HANNLOMAX Alarm Clock Radio with Wireless QI Charger User Guide

June 7, 2024
HANNLOMAX

logo

HANNLOMAX Alarm Clock Radio with Wireless QI Charger

product

IMPORTANT SAFETY INSTRUCTIONS

  1. Read these instructions.

  2. Keep these instructions.

  3. Heed all warnings.

  4. Follow all instructions.

  5. Do not use this apparatus near water.

  6. Clean only with dry cloth.

  7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

  8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

  9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
    obsolete outlet.

  10. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

  11. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

  12. Only use attachments/accessories specified by the manufacturer.

  13. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

  14. Unplug this apparatus during lightning storms or when unused for long periods of time.

  15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
    FCC NOTICE
    This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :

    • This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

SPECIFICATIONS

Frequency Range: FM 87.5 – 108 MHz
Power Supply: AC 100-240V ~ 60/50 Hz
Rated Output DC9V / 3.5A
Backup Battery: CR2032 X 1 pc
Specifications are subject to change without prior notice.

LOCATION OF CONTROL

image 1 image 2 image 3

  1. Phone Support ( for Qi charging)
  2. STANDBY BUTTON
  3. VOL + BUTTON
  4. TIME/M+/+10 BUTTON
  5. FUNC BUTTON
  6. VOL – BUTTON
  7. ALARM ON/OFF BUTTON
  8. SNOOZE / DIMMER BUTTON / NIGHT LIGHT
  9.  FM SCAN/ BT UNPAIR Button
  10. PRESET / BUTTON
  11. SKIP+/TU+/ LIGHT + BUTTON
  12. TIME ZONE BUTTON
  13. SLEEP/TEMPERATURE BUTTON
  14. SKIP-/TU-/LIGHT- BUTTON
  15. LCD DISPLAY
  16. USB PORT FOR CHARGING (1A)
  17. Wireless Charging Status Indicator
  18. USB PORT FOR CHARGING (1A) AND PLAYBACK
  19. Speaker
  20. FM Antenna
  21. DC JACK
  22. AUX-in JACK
  23. BACKUP BATTERY COMPARTMENT
  24. TEMPERATURE SENSOR

LCD DISPLAYimage 4

CONNECTING THE UNIT TO POWER

AC OPERATION
Plug one end of the AC adaptor into the DC power Input, and then plug the other end into AC wall outlet. Before switching on the unit, make sure that the voltage of your electricity supply is the same on the rating plate.

BACK-UP BATTERY
The unit has pre-installed a CR-2032 lithium battery inside the back-up battery compartment. In case of power failure or interrupted AC power, the current time, alarm time and the stored radio stations are preserved in the memory of the unit by means of battery back-up function.

OPERATE THE CLOCK
When the clock is plugged in, the correct time will be displayed after a few seconds. (Note : The default Time Zone is set on Zone 2 – Eastern Time). The clock will automatically indicate the AM (A) or PM(P) time on the display.

SELECT THE TIME ZONE
There are 7 time zones programmed as follows:
ZONE 1 – Atlantic Time
ZONE 2 – Eastern Time (Default Setting)
ZONE 3 – Central Time
ZONE 4 – Mountain Time
ZONE 5 – Pacific Time
ZONE 6 – Yukon Time
ZONE 7 – Hawaiian Timeimage 5

CHANGE THE TIME ZONE
Make sure that the unit is in STANDBY mode. To confirm, press the STANDBY Button While the unit is in STANDBY mode, press the TIME ZONE Button, the display will show the current time zone number. Press the TIME ZONE Button repeatedly to select your time zone. When the desire time zone is selected, release the Button, the time zone will store in the memory after 1-2 seconds. When you moved to a different time zone, simply change the time zone to the new time zone, the unit will store the new time zone in the memory.

SETTING THE CLOCK AND DATEimage 6

  1. You can only set the Clock and Date when the unit is in STANDBY mode, ( When the unit is in STANDBY mode, there will be NO function modes)
  2. 12 HOURS/ 24 HOURS SETIING: Press and hold the TIME/M+/+10 Button for about 1 second, (The display will show 12HR or 24 HR )
  3. Press the SKIP+/TU+/LIGHT+ or SKIP−/TU-/LIGHT- Button to select the desired setting. Press TIME Button to confirm.
  4. After 12HR / 24 Setting, the HOUR digit will flash.
  5. Press the SKIP+/TU+/LIGHT+ or SKIP−/TU-/LIGHT- Button to adjust the hour. (In 12 HOUR setting, there will be “A” indicating AM and ‘P” indicating PM)
  6. When the hour is selected, press the TIME Button again, the MINUTE digit will begin to flash on the display.
  7. Press the SKIP+/TU+/LIGHT+ or SKIP−/TU-/LIGHT- Button to adjust the minute.
  8. When the minute is selected, press the TIME Button again, the YEAR will show on the display and flash.
  9. Press the SKIP+/TU+/LIGHT+ or SKIP−/TU-/LIGHT- Button to adjust the year.
  10. When the year is selected, press the TIME Button again, the MONTH will show on the display and flash.
  11. Press the SKIP+/TU+/LIGHT+ or SKIP−/TU-/LIGHT- Button to adjust the MONTH.
  12. When the MONTH is selected, press the TIME Button again, the DAY will show on the display and flash
  13. Press the SKIP+/TU+/LIGHT+ or SKIP−/TU-/LIGHT- Button to adjust the DAY.
  14. When the DAY is selected, press the TIME Button again. The display will back to the CLOCK display.

SETTING THE ALARMS

  1. You can set up the alarm when the unit is STANDBY mode.

  2. Press the ALARM ON/OFF Button. The display will show : ALARM ON” and the default alarm time.

  3. Press and hold the ALARM ON/OFF Button. The alarm hour will flash

  4. Press the SKIP+/TU+/LIGHT+ or SKIP−/TU-/LIGHT-Button to select the alarm hour.

  5. When the desired alarm hour is selected, press the ALARM ON/OFF Button again, the alarm minute digit will flash.

  6. Press the SKIP+/TU+/LIGHT+ or SKIP−/TU-/LIGHT- Button to select the alarm minute.

  7. When the desired alarm minute is selected, press the ALARM ON /OFF Button again, the alarm mode will flash.

  8. Press the SKIP+/TU+/LIGHT+ or SKIP−/TU-/LIGHT-Button to select the alarm modes. There are three alarm modes:
    US: Alarm wake up mode is USB **
    rA: Alarm wake up mode is FM radio
    bU Alarm wake up mode is buzzer

  9. When the desired alarm mode is selected, press the ALARM ON /OFF Button again to complete the alarm setting. The desired alarm time will remain on the display.

  10. If you want to turn off the alarm, press the ALARM ON/OFF Button. The display will show “ALARM OFF”.

    • Note: For Wake to USB, please make sure a USB device is inserted and can be properly played, otherwise the unit will default to the buzzer alarm mode automatically.

SNOOZE FUNCTION

  1. Whenever the alarm activates, it can be temporarily suspended for a short period of 9 minutes by pressing the SNOOZE/DIMMER Button once. The “ALARM ON” on the display will keep flashing.
  2. The alarm will then automatically activate again after the 9 minutes SNOOZE period has ended.
  3. This procedure can be repeated for up to approximately one hour.image 7

FUNCTION MODES

  1. Press STANDBY Button to turn on the Function mode.
  2. Press the FUNC. Button to select different function modes.
    There are four function modes:
    BLUETOOTH -> USB -> AUX-in -> FM RADIO

FM RADIO OPERATION

  1. Press STANDBY Button to turn on the Function mode.
  2. Press the FUNC. Button to select Radio mode. The display will show radio frequency.

FULL SCAN:

  1. Press the / FM SCAN/ BT UNPAIR Button to perform a full FM radio scan
    Note: When first used, your radio scanned the FM band for available stations. The station services found were then stored in your radio’s memory. You can rescan the band at anytime if you move to a different area or just refresh the stored list of available stations. The scanning process will take a few minutes.

  2. After the full scan, the radio will automatically store the first 20 FM stations as presets for instant access to your favorite stations.

  3. Use the TIME/M+/+10 Button to skip to the next stored radio station. (From station: P1 to P20).image 8

AUTO SCAN:
Press and hold the SKIP+/TU+/LIGHT+ or SKIP−/TU-/LIGHT- Button for approx.1 second, it will start to search the next radio station in the direction of the search. The search operation simply finds stations with strong signals. Stations with weak signal can only be tuned in manually.
MANUAL TUNNING
Press the SKIP+/TU+/LIGHT+ or SKIP−/TU-/LIGHT- Buttons to tune down or up the frequency by 0.1MHz.

ANTENNA
For best reception, fully extend the FM wire antenna to receive FM stations.

SAVING RADIO STATIONS IN THE MEMORY

  1. Tune to the desired stations.
  2. Press and hold the PRESET / Button for approx. 1 second, the display will show ‘PXX’ and flashing, where ‘XX’ is the next memory station number.
  3. Press the SKIP+/TU+/LIGHT+ or SKIP−/TU-/LIGHT- Button to select the desired memory station number.
  4. Press the PRESET / Button again to store the station in the memory.
  5. Repeat step 2 to 4 to store more radio stations in the memory.
  6. Up to maximum 20 FM radio stations can be stored in the memory.

SELECT A STORED RADIO STATION IN THE MEMORY

  1. Press the TIME/M+/+10 Button to select the stored radio station. (From station: P1 to P20 )
  2. Press the SKIP+/TU+/LIGHT+ or SKIP−/TU-/LIGHT- Button to select the desired memory station number.

TURN OFF THE RADIO
To turn off the radio. press STANDBY Button to return to STANDBY mode.

AUX IN CONNECTION

  1. Press STANDBY Button to turn on the Function mode.
  2. Press FUNC Button to select the AUX-in mode. The display will show “AUH”
  3. Insert one side of the audio cable (requires 3.5mm stereo plug, not supplied) into the line-out jack or phones jack on your MP3 player and the other side to the aux-in jack at the back of the unit.
  4. Turn on your MP3 player/device and follow the playback instruction.
  5. Press VOL+ Button to increase the volume. Press VOL- Button decrease the volume.
  6. To stop this function, simply turned off your MP3 player or press STANDBY Button to return to STANDBY mode.

BLUETOOTH OPERATION
Connecting BLUETOOTH

  1. Press STANDBY Button to turn on the Function mode.
  2. Press the FUNC. Button to select BLUETOOTH mode. The display will show “bT”.
  3. Turn on the Bluetooth of your device and search the unit for connection. Your Bluetooth device should find “HX-202Qi HANNLOMAX”. Select this for connection.
  4. If connection is successful, your Bluetooth device will show Bluetooth is connected.
  5. Select and play the audio file though your Bluetooth device.
  6. You can use the SKIP+/TU+/LIGHT+ Button to go to the next track or press the SKIP-/TU-/LIGHT- Button to go back to the previous track. Press the SKIP-/TU-/LIGHT- Button twice to go back to the previous track.
  7. Press the / FM SCAN/ BT UNPAIR Button to temporarily pause playing. To resume, press the / FM SCAN/ BT UNPAIR Button again.
  8. Press VOL+ Button to increase the volume. Press VOL Button to decrease the volume.image 10

Bluetooth Auto paring
Once the unit paired with the Bluetooth device, it will automatically pair with that device next time when you turn on the unit and that Bluetooth device.
Bluetooth Unpairing
To unpair the Bluetooth device, press and hold BT UNPAIR Button. The unit will start to search for a new connection.
Stop the BLUETOOTH streaming
To turn off the Bluetooth streaming, press STANDBY Button to return to STANDBY mode.

image 11

USB MP3 PLAYBACK

  1. Press STANDBY Button to turn on the Function mode.
  2. Press the FUNC. Button to select USB mode. The display will show “USb”.
  3. Plug your USB device into the USB port on the unit, the unit will start reading the files in the USB device and play automatically.
    • Please be reminded to connect your USB device to the correct USB slot
  4. Press the / FM SCAN/ BT UNPAIR Button to temporarily pause playing. To resume, press the / FM SCAN/ BT UNPAIR Button again.
  5. Press TIME/M+/+10 Button to skip 10 songs.
  6. Press VOL+ Button to increase the volume. Press VOL- Button decrease the volume
  7. To turn off the USB playback, press STANDBY Button to return to STANDBY mode.
    Note: In USB mode, the USB port for playback can only play MP3 files. It cannot charge any smart device.

SLEEP TO MUSIC FUNCTION

  1. This function allows you to listen to the function modes (radio/Bluetooth/USB/Aux) while you fall asleep.
  2. Press the SLEEP/TEMP. Button, the display will show the default sleep time of 90 minutes.
  3. Press the SLEEP/TEMP. Button repeatedly to set the desired sleep time. (The options are : 90-80-70-60-50-40-30-20-10 min. or OFF)
  4. After the pre-set time has elapsed, the unit will turn off and switch to STANDBY mode automatically.

CHARGE YOUR DEVICES/PHONES

  1. CHARGE WITH USB PORTS
    Connect the standard size end of a USB cable (not included) to the USB charging port on the unit and connect the other end to the charging port of your mobile phone or USB device,.
    The unit contains two USB ports with 5V ~ 1A charging (each port).
    Note:

    • Some devices may not support USB charging or may require a higher power rating than this product provides. Observe the charging status on your device. Ensure your device is working properly before attempting to charge. Charging function may not be supported for all phones or electronic devices
    • In USB mode, the USB port for playback can only play MP3 files. It cannot charge any smart device.
  2. WIRELESS CHARGING
    Place a supported mobile device on the phone support.
    Check the charging icon displayed on the mobile device’s screen for the charging statusimage 12

    • While charging, the Qi indicator will be RED. (Andriod Phones and Apple Phones)

    • Fully charged: the Qi indicator will be WHITE for some specific Andriod phones. For Other smart phones, the Qi indicator will stay RED.

    • Improper charging error: the Qi indicator will keep FLASHING. (Android Phones and Apple Phones)
      The wireless charger is compatible with Wireless Power Consortium (WPC) certified devices.
      Note:**

    • Do not place foreign materials, such as metal objects, magnets and magnetic stripe card between the mobile device and the wireless charger. The mobile device may not charge properly or may be damaged due to overheating.

    • Wireless charging may not work properly if you have attached a thick case to your mobile device. If your case is thick, remove it before placing your mobile device on the wireless charger.

    • If the mobile device is not placed properly on the charging surface, or depending on the location of the mobile device’s wireless charging coil, your mobile device may not charge properly.

    • When the mobile device is fully charged, remove it from the wireless charger.

DIMMER
Press the DIMMER/SNOOZE Button to adjust the brightness of the display. There will be 7 levels of brightness.image 13

TEMPERATURE
In STANDBY mode, press and hold the SLEEP/TEMP. Button to select Degree Celsius (C) or Fahrenheit (F).

image 14 NIGHT LIGHT
In STANDBY mode, press SKIP+/TU+/LIGHT+ Button to increase brightness of Night Light. Press SKIP-/TU-/LIGHT- Button to decrease to the brightness of Night Light.logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals