VWR INTERNATIONAL DS-500 Orbital Shaker Instruction Manual

**Instruction Manual

**

PACKAGE CONTENTS

Orbital Shaker
Instruction manual
Non-skid rubber mat
Power Cord

CARE AND HANDLING

Upon receiving your Orbital Shaker, check the outside packaging to ensure that no damage has occurred in shipment. If damage is noticed, notify the carrier immediately and file a shipping claim.

MAINTENANCE &  SERVICING

Your Orbital Shaker is built for long, trouble-free, dependable service. No lubrication or other technical user-maintenance is required. However, at least every three months you should:

• UNPLUG THE UNIT
• Remove any accumulated dirt from the base and platform
• Check all controls and accessible items to make sure they are properly tightened
• Tighten any item that is loose

ENVIRONMENTAL CONDITIONS

Non-Operating Storage:
Temperature: -20 to 65 º C (-4 to 149º  F)
Humidity: 20% to 85% RH, non-condensing
Operating Conditions: Indoor use only Temperature: 10 to 40 ºC (50 to 104º F)
Humidity: 20% to 85% RH, non-condensing
Altitude: 0 to 6,562 ft. (2000M) above sea level
Installation Category II and pollution degree 2 in accordance withIEC 664

SAFETY INSTRUCTIONS

Warning
Do not use Orbital Shaker in a hazardous atmosphere or with hazardous materials for which the unit was not designed. Also, the user should be aware that the protection provided by the equipment might be impaired if used with accessories not provided or recommended by manu- facturer, or used in a manner not specified by the manufacturer.
Warning
Wipe up spills immediately to prevent electrical shock. Unplug from power before cleaning and do not operate until clean up is complete.
DO NOT immerse.
Warning
Do not operate the unit if it shows signs of electrical or mechanical damage.

OS-500 Orbital Shaker

Weight Capacity: approx. 35 lbs (16kg) at 75 rpm approx. 5 lbs (2.3kg) at 500 rpm
Orbit: .75″ (1.9cm) Speed Range:25 to 500 rpm
Operating Temp: 4 º C to 40 ºC
Voltage:120 volts AC, 50/60 hertz 230 volts AC, 50/60 hertz
Current:Less than 1 amp
Fuses:120v – 2 – 5 amp 5 x 20mm quick acting
230v – 2 – 5 amp 5 x 20mm quick acting
Power:120 watts
Controls:On/Off Switch Speed Knob, variable 1 to 10 markings Timer Knob, variable 1 to 10 markings
Timer: Timer runs from 1 to 120 minutes
Dimensions: 7¼”H x 10″W x 15″D (18.0cmH x 27.3cmW x 38cmD)
Ship weight:50 lbs (23kg)

INTRODUCTION
The 120v and 230v units are supplied with a 3-prong power cord that should be plugged into a standard 3-prong grounded outlet. If the cord supplied does not meet your needs, please use an approved power cord that suits local codes and electrical supply.

OPERAT INGINSTRUCTIONS

1. Please familiarize yourself with the features and operation completely before operating the unit.
2. Be sure the power switch is in the standby position. On the 230v shaker, an additional “Power Switch” is located on the back of the unit. This switch should be in the off position.
3. Plug the cord into a properly grounded three pronged outlet.
4. Your Orbital Shaker is ready for use.
5. If this is the first time use for this unit, be sure the speed knob and timer knob are set to the off position.
6. To run in continuous mode, push rocker switch to the run position. Slowly turn speed control knob to desired speed. Unit will run until you move rocker switch to the standby position. When the test is complete, press the rocker switch to the standby position. To start the next test, begin by turning the speed knob to the 1 position.
7. To run in timed mode, set timer to desired time. Turn the speed knob to the 1 position. Press the rocker to the timed position and release. Slowly turn speed knob to desired speed, the shaker will run for the set time.

OPERATION NOTES:
Two 5 amp fuses prevent damage to the motor or electronics.
The Orbital Shaker is designed to be balanced with the standard platform attached (platform weight is 3 lbs). At higher speeds, 200rpm and above, the shaker should be run with this weight as a minimum, on stable surface, for maximum stability.

DS-500 Digital Orbital Shaker

Weight Capacity: approx. 35 lbs. (16kg) at 75 rpm approx. 5 lbs. (2.3kg) at 500 rpm
Orbit: .75″ (1.9cm)
Speed Range: 25 to 500 rpm
Operating Temp: 4º C to 40º C
Voltage:120 volts AC, 50/60 hertz 230 volts AC, 50/60 hertz
Current: Less than 1 amp
Fuses:120v – 2 – 5 amp 5 x 20mm quick acting 230v – 2 – 5 amp 5 x 20mm quick acting
Power: 120 watts
Controls:On/Off switch LED display for Time/Speed, Up/Down Keypad for setpoint control Run/Stop keypad
Timer: Digital, 1 second to 9999 minutes (increased in 1 second increments)
Dimensions: 7¼”H x 10″W x 15″D (18.0cmH x 27.3cmW x 38.0cmD)
Ship weight:50 lbs. (23kg)

INTRODUCTION
The 120v and 230v units are supplied with a 3-prong power cord that should be plugged into a standard 3-prong grounded outlet. If the cord supplied does not meet your needs, please use an approved power cord that suits local codes and electrical supply.

OPERATINGINSTRUCTION

1. Please familiarize yourself with the features and operation completely before operating the unit.
2. Be sure the power switch is in the off position.
3. Plug the cord into a properly grounded three pronged outlet.
4. Your Orbital Shaker is ready for use.
5. Turn the Power on by depressing the left side of the rocker switch on the bottom left side of the control panel. LED displays for speed and timer will light.
6. Set speed by pressing the Up/Down arrows to the right of the speed display until you reach the desired speed. Adjust time using the Up/Down arrows to the right of the timer display. Press the run button. Timer LED will display time remaining.
7. To run in the un-timed mode, set the time to zero (0) using the Up/Down arrows to the right of the timer display. Press the run button and the unit will run until you press the stop button. Timer LED will display accumulated time.

OPERATION NOTES
Your Orbital Shaker automatically restarts after a power interruption. Built- in memory maintains time and speed settings during a power interruption.
The Orbital Shaker is designed to be balanced with the large platform attached (platform weight is 3 lbs). At the higher speeds, 200 rpm and above, the shaker should be run with this weight as a minimum, on a stable surface for maximum stability.

DS-500E Heavy-Duty Orbital Shaker

Weight Capacity: Approx. 50 lbs (22kg) at 200 rpm Approx. 10 lbs (4.5kg) at 500 rpm
Orbit: .75″ (1.9cm)
Speed Range: 25 to 500 rpm
Operating Temp: 4º C to 40º  C
Voltage:120 volts AC, 50/60 hertz 230 volts AC, 50/60 hertz
Current: Less than 1 amp
Fuses:120v – 2 – 5 amp 5 x 20mm quick acting 230v – 2 – 5 amp 5 x 20mm quick acting
Power: 120 watts
Controls: On/Off switch LED display for Time/Speed, up/down Keypad for setpoint control Run/Stop keypad
Timer: Digital, 1 second to 9999 minutes (increased in 1 second increments)
Dimensions: 10 3/4″ x 15″ x 7 1/4″ (27.3W x 38D x 18.8H cm)
Ship Weight:75 lbs (34kg)

INTRODUCTION
The 120v and 230v units are supplied with a 3-prong power cord that should be plugged into a standard 3-prong grounded outlet. If the cord supplied does not meet your needs, please use an approved power cord that suits local codes and electrical supply. The orbital shaker is equipped with anRS232 serial interface, which is used to monitor and/or control the shaker. Please contact your VWR International representative for more information.

OPERATING INSTRUCTIONS

1. Please familiarize yourself with the features and operation completely before operating the unit.
2. Be sure the power switch is in the off position.
3. Plug the cord into a properly grounded three pronged outlet.
4. Your Orbital Shaker is ready for use.
5. Turn the Power on by depressing the left side of the rocker switch on the bottom left side of the control panel. LED displays for speed and timer will light.
6. Set speed by pressing the Up/Down arrows to the right of the speed display until you reach the desired speed. Adjust time using the Up/Down arrows to the right of the timer display. Press the run button. Timer LED will display time remaining.
7. To run in the un-timed mode, set the time to zero (0) using the Up/Down arrows to the right of the timer display. Press the run button and the unit will run until you press the stop button. Timer LED will display accumulated time.

OPERATION NOTES:
Your Orbital Shaker automatically restarts after a power interruption. Built- in memory maintains time & speed settings during a power interruption.
The Orbital Shaker is designed to be balanced with the large platform attached. At the higher speeds, 200 rpm and above, the shaker should be run with this weight as a minimum, on stable surface, for maximum stability.

DS2-500-1
DS2-500-2
Large Heavy-DutyDigital Orbital Shaker

Weight Capacity:
DS2-500-1: 110 lbs (49kg) at 25 rpm 40 lbs (18kg) at 400 rpm
DS2-500-2: 110 lbs (49kg) at 25 rpm 40 lbs (18kg) at 200 rpm
Orbit: DS2-500-1: 1″ (25.4mm) DS2-500-2: 2″ (51.0mm)
Speed Range: DS2-500-1:25 to 500 rpm
DS2-500-2: 25 to 300 rpm
Operating Temp: 4º C to 40º C
Voltage: 120 volts AC, 50/60 hertz 230 volts AC, 50/60 hertz
Current: Less than 1 amp
Fuses: 120v – 2 – 5 amp 5 x 20mm quick acting 230v – 2 – 5 amp 5 x 20mm quick acting
Power: 120 watts
Controls: On/Off switch LED display for Time/Speed, Up/Down Keypad for setpoint control Run/Stop keypad
Timer: Digital, 1 second to 9999 minutes (increased in 1 second increments)
Dimensions: 25″ x 28″ x 8″ (63.5W x 71.1D x 20.3H cm)
Ship weight: 200 lbs (90kg)

INTRODUCTION
The 120v and 230v units are supplied with a 3-prong power cord that should be plugged into a standard 3-prong grounded outlet. If the cord supplied does not meet your needs, please use an approved power cord that suits local codes and electrical supply. The orbital shaker is equipped with anRS232 serial interface, which is used to monitor and/or control the shaker. Please contact your VWR International representative for more information.

OPERATINGINSTRUCTIONS

1. Please familiarize yourself with the features and operation completely before operating the unit.
2. Be sure the power switch is in the off position.
3. Plug the cord into a properly grounded three pronged outlet.
4. Your Orbital Shaker is ready for use.
5. Turn the Power on by depressing the left side of the rocker switch on the bottom left side of the control panel. LED displays for speed and timer will light.
6. Set speed by pressing the Up/Down arrows to the right of the speed display until you reach the desired speed. Adjust Time using the Up/Down arrows to the right of the timer display. Press the run button. Timer LED will display time remaining.
7. To run in the un-timed mode, set the time to zero (0) using the Up/Down arrows to the right of the timer display. Press the run button and the unit will run until you press the stop button. Timer LED will display accumulated time.

OPERATION NOTES:
A built-in program will shut power off to the motor if the table top is prevented from rotating, or the unit is overloaded.
Your Orbital Shaker automatically restarts after a power interruption. Built- in memory maintains time & speed settings during a power interruption.
This Orbital Shaker is optimally balanced with the 24″ x 24″ platform attached and 40 lbs of accessories. At higher speeds, the shaker should be run with this weight as a minimum, on stable surface for maximum stability.

DS2-500E-1
DS2-500E-2
Large High Performance Digital Orbital Shaker

Weight capacity:
DS2-500E-1: 160 lbs (72kg) at 25 rpm 60 lbs ( 27kg) at 250 rpm
DS2-500E-2: 160 lbs (29kg) at 25 rpm 60 lbs (27kg) at 175 rpm 60 lbs (27kg) at 175 rpm
Orbit: DS2-500E-1:1″ (25.4mm) DS2-500E-2:2″ (51.0mm)
Speed Range: DS2-500E-1:25 to 500 rpm DS2-500E-2:25 to 300 rpm
Operating Temp: 4º C to 40º C
Voltage: 120 volts AC, 50/60 hertz
Current: Less than 1 amp
Fuses: 120v – 2 – 5 amp 5 x 20mm quick acting 220v – 2 – 5 amp 5 x 20mm quick acting
Power: 120 watts
Controls: On/Off switch LED display for Time/Speed, Up/Down Keypad for setpoint control Run/Stop keypad
Timer: Digital, 1 second to 9999 minutes (increased in 1 second increments)
Dimensions: 25″ x 28″ x 8″ (63.5W x 71.1D x 20.3H cm)
Ship Weight: 230 lbs (104 kg)
INTRODUCTION
The 120v and 230v units are supplied with a 3-prong power cord that should be plugged into a standard 3-prong grounded outlet. If the cord supplied does not meet your needs, please use an approved power cord that suits local codes and electrical supply. The orbital shaker is equipped with anRS232 serial interface, which is used to monitor and/or control the shaker. Please contact your VWR International representative for more information.
OPERATINGINSTRUCTIONS

1. Please familiarize yourself with the features and operation completely before operating the unit.
2. Be sure the power switch is in the off position.
3. Plug the cord into a properly grounded three pronged outlet.
4. Your Orbital Shaker is ready for use.
5. Turn the power on by depressing the left side of the rocker switch on the bottom left side of the control panel. LED displays for speed and timer will light.
6. Set speed by pressing the Up/Down arrows to the right of the speed display until you reach the desired speed. Adjust time using the Up/Down arrows to the right of the timer display. Press the run button. Timer LED will display time remaining.
7. To run in the un-timed mode, set the time to zero (0) using the Up/Down arrows to the right of the timer display. Press the run button and the unit will run until you press the stop button. Timer LED will display accumulated time.

OPERATION NOTES:
A Built-in program will shut power off to the motor if the table top is prevented from rotating, or the unit is overloaded.
Your Orbital Shaker automatically restarts after a power interruption. Built- in memory maintains time & speed settings during a power interruption.
This Orbital Shaker is optimally balanced with the 24″ x 36″ platform and 60 lbs of accessories attached. At higher speeds, the shaker should be run with this weight as a minimum, on stable surface,for maximum stability.

ACCESSORIES

PLATFORMS

Small Platform
(13″ x  13″)| X-Large Platform
(24″ x 24″)
Large Platform
(18″ x 18″)| Jumbo Platform
(24″ x 36″)
Double Tier Braces
(for stacking 18″x18″ platform)| Universal Platform
(13″ x 14″)

Caution- Install platforms on shakers before adding flask clamps tube racks or other accessories. 2 people may be needed for installation of X-large and Jumbo platforms.
Caution- When using platform accessories, tighten mounting screws periodically. IF EXCESSIVE NOISE OCCURS WHILE RUNNING UNIT, stop immediately and check mounting screw tightness.

Installation for Small and Large Platforms
The black pad does not have to be removed. Loosen the four knobs on the shaker approximately 1/4″. Place platform on shaker by aligning the slots on the bottom (underside) of the platform to the knobs, slide the platform over the knobs on the shaker. When aligned, hand-tighten the four knobs. DONOT OVER- TIGHTEN.

Installation for X-Large and Jumbo Platforms
Remove black pad before mounting platforms on trays. Line up platform to installation holes on tray. Carefully place platform on tray. (hold platform with palms on outside
of tray). Tighten screws into mounting holes.

Double Tier Braces
Package Contents:
4 – Tier braces
21 – Hex head screws
32 – Hex head nuts
32 – Lock washers
Using 7/16″ socket wrench, hex head nuts, lock washers and hex head screws, attach brackets to each of the four corners of the first (bottom) platform by aligning mounting holes on bracket to mounting holes on platform. Hold second (top) platform in place and align the mounting holes on the bracket
already attached to first platform to the second platform.Tighten all screws. Follow instruction for installing large platforms on page 13.

UNIVERSALPLATFORMATTACHMENT

Installation for OS-500,DS-500,DS-500E
Loosen the four knobs on the shaker approximately 1/4″. Place platform on shaker by aligning the slots on the bottom of the platform to slide over
the knobs on the shaker. When aligned, hand-tighten the four knobs. DO NOT OVER-TIGHTEN (Mounting screws are not needed for this installation).

Installation for DS2-500,DS2-500E
Remove black mat from the shaker. There are four mounting holes in the middle of the tray, place the platform on the tray, align the mounting screws in the platform to the mounting holes in the tray, tighten with a #2 phillips head screwdriver. DONOTOVER-TIGHTEN
Installation of foam rollers
Insert knobs in the rail mounts. Insert rail mounts with knobs into support rods. Place rods with knobs and mounts added onto the platform rails. Adjust to the desired width and tighten knobs. Your platform is now ready to use.

TEST TUBE RACKS

Package Contents:
1 – Test Tube rack
2 – Mounting knobs
2 – Washers

Installation:
Align mounting hole on test tube rack to mounting holes on platform, place washer between test tube rack and mounting knob. Hand-tighten mounting
knobs. DONOT OVER-TIGHTEN.

FLASK CLAMPS

Description
10ml
25ml
50ml
125ml
250ml
500ml| Description
1 liter
2 liter
2.8 liter
4 liter
6 liter
---|---

MEDIA BOTTLE CLAMPS

Description .
500ml
1000ml
Package contents:

Clamp, installation screw(s), extension spring (10ml and 25ml flask clamps do not require an extension spring)
Installation- Line up the hole(s) in the clamp to the hole(s) in the platform you will be using, hand-tighten into place with a flathead screwdriver. Insert the flask/media bottle into clamp and wrap the supplied spring around the neck of the clamp to hold secure. 10ml – 500ml clamps are provided with 1 screw for installing on platform. 1 liter – 6 liter and media clamps are provided with 5 screws for installing on platform.

Capacity Chart

MANUFACTUREDBY:
HENRY TROEMNER LLC
201 Wolf Drive PO Box 87
Thorofare, NJ 08086-0087
Phone: 856-686-1600
Fax: 856-686-1601
www.troemner.com
email: troemner@troemner.com
580025-00

Artisan Technology Group is an independent supplier of quality pre-owned equipment
Gold-standard solutions
Extend the life of your critical industrial, commercial, and military systems with our superior service and support.
We buy equipment
Planning to upgrade your current equipment? Have surplus equipment taking up shelf space? We’ll give it a new home.
Learn more!
Visit us at artisantg.com for more info on price quotes, drivers, technical specifications, manuals, and documentation.
Artisan Scientific Corporation dba Artisan Technology Group is not an affiliate, representative, or authorized distributor for any manufacturer listed herein.

We’re here to make your life easier. How can we help you today?
217-352-9330 I sales@artisantg.com I artisantg.com

Artisan Technology Group – Quality Instrumentation … Guaranteed | (888) 88-SOURCE | www.artisantg.com

4-046-INS Rev

Documents / Resources

| VWR INTERNATIONAL DS-500 Orbital Shaker [pdf] Instruction Manual
DS-500 Orbital Shaker, DS-500, Orbital Shaker, Shaker
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>