GLO-X Painting Spray Instructions
- June 7, 2024
- GLO-X
Table of Contents
- GLO-X Painting Spray Instructions
- GLO-X SPRAY PAINTING INSTRUCTIONS
- GLO-X GREEN & AQUA SPRAY PAINTS
- FOR OPTIMUM GLOW RESULTS FOLLOW THESE INSTRUCTIONS
- MOST POPULAR ITEMS CUSTOMERS PAINT
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
GLO-X Painting Spray Instructions
GLO-X SPRAY PAINTING INSTRUCTIONS
GLO-X WHITE BASE COAT
This high quality white primer, designed and manufactured to give the optimum
results for Glo-X Professional Night Paints. It is a fast drying acrylic
undercoat suitable for multiple surfaces.
If you don’t have GLO-X Base Coat you can use any good quality white base coat
purchased from your local hardware shop.
GLO-X GREEN & AQUA SPRAY PAINTS
GLO-X Professional Night Paint provides long lasting safety illumination and
is suitable for complete darkness or low light situations such as power black
outs.
The luminance effect period is dependent on intensity andthickness of paint
layer and full luminance level is best achieved in total darkness.
To recharge the luminosity, use a strong source of light to load the effect of
the paint temporarily (natural or mechanical light source eg sunlight) Simply
spray the object you wish to illuminate to enable visibility
(it is recommended that you apply over a white base coat using multiple layers
of ILLUMINATING NIGHT PAINT lacquer onto a primed surface to achieve best
result)
The luminance effect is only visible in total darkness without any light sources. Test luminosity between paint coats until the desired luminance is achieved by viewing the painted item in total darkness.
FOR OPTIMUM GLOW RESULTS FOLLOW THESE INSTRUCTIONS
The surface must be clean & dry, free from dust grease, rust & dirt. Protect adjoining surfaces from overspray. For best results apply to a white surface.
STEP 1 Clean with suitable prep wash, solvent, or detergent based cleaner.
STEP 2 Sand the surface with 400-600 grit sand paper.
STEP 3 Wipe and clean the surface area.
STEP 4 Prime the surface with an acrylic based white primer. (for the optimum
result use the Glo-X Base Coat primer)
STEP 5 Sand primer with 400-600 grit paper.
STEP 6 Wipe and clean the surface area.
STEP 7 VERY IMPORTANT – Shake the glow can for at least 3 minutes until you
hear the mixing ball rattling freely. All the good stuff is at the base of the
can so it’s critical to follow this step. When spraying it comes out clear and
only goes green or aqua when in total darkness.
STEP 8 Spray in thin light coats, cover the surface in several even passes,
allow to dry (time to dry will be affected by temperature. humidity and sub-
surface)
STEP 9 Apply further coats in the same fashion as step 8 until you reach the
desired amount of glow. We recommend 3-4 light coats.
STEP 10 When dry a clear coat of acrylic or 2-pac paint may by applied.
Re-coating: Any time after 20 minutes. Coverage: Up to 2m2 per can, depending
on surface and colour used. Drying: Touch dry in less than 20 minutes under
normal conditions.
After spraying: Prevent blocking by turning the can upside down and spraying
until clear gas emerges. Also wipe the nozzle clean. Clean
MOST POPULAR ITEMS CUSTOMERS PAINT
- Skateboards
- Bikes
- Helmets
- Motorbikes
- Fishing lures & sinkers
- Hard safety marking
- Night Guidance
- Post Marking
- Wheel Rims
- Outdoor Steps
- Tent Pegs
- Caravan Steps
You can literally paint anything in GLO-X Paints but the key to making it work is the base colour before applying the glow paint must be white. If base colour is black, red , green , blue or any other colour its essential to use a base coat of white before you apply the glow paint. If you don’t follow that instruction the product will not glow to its optimum level.
DO’S
Apply white base coat to all non-white products
Shake the can for at least 3 minutes before painting
Apply at least 3 glow coats
At night place in total darkness for optimum glow
DON’TS
Don’t paint directly onto a coloured object without applying a white base coat
Don’t place the object in lite up areas at night as it’s is called glow in the
dark not glow in ambient lighting.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>