MerlyanBath Two Panel Bath screen Installation Guide
- June 7, 2024
- MerlyanBath
Table of Contents
MerlyanBath Two Panel Bath screen Installation Guide
Important
Please familiarise yourself with the fitting instructions before commencingfitting.
- Check that you have the tools required
- Check that the installation site is compatible with size of screen supplied
- Check all the bath screen components
- Check that the installation kit is complete
DO NOT attempt to install the product unless you can tick ALL 4 boxed as
satisfactory.
The wall plugs supplied with the installation kit are for use in solid walls.
Hollow or “stud – patrition” walls will require alternative fixings. Please
consult a hardware supplier for the correct type. It may also be necessary to
consult you tiling supplier about the correct method for drilling your tiles.
USE SAFETY EYEWEAR WHEN DRILLING
Any parts missing or damaged must be reported to your supplier within 5 days
of purchase.
Inspect fitting area before fitting. No claims will be accepted after product
had been installed.
COMPONENTS AND BOX CONTENTS
FIXING KIT COMPONENTS,TOOLS REQUIRED, SITE CONDITIONS
Fixing Kit components
pats shown are not to scale
Tools required
- Omm Masonry drill bit
- Power drill
- Quality silicone
- Pencil
- Tape measure
-
2 Philips head screw driver
- Spirit level with horizontal and vertical level indicators
IMPORTANT – Installation Site
- Ensure your bath is level before fitting.This screen is not designed to fit on baths with stepped fronts, roll top rims or integral soap dishes.
- The tiling or other wall finishing should be effectively sealed at the bath edges.
INSTALLATION
- Position the wall profile LR8387C so the seal on the moving panel A sits on the inside edge of the bath.Fig 2
- Plumb the wall profiles LR8387C using the vertical element of the spirit level. Mark 3 holes, drill with 6mm masonry bit and fit wall plugs 2SP12. Using the 3 Screw 2SY51, fix wall profiles to wall. Fig 3.
- Insert Fixed panel B into the wall profile (do not fix it to the wall profile).
- Remove the top bracket BSYS021 by loosening the screw.Insert moving panel B and reattach the top hinge bracket. Fig 3.
- Ensure the bottom seal on the moving panel A is parallel to the top surface of the bath. Drill 3 holes through the wall profile and fixed panel using a 3mm steel drill bit. Using the Screws 2SY50 and cover caps 2SS008 and clips 2SS009, fix the hinge upright to the wall profile in 3 places.Fig 4. NOTE: Only silicone the wall profile after fixing to the wall (see sealing section). Do not silicone on the back of the wall profile before fixing to the wall.
- Ensure the deflector on the seal is positioned on the inside. Make a cut on one of the bottom corners of the seal to ensure a correct fit against the hinge bracket – see circled area in. Fig 5
- To change the handing of the stabilising bar BSYS023, unscrew wherethe arm attaches to the glass clamp and reverse. Place the stabilising bar onto the fixed panel. Mark the fixing point for the bracket to the wall. Use 6mm masonry bit, insert 1 wall plug 2SP12 and fix to wall with screw 2SY51. Fasten the bracket to the glass keeping the washer on the outside of the glass. Attach cover caps to bracket. Fig 7.
- Fix the wall profile cover MOBY002L/R. FIG 8
Sealing. Fig 6
Inside (dashed line)
When installation is complete seal the joint between the wall profile and the wall, top to bottom on the inside only. DO NOT SEAL where the wall profile sits on the Bath.
Outside (full line)
From outside the screen, SEAL where the wall profile and hinge bracket sit on
the bath. Seal 50mm up where the wall profile meets the wall and where the
hinge upright and the wall profile over lap.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>