback and Bluetooth Instruction Manual

1. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
2. Do not use this apparatus near water.
3. Clean only with dry cloth.
4. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
5. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
6. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
7. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
8. Only use attachments/accessories specified by the manufacturer.
9. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
10. Unplug this apparatus during lightning storms or when unused for long periods of time.
11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
12. Grounding or Polarization ­ This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
13. Alternate Warnings ­ This product is equipped with a three-wire ground-type plug, a plug having a third (grounding) pin. This plug will only into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
14. Ventilation ­ Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
15. The MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
16. CLASS II apparatus with double insulation, and no protective earth provided.
17. Caution Marking and rating plate was located at bottom enclosure of the apparatus.
18. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
19. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus.
20. The mains plug is used as disconnect device. The mains plug of apparatus should not be obstructed OR should be easily accessed during intended use. To be completely disconnect the power input, the mains plug or apparatus shall be disconnected from the mains.
21. Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
22. Excessive sound pressure from earphones and headphone can cause hearing loss.

FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­
– Reorient or relocate the receiving antenna.
– ­Increase the separation between the equipment and receiver. ­
– Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.
– ­ Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

LOCATION OF CONTROLS

1. BAND button
2. PROG/MEM button
3. FOLDER/M- button
4. MODE/M+ button
5. STOP CD/USB button
6. PLAY/PAUSE button
7. SKIP-/TUN- button
8. SKIP+/TUN+ button
9. Rod antenna
10. CD Compartment
11. Carry handle
12. AUX-IN jack
13. Speaker
14. LCD display
15. FUNCTION switch
16. VOLUME control
17. Battery Compartment
18. AC socket
19. USB port for MP3 playback

AC OPERATION

Before operation, please make sure that the VOLTAGE mentioned on the unit is same as the voltage of your local area. Unravel the AC power cord, insert one end into the AC socket on the set, and the other end into a standard AC outlet.

ATTENTION

1. Do not plug or unplug the power cable while you have wet hands.
2. When planning not to use this unit for a long time, disconnect the power cable from the wall outlet.
3. When disconnecting the power cord from the wall outlet, do not pull on the cord in order to avoid shock risks caused by damaged cable.

BATTERY OPERATION

Disconnect the AC cord set completely. Open the battery compartment door and insert 8 pieces UM-2 “C” size batteries into the battery compartment with battery polarity as shown inside the battery compartment.

RADIO OPERATION

1. Set the FUNCTION switch to RADIO position.
2. Press the BAND button to select the desired AM or FM broadcasting.
3. Auto Tuning : Press and hold the SKIP+/TUN+ or SKIP-/TUN- button for approximately 1 second, it will start to search the next radio station in the direction of the search. The search operation simply finds stations with strong signals.
4. Manual Tuning: Stations with weak reception can only be tuned in manually. Press the SKIP+/TUN+ or SKIP-/TUN- button, the unit skips 0.05 MHz (FM) or 9 MHz (AM) in the direction of skip.
5. Adjust the sound level by rotating the VOLUME control.
6. To turn off the radio, set the FUNCTION switch to other position.

ANTENNA
For best reception, fully extend the FM Antenna to receive FM stations. For AM reception, the unit has a built-in antenna, turn the whole unit for best reception.

SAVING A RADIO STATION TO THE MEMORY

1. Tune the radio to the desired station.
2. Press the PROG/MEM button to store this radio station in the next memory station number. The display will show PXX (XX is the memory station number )
3. Press the FOLDER/M- or REPEAT/M+ button to select the desired station number.
4. Press the PROG/MEM button to confirm, the radio station will stored in the memory.
5. Up to 10 AM and 10 FM radio stations can be stored in the memory.

TO LISTEN TO A SAVED RADIO STATION

Press the REPEAT/M+ button or RANDOM/M- button to select the stored stations in the memory.

BLUETOOTH OPERATION

Connecting BLUETOOTH

1. Set the FUNCTION switch to BT position.

2. “ BT ” and Bluetooth logo will show in the LCD display.

3. Turn on the Bluetooth of your device and search the unit for connection. Your
   Bluetooth device should find “ HX-309CD HANNLOMAX “. (If password is needed for connection, please enter “0000”.)

4. If connection is successful, your Bluetooth device will show Bluetooth is connected. Also, the Bluetooth logo will stop flashing.

5. Select and play the audio file though your Bluetooth device.

6. During playing, press the PLAY/PAUSE button to temporarily pause playing. To resume, press the PLAY/PAUSE button again.

7. During play or pause mode, press the S KIP+/TUN+ button to go to the next track.

8. During play or pause mode, press the SKIP-/TUN- button to go to the previous track.

9. To stop this function, set the FUNCTION switch to other position.

AUTO PAIRING
Once the unit paired with the Bluetooth device, it will automatically pair with that device next time when you turn on the unit and that Bluetooth device.

CD/MP3/USB OPERATION

Playing Audio CDs

1. Set the FUNCTION switch to CD/USB/AUX position.
2. Press and hold the STOP CD/USB button to select CD mode.
3. Insert the CD disc in the CD compartment and close the CD door, the unit will start reading the disc and start playing the first track of the entire disc.
4. During playing, press the PLAY/PAUSE button to temporarily pause playing. To resume, press the PLAY/PAUSE button again.
5. Adjust the VOLUME control to the desired volume level.
6. To stop playing the CD, press the STOP CD/USB button.

Playing MP3 disc

1. Set the FUNCTION switch to CD/USB/AUX position.
2. Press and hold the STOP CD/USB button to select CD mode.
3. Insert a MP3 disc in the CD compartment and close the CD door, the unit will start reading the disc and start playing the first MP3 files on the entire disc.
4. If your MP3 disc has folders, press and hold the FOLDER/M- button, FOLDER will appear and flash on the display.
5. Press the SKIP+/TUN+ or SKIP-/TUN- button to select the desire folder.
6. During playing, press the PLAY/PAUSE button to temporarily pause playing. To resume, press the PLAY/PAUSE button again.
7. Adjust the VOLUME control to the desired volume level.
8. To stop playing the MP3 disc, press the STOP CD/USB button.

Playing MP3 files with USB device

1. Set the FUNCTION switch to CD/USB/AUX position.
2. Press and hold the STOP CD/USB button to select USB mode.
3. Plug your USB device into the USB port on the unit, the unit will start reading the files in the USB device and start playing the first track on the entire device.
4. If your USB device has folders, press and hold the FOLDER/M- button, FOLDER will appear and flash on the display.
5. Press the SKIP+/TUN+ or SKIP-/TUN- button to select the desire folder.
6. During playing, press the PLAY/PAUSE button to temporarily pause playing. To resume, press the PLAY/PAUSE button again.
7. During playing, press the PLAY/PAUSE button to temporarily pause playing. To resume, press the PLAY/PAUSE button again.
8. Press the STOP CD/USB button to stop playing.

Skip Mode

1. During play or pause mode, press the SKIP+/TUN+ button to go to the next track.
2. If the MP3 disc or storage device has folders, when the end of the folder is reached, press the SKIP+/TUN+ button will go to the first MP3 file of the next folder.
3. While playing, press the SKIP-/TUN – button twice will go to the previous track.
4. If the MP3 disc or storage device has folder, when reaching the beginning of the folder, press the SKIP-/TUN- button will go to the last file of the previous folder.

Programming the Track
The programming of the CD player should be done during STOP mode.

1. Press the PROG/MEM button, the LCD display will show P01.
2. Press the SKIP+/TUN+ or SKIP-/TUN – buttons to select the desired track.
3. Press the PROG/MEM button again to store this track in memory, the LCD display will show P02.
4. Repeat steps from 2 to 3 to store more tracks in memory.
5. For Audio CD, you can store up to 20 tracks in the memory and for MP3 files, you can store up to 99 tracks in the memory.
6. Press the PLAY/PAUSE button to play the disc in the programmed order.
7. To stop playing, press the STOP CD/USB button.
8. To cancel the programming list, press the STOP CD/USB button and open the CD door or set the FUNCTION switch to other position.

Different Play Mode
Press the MODE/M+ button to select different kinds of play mode with the following sequence.
For CDA files: Repeat One → Repeat All →   Normal
For MP3 files: Repeat One → Repeat Folder → Repeat All → Normal

• Repeat 1 ­ repeat the track being played.
• Repeat All ­ repeat all the tracks in the storage device.
• Repeat Folder ­ repeat the tracks in the entire album/folder.
• Normal ­ play the tracks in sequence.

MP3/AUX IN CONNECTION

1. Set the FUNCTION switch to CD/USB/AUX position.
2. Insert one side of the audio cable (requires 3.5mm stereo plug, not supplied) into the line-out jack or phones jack on your MP3 player and the other side to the aux-in jack on the unit.
3. Turn on your MP3 player and follow the playback instruction.
4. Adjust the VOLUME control to the desired volume level.
5. To stop this function, simply turned off your MP3 player or set the FUNCTION switch to other position.

SPECIFICATIONS

Frequency Range: AM 530 – 1600 KHz
FM 87.5 – 108 MHz
Power Supply: AC 120V ~ 60Hz
DC 12V= (UM-2 x 8 pcs)

Specifications are subject to change without further notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>