WUNDA 170524 Smart Connection Box Instruction Manual
- June 12, 2024
- WUNDA
Table of Contents
WUNDA 170524 Smart Connection Box
Welcome to your Smart Connection Box
- Status Lights
- Setup Pairing Button
- Output Test Button
- 5A Fuse
- Terminal Blocks
- Wire Clamping Area
- Actuator Cable Channel
- DIN Mounting Rail Clamp
- Wall Fixing Holes
- Antenna
Quick Install Guide
A. First ensure your choice of Hub is set up and your App is installed.
B. Mount Connection Box near manifold
C. Connect actuators to terminal
D. Connect power, pump and heating source
E. Launch your App and choose Devices , then Add device and choose
Smart Connection Box.
F. Hold the Setup Button and wait until it shows the device has been
successfully paired.
G. Configure Your installation in App
For more information please visit:
www.wundasmart.com/support
Technical Specification
Dimension | 326 × 133 × 32 mm |
---|---|
Weight | 490 g |
Power Supply | 230V~ 50Hz |
Mounting: | DIN rail 35mm |
Wiring | Fixed wiring only |
Fuse: | 5A |
Switch Rating | 2(1)A 230V~ |
Pump circuit load: | 2(1)A 230V~ |
Thermoelectric actuatir circuit load | load: 12x 230V~ 50Hz/20W max |
Ingress Protection: | 0°C to 45°C |
Storage Temperature | -10°C to 55°C |
Ambient Humidity | Operating 25% to 90%, Storage 15% to 95% (non-condensing) |
Software Class | A |
Rated Impulse Voltage | 2.5kV |
Radio SRD Frequency | 869.85 MHz |
Radio SRD Bandwidth | 125 kHz |
Radio SRD Maximum Power | <5 dBm |
EU Declaration of Conformity
This device is in compliance with essential requirements and other relevant provisions of the following EU Directives:
- RED Directive 2014/53/EU
- RoHS Directive 2011/65/EU
A copy of the EU declaration of Conformity is available at: wundasmart.com/conformity
Precautions
- Installation and connection should be carried out by technical service or authorized and qualified persons according to applicable regulations and standards.
- Always disconnect the power supply when connecting or d is connecting the devices powered from the main device.
- Before the installation, read the terms and conditions of the warranty and these instructions. Improper installation or use against these instructions will void the warranty.
- Al l repairs to the device should be carried out by a competent electrician. Otherwise, it will void the warranty.
- This device should not be installed or worked on by minors, people with reduced physical or mental abilities or with lack of experience or knowledge of the equipment, except if supervision and instruction for the safe use of the equipment is provided in such a manner that a ll the associated hazards a re understood.
- If a power cord is damaged, it should be replaced by a qualified person in order to avoid a hazard.
- Do not install the device with mechanically damaged casing or damaged/broken cables.
- The device must not be exposed to water or excessive humidity resulting in steam condensation (e.g. caused by rapid changes of the ambient temperature).
The WEEE symbol means that a device must 5;e disposed of separately from general household waste. When a device reaches the end of its life- span, it must be taken to a designated waste collection point for safe disposal or recycling.
This conserves natural resources, protects human health and helps the environment.
Manufacturer
Wunda Group PLC Caldicot, NP265AD United Kingdom
www.wundasmart.com
Heating Source – Voltage Free (Wiring example)
Heating Source – 230V-Output (Wiring example)
If you are wiring your two port valve or direct feed to trigger the boiler to
the connection box, ensure that you select the relay within the app when you
are selecting your actuators.
CUSTOMER SUPPORT
Need our help?
Our designated support staff are on hand to answer all your questions
help@wundasmart.com
0800 083 2677
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>