VOLLRATH 3872846 One Piece Cafeteria Breath Guard Installation Guide
- June 8, 2024
- VOLLRATH
Table of Contents
VOLLRATH 3872846 One Piece Cafeteria Breath Guard
Product Information
Specifications:
- Product Name: Cafeteria Breath Guard
- Model Numbers: One Piece – 2350030-01, Three Piece – 2350030-02
- Manufacturer: Vollrath Company, L.L.C.
- Material: Plastic
- Color: Clear
Product Usage Instructions
One Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figure 1.
- Repeat the above step for all four uprights.
Three Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
FAQ:
-
Q: What should I do if I encounter cracked plastic while tightening the cap nuts?
A: If you encounter cracked plastic while tightening the cap nuts, stop immediately to prevent further damage. Contact our service department for assistance at 800.628.0832. -
Q: Can I disassemble and reassemble the breath guard for cleaning purposes?
A: Yes, you can disassemble the breath guard following the reverse steps of the installation instructions for cleaning. Ensure all components are securely reassembled before use.
Breath Guard Installation
One Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE: Use caution when tightening the cap nuts. Overtightening may cause
the plastic to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
Three Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE: Use caution when tightening the cap nuts. Overtightening may cause
the plastic to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI
53081-3201
U.S.A.
Main Tel: 800.628.0830
Service Tel: 800.628.0832
FAX: 800.752.5620
Vollrath of Canada, Co.
Tel: 800.695.8560
FAX: 800.752.5620
© 2010 The Vollrath Company, L.L.C.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>