JAM TWS EXEC HX-EP625 Earbuds Instructions

: June 7, 2024
: JAM

Table of Contents

JAM TWS Exec HX-EP625 Instruction Book
Read User Manual Online (PDF format)
Download This Manual (PDF format)

JAM TWS Exec HX-EP625 Instruction Book

CONTROLS

A – Touch controls (Power on/off / Play / Pause / Forward / Backward)
B – Earbud status light
C – Earbud charging contacts
D – USB charging port – to charge the portable case
E – Microphones (there are two on each earbud)

SET UP

CHARGING YOUR EARBUDS

CHARGING YOUR EARBUDS

To charge your earbuds, place them into the portable case. The red LEDs on the earbuds show that they are charging. If the red LEDs do not appear when placed in the case, adjust the earbuds to make sure they are in line with the charging contacts. When fully charged, the LEDs will shut off. It will take approximately 2 hours to charge.

CHARGING YOUR PORTABLE CASE

CHARGING YOUR PORTABLE CASE

Plug the small end of the USB cable into the micro USB port, located on the back of the case. The LEDs on the case will flash blue while charging. When the portable case is fully charged, the four LED lights will remain on. Once the USB cord is unplugged, the lights will turn off.

CONNECT BOTH EARBUDS

STEP 1

STEP 1 – TURNING ON THE EARBUDS

Your earbuds will automatically turn on when taken out of the portable charging case. If you need to turn them on manually, yo u can press and hold the touch sensor for 5 seconds on both earbuds.

STEP 2 – CONNECTING THE EARBUDS TO EACH OTHER

When you take the earbuds out of their case, they will automatically sync to each other. The LEDs on the left earbud will flash blue and red alternatively. You will also hear a series of tones. Your earbuds are now in pairing mode and searching for a Bluetooth® device to connect to.

STEP 2

If your earbuds don’t sync to each other automatically, tap both earbuds two times at the same time on the touch sensors. This will put your earbuds into sync mode, and the LEDS will flash blue and red alternatively. Your earbuds should now be connected and are in pairing mode and searching for a Bluetooth device to connect to.

STEP 3

STEP 3 – CONNECTING TO A DEVICE

Enable Bluetooth® on your device. From the Bluetooth® menu, select “JAM TWS Exec”. When the device and TWS Exec are connected, you will hear a tone and the LEDs on the earbuds will slow flash blue. This means the pairing is complete.

To disconnect from all connected device and reset pairing, place both earbuds in the charging case and quickly tap the touch sensors on both earbuds 3 times, at the same time. The LEDs will flash purple 3 times. Your earbuds are now disconnected from the previously connected device and will need to be paired again before using.

CONNECT 1 EARBUD

Use the left or the right earbud independently. This is a great option if you want to hear your surroundings as well as your music.

STEP 1 – TURNING ON THE EARBUD

STEP 1 – TURNING ON THE EARBUD

Your earbud will automatically turn on when taken out of the portable charging case. If you need to turn it on manually, you can press and hold the touch sensor for 5 seconds on the earbud.

STEP 2 – PAIRING MODE

STEP 2 – PAIRING MODE

Once a single earbud is taken out of the case or manually turned on, it should enter into pairing mode. The LED will flash red and blue and you will hear a series of tones. This will indicate your earbud is in pairing mode. If it does not enter pairing mode automatically, place the earbud back in the charging case for 2 seconds and then remove it again to enter pairing mode.

STEP 3 – CONNECTING TO A DEVICE

STEP 3 – CONNECTING TO A DEVICE

Enable Bluetooth® on your device. From the Bluetooth® menu, select “JAM TWS Exec”. When the device and TWS Exec are connected, you will hear a tone and LED will slow flash blue. This means the pairing is complete.

TURNING OFF YOUR EARBUDS

STEP 2 – PAIRING MODE

To turn off your earbuds, place your earbuds back in your case, or press and hold the touch sensors on both earbuds for 5 seconds. We recommend keeping your earbuds in the charging case when not in use.

USING YOUR PORTABLE CHARGING CASE

With a full charge, your portable charging case will give your earbuds 25 extra hours, giving you up to 32 hours total of listening time.

LED INDICATORS

TROUBLESHOOTING

Disconnect and forget the TWS Exec on your Bluetooth® device. Please view the device instruction manual for instructions on how to forget a device.
Turn off Bluetooth® on your device.
Make sure earbuds are in the charging case.
Quickly tap the touch sensors on both earbuds 3 times, at the same time. This will reset your earbuds.
Remove both earbuds from the charging case.
Earbuds will automatically go into pairing mode once they are taken out of the case. The LED on the left earbud will flash red and blue alternatively. This means they are ready to pair.
Turn on Bluetooth® on your device.
Pair to “JAM TWS Exec”
Earbuds not disconnecting from your device? The TWS Exec earbuds may automatically connect to your device if put in a charging case that has no battery left. For the best experience, periodically charge the case to ensure it always has battery life.

BASIC FUNCTIONS

MUSIC

CALLS - OTHERS

LEGAL INFORMATION

READ ALL INSTRUCTIONS BEFORE USE AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

FCC Warning:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Any changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

FCC RF Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISEDC Caution:

This device complies with Innovation, Science, and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

ISEDC RF Exposure Statement:

The device is in compliance with RF exposure guidelines; users can obtain Canadian information on RF exposure and compliance.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING.

WARNING: Do not place speakers too close to ears. May cause damage to ear drums, especially in young children.

Use this product only for its intended purpose as described in this manual. Do not use attachments not recommended by JAM.
JAM is not liable for any damage caused to smartphones, iPod/MP3 players, or any other devices.
Do not place or store this product where it can fall or be dropped into a tub or sink without shutting waterproof doors.
Do not place or drop into water or any other liquid without shutting waterproof doors.
Not for use by children.
THIS IS NOT A TOY.
Never operate this product if it has a damaged cord, plug, cable, or housing.
Keep away from heated surfaces.
Only set on dry surface. Do not place on surface wet from water or cleaning solvents if waterproof doors are open.

WARNING: This product has an internal, non-replaceable lithium battery. Please dispose in accordance with your local, state, province, and country guidelines. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire, or the like.

BATTERY REPLACEMENT

Your speaker includes a rechargeable battery designed to last the lifetime of the product. In the unlikely event that you should require a replacement battery, please contact Consumer Relations, which will supply details of the warranty and out-of-warranty replacement battery service. This product contains small parts that may present a choking hazard for young children.

CAUTION: All servicing of this product must be performed by authorized JAM Audio service personnel only. For complete user guide and to register your product, visit www.JAMaudio.com (USA), canada.jamaudio.com (Canada), or uk.jamaudio.com/instructionbooks (UK).

To prevent possible hearing damage, do not listen at high volume for long periods.

WEEE EXPLANATION

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.

BATTERY DIRECTIVE

This symbol indicates that batteries must not be disposed of in the domestic waste as they contain substances that can be damaging to the environment and health. Please dispose of batteries in designated collection points.

Hereby, FKA Brands Ltd, declares that this radio device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. A copy of the Declaration of Conformity can be obtained from uk.JAMaudio.com/DoC.

© 2020 HMDX. All rights reserved. JAM is a registered trademark of HMDX. HMDX is a registered trademark of FKA Distributing Co. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc. and any use of such marks by HMDX is under license.

Operating frequency band: 2402 – 2480MHz
HX-EP625: Maximum radio-frequency power transmitted: maximum radio-frequency power transmitted 1.02 dBm

Distributed by HMDX.
3000 N Pontiac Trail
Commerce Township, MI 48390

All rights reserved.
IB-HXEP625