REMINGTON HC7130, HC7150 ProPower Hair Clipper User Guide

: June 3, 2024
: Remington

Table of Contents

IMPORTANT SAFEGUARDS
PARTS
GETTING STARTED
INSTRUCTIONS FOR USE
CARE FOR YOUR HAIRCLIPPER
REMOVING THE RECHARGEABLE BATTERY
RECYCLING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

REMINGTON HC7130, HC7150 ProPower Hair Clipper User Guide

Thank you for buying your new Remington® product. Please read these instructions carefully and keep them safe. Remove all packaging before use.

IMPORTANT SAFEGUARDS

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been supervised/instructed and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be done by children unless they are older than 8 and supervised. Keep the appliance and cable out of reach of children under 8 years.
Do not use this appliance near bathtubs, showers, basins or other vessels containing water.
Do not use the product with a damaged cord. A replacement can be obtained via our International Service Centres.
This product should only be used with the charging adaptor supplied.
WARNING: Keep the appliance dry.
The adaptor contains a transformer. Do not cut off the adaptor to replace it with another plug, as this causes a hazardous situation.
Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by Remington.
Do not use this product if it is not working correctly, if it has been dropped or damaged, or dropped in water.
This appliance should never be left unattended when plugged into a power outlet, except when charging.
Keep the power plug and cord away from heated surfaces.
Do not plug or unplug the appliance with wet hands.
Do not twist or kink the cable, or wrap it round the appliance.
This appliance is not intended for commercial or salon use.

PARTS

On/Off/Turbo switch
Blade set
2 attachment guide combs 1 – 21mm and 24 – 42mm, 3mm (not shown)
Blade release button
Charging indicator light
Micro USB port
Adaptor (not shown)
Slide select adjustable comb switch

GETTING STARTED

CHARGING YOUR APPLIANCE

Before using your hairclipper for the first time, charge for 14-16 hours (HC7130) and 4 hours (HC7150).
Ensure the product is switched off.
Connect the charging adaptor to the product and then to the mains.
If the product is not going to be used for an extended period time (2 – 3 months), unplug it from the mains and store.
Fully recharge your hairclipper when you would like to use it again.
Allow for 14-16 hours for a full charge for HC7130 and 4 hours for HC7150.
HC7130: when charging the LED indicator will be illuminated and will remain illuminated once the product is fully charged.
HC7150: when charging the LED indicator will be illuminated and will turn off once the product is fully charged.
To preserve the life of your batteries, let them run out every 6 months then recharge for 14-16 hours.
The HC7150 comes with a quick charge function, 10 minutes charging will give an emergency burst of run time.

CHARGING VIA STANDARD ELECTRICAL SOCKET

Ensure the product is switched off.
Connect the charging adaptor to the product and then to the mains.

USB
Connect Micro USB to the appliance, and the USB connector to any standard USB port or charger Product will only charge through USB and will not run in corded mode.

CORDED USE
Connect the charging adaptor to the product then to the mains.
CAUTION Extended mains only use will result in the reduction of the battery life.

CORDLESS USE
When the unit is switched on and fully charged, the product can be used in cordless mode for up to 60 minutes for the HC7130 and up to 75 minutes for the HC7150.

INSTRUCTIONS FOR USE

BEFORE STARTING THE CUT

Inspect the clipper making sure that it is free from hair and dirt.
Seat the person so that their head is approximately at your eye level.
Before cutting, always comb the hair so it is tangle free and dry.

TO ATTACH A COMB

Hold the comb with its teeth upward.
To attach a comb, align the legs of the comb with the holes in the top of the clipper on each side of the blade and slide the legs into the trimmer until they click.
To remove, firmly pull the comb straight up away from the clipper.

HAIR CLIPPER COMB SETTINGS

The clipper comes with two adjustable combs, a short length adjustable comb (indicated by 1-21mm on the back of the comb) and a longer length adjustable comb (indicated by 24-44mm on the back of the comb).
Please see table below for different cutting lengths available on each comb.
Shorter Length Adjustable Comb| Longer Length Adjustable Comb
---|---
1mm| 24mm
3mm| 26mm
6mm| 29mm
9mm| 32mm
12mm| 35mm
15mm| 38mm
18mm| 41mm
21mm| 44mm
On the slide select switch there is a silver indicator which, when the short length adjustable comb is on the product, shows the corresponding length setting on the left of the slide select switch. On the other side of the slide select switch there is another silver indicator which shows the corresponding length setting when the longer length adjustable comb is on the product, on the right side of the slide select switch.
To adjust the length settings, you must press the upper half of the slide select switch to release the locking mechanism, then apply force upwards on the slide select switch to increase the length setting. To decrease the length settings press the upper part of the slide select switch down and slide downwards.
Use the clipper without any fixed combs for trimming hair close to the skin.
This will trim hair to 1mm, holding the clipper so the blades are perpendicular to the skin will trim hair to 0.5mm.

INSTRUCTIONS FOR CUTTING HAIR

To turn the product On or Off slide the switch. To locate the On/Off switch please refer to the key features section.
For even cutting, allow the comb attachment/blade to cut its way through the hair. Do not force it through quickly. If you are cutting for the first time, start with the maximum comb attachment.

STEP 1 – Nape of the neck

Set the comb to 3mm or 6mm.
Hold the clipper with the blade teeth pointing upwards. Begin starting at the centre of the head at the base of the neck.
Slowly lift the clipper, working upwards and outwards through the hair, trimming just a little at a time.

STEP 2 – Back of the head

With the comb set at 12mm or 18mm, cut the hair at the back of the head.

STEP 3 – Side of the head

With the comb set at 3mm or 6mm, trim sideburns. Then change to the longer 9mm guide comb and continue to cut the top of the head.

STEP 4 – Top of the head

Use the longer length comb attachment and set it to 24mm or 27mm then cut hair on top of the head against the direction in which the hair normally grows.
For longer hair on top, use the longer length comb attachment (24 – 44mm) to achieve the desired style.
Always work from the back of the head.

STEP 5 – The finishing touches

Use the clipper without an attachment comb for close trimming around the base and sides of the neck.
To produce a clean straight line at the sideburns, reverse the hair clipper.
Place the reversed clipper at right angles to the head, tips of the blades lightly touching the skin and then work downwards.

DUAL BOOST SYSTEM (HC7150)

There is a 3 position switch on HC7150 only. First position is Off, second is normal speed, and 3 position is Boost for extra power to cut through thicker hair.
If the clipper is set to On, it will run at regular power.
If the clipper is set to Boost, it will provide maximum power.

CARE FOR YOUR HAIRCLIPPER

Your clipper is fitted with high quality blades.
To ensure long lasting performance of your clipper, clean the blades and unit regularly.
Always keep the attachment guide comb on the trimmer blade.

AFTER EACH USE

Ensure the appliance is switched off and unplugged from the mains before cleaning.
Brush the accumulated hair from the blades and body of the clipper. Do not submerge the clipper in water.
To clean unit, wipe with a damp cloth and dry immediately.
Place a few drops of cutter or sewing machine oil onto the blades. Wipe off excess oil.

WASHABLE BLADE CLEANING

To remove the blades ensure the unit is off. Press the blade release button on the back of the clipper where it meets the blade and push away from the clipper.
To reattach once the blades are cleaned and dry, align the bottom of the blade with the bottom blade housing tab and slide the cartridge back into place until you hear a click.
Do not run the entire unit under the tap, only the blade set is meant to be submerged in water.
Place a few drops of cutter or sewing machine oil onto the blades. Wipe off excess oil.

EVERY SIX MONTHS

Remove the 2 screws retaining the fixed blade with a screwdriver.
Remove the blade set.
Brush out hairs from between the blades with a soft cleaning brush. Do not remove the lubricating grease from the blades. It is not necessary to remove the small moving blade from the unit.
If the moving blade has been removed this can be re-fitted by slotting the moving blade holder over the pin in the centre of the interior product head.
The groove on the moving blade just below the teeth should rest on the plastic pressure arm which rides inside the groove. The fixed blade should be assembled with the bevelled edge of the 2 screw holes facing outward and fixed with screws.
Note that if the blades are not correctly aligned then cutting efficiency will be impaired.

CLEANING CAUTIONS

Cleaning should only be done with a soft brush, such as the brush supplied with the product.
Do not rinse under water.
Do not use harsh or corrosive cleaners on the units or their blades.
Ensure the appliance is switched off and unplug from the main outlet before cleaning.

REMOVING THE RECHARGEABLE BATTERY

We strongly recommend that a professional removes the rechargeable battery. Parts of the shaver case, and tools have sharp edges and may cause injury if not handled correctly.

The rechargeable battery must be removed from the appliance before it is scrapped.
Disconnect the charging adapter before removing the battery.
1. Ensure that the battery is fully discharged. To do this, operate the trimmer until it stops.
2. Remove the comb attachment.
3. Detach the blade cartridge.
4. Pry the decorative panel off the top housing to expose the internals and printed circuit board.
5. Unscrew the 2 screws on the big printed circuit board and 3 screws on the small printed circuit board.
6. Remove the battery and printed circuit board assembly from the battery chamber.
7. Disconnect the battery from the circuit board.
The battery must be disposed of at an appropriate official recycling/collection point.
Do not attempt to operate the trimmer once you have opened it.

RECYCLING

To avoid environmental and health problems due to hazardous substances, appliances and rechargeable and non-rechargeable batteries marked with one of these symbols must not be disposed of with unsorted municipal waste. Always dispose of electrical and electronic products and, where applicable, rechargeable and non-rechargeable batteries, at an appropriate official recycling/ collection point.

17/INT/ HC7130/HC7150 T22-0005457 Version 10 /17
Remington® is a Registered Trade Mark of Spectrum Brands,Inc.,
or one of its subsidiaries VARTA Consumer Batteries GmbH & Co. KGaA, Alfred- Krupp-Str. 9, 73479 Ellwangen, Germany
www.remington-europe.com