FOGEEK Apollo Headphone Instruction Manual
- June 7, 2024
- FOGEEK
Table of Contents
FOGEEK Apollo Headphone Instruction Manual
C.Headset parameters
Wireless mode Version: CSR 4.1
Receiving distance: 10m Pairing password: 0000 Signal to noise ratio: -92dBm
Carrier frequency: 2402MHz-2 80MHz Transmit power: 4dBm (maximum) Support
agreement: HFPVI.6,HSPV1.2, A2DPV1.2,AVRCPV1.0,DIV1.3 Working
time:10H(Bluetooth+ANC) 30H(ANC) 30H(Bluetooth) Charge time : 3.5- 4 H battery
capacity: 600mAh
D.Noise
reduction function description The noise cancelling circuit senses external noise through the built-in microphone and
A. produce labeling
O Microphone ‘f 0 3.5mm Audio jack O Noise Reduction Switch 0 Charging Socket O “+” key: volume up/next song O Bluetooth switch O “2 key: Volume down /previous song (;) Bluetooth connection status indicator, charging status indicator ANC status indicator sends unit itself equal and opposite cancellation signals.
- The noise cancelling effect may not be noticeable in a very quiet environment, or you may hear little noise.
- The noise cancelling effect may vary depending on how you wear the unit, or buzzing (squeaking) may occur. In this case, remove the unit and then wear it again.
- The noise cancelling function is mainly effective for the low-frequency noise. The noise can be reduced, but it can not be completely eliminated.
- The mobile phone may cause interference and noise to the unit. If this happens, take the unit away from the mobile phone.
- Do not cover the microphone of this unit with your hand, the noise cancelling function may not function properly, or buzzing may occur (squeak). E.About Bluetooth communication
- Bluetooth wireless technology operates within a range of approximately 10m and may vary.
B. Introduction to functions
1.Noise reduction and Noise reduction Shutdown
- Turn on: When the noise reduction function is off, turn the noise reduction switch on then the noise reduction indicator will on.
- Turn off: When the noise reduction function is enabled, turn the noise reduction switch on then the noise reduction indicator will off.
2.Bluetooth and Bluetooth shutdown
- Turn on: Turn off the power, long press the power button, voice prompt “Power on”, the blue light will flash. • Turn off: In power-on state, press and hold the power key, the voice prompt “Power off’, the red indicator light will blink.
3 .Matching cell phones or other bluetooth products
-
In shutdown mode, press and hold the Bluetooth switch key for 3 seconds until the red and blue lights flicking, there is voice”ready to pair”.
depending on the obstacles (body, metal, wall, etc.)or the electromagnetic environment. -
Bluetooth communication may be interrupted, noise or audio loss may occur under the following conditions:
– There is someone between the unit and the bluetooth device. – There are obstacles such as metal or wall between the unit and the bluetooth device.
– There are devices working on 2.4GHz frequency near this unit, such as WI-FI devices, cordless phones, or microwaves. -
Because bluetooth devices and WI-FI work on the same frequency (2.4GHz), microwave interference may occur if this unit is used near a WI-FI device, causing noise or audio loss or communication interruption. In this case, do as followings:
– Use the unit at least 10m away from the WI-FI device.
– If you use this unit within 10m from the WI-FI device, turn off the WI-FI device.
The headset will enter pairing mode.(If the power button is released before the red and blue lights flicking, the headset enters shutdown mode, you need to shut down and re-operate the headphone.) -
Turn on the Bluetooth switch of your phone or other bluetooth product.
-
Search Bluetooth pairing name ” Apollo 1 ” and click “connect”.
-
The Bluetooth connection status indicator is flashing blue slowly with a success pairing tone.
– Place the unit and bluetooth device as close as possible to each other. -
The microwave emitted from the bluetooth device may affect the operation of the electronic medical device. In the following places, please turn off this unit and other bluetooth devices, or it may cause an accident. -The places store flammable gases(hospital or gas station). – Near automatic doors or fire alarm bell – Always use the 3.5mm jack cable when using this unit on airplane.
-
Due to the nature of wireless technology, the sound played on this unit delays after sounds and music played on the sending device. As a result, images and sounds may not be synchronized when watching movies or playing games. • We assume no responsibility for any disclosure of information during the bluetooth communication.
-
The headset memorizes the current device and it will pair automatically for the second time.
4.Music player
- Press the Bluetooth switch to play music.
- Press the Bluetooth switch button to stop playing.
- Press the “+” key to turn the volume up.
- Press and hold the “+” key to switch to the next song.
- Press the “– key to turn the volume down.
- Press and hold “-” button to switch to the previous song.
5.Call
- When you call, press the Bluetooth key to answer the call by headphone.
- When the call is finished, short press the Bluetooth key to end the call.
- When you reject a call,long press the Bluetooth key to reject current call
- When the last number is redialled, double tap the Bluetooth key to call back the last call number on the phone.
- The connection to all bluetooth devices can not be guaranteed.
F. About charging this unit
- Do not turn on the unit or use bluetooth or noise cancelling while the unit is charging.
- If the unit is not used for a long time, the rechargeable battery may not be able to retain enough power. After repeated charge and discharge several times, the battery will be able to maintain the appropriate power
- If you store the unit for an extended period of time, charge the battery every six months to prevent over-discharge.
6. Charge
- When the headset indicates a low battery, turn off the headset and charge it.
- Connect the USB charging port, adapter 5V power supply.
- Connect the headphone charging jack. • When charging: Charging indicator is red.
- Charging completed: Charging light is off.
7.Wired function
- No noise reduction function In shutdown mode, put audio cable into the headphone jack at one end, and put the other end into the phone or other product’s audio output port.
- With noise reduction function Open the noise reduction switch, put audio cable into the headphone jack at one end, and put the other end into the phone or other product’s audio output port.
- In the wired state, the music playing is controlled by the data output part.