LENRUE A10 Bluetooth Speaker User Manual
- June 7, 2024
- LENRUE
Table of Contents
Contact Email: oyfun.service@gmail.com
What’s included
The above pictures are just for reference only.
Attention
- Use original or certified cables
- Don’t expose to liquids
- Don’t disassemble
- Avoid dropping
- Avoid extreme temperatures
- Don’t listen to music for a long time in a high-volume environment.
At a Glance
1 | Poweron /off Multi-function button | 6 | SD card slot |
---|---|---|---|
2 | Volume down/ Previous track | 7 | Micro USB charging port |
3 | Play/ pause &Answer/end call | 8 | light |
4 | Volume up / Next track | 9 | Reset |
5 | USB | 10 | AUX in 3.5 Jack to jack |
Quick Start Guide
TWS Connect
-
Turn on the two speakers and enter the Wireless mode, double-click one of the ‘M’ keys to connect the two speakers.
-
After connecting A10 with a wireless device, you can play music to realize double surround sound.
Using Your Speaker
1. Turn on/off
Press and hold the Power onion button for 2 seconds, when LED ring around
buttons rapidly Rapedly blue speaker is in pairing, made Press Power on / Ott
bullpen again to turn on / ad the LED Ring Press and holl again to turn Off
speaker
2. Select mode
Press to (multi-function button) to select mode between Bluetooth mode /AuX
Mode/ SO Care mode
Inserting a card will automatically switch to sd card mode
A. Wireless mode
- Turn on the speaker.
- Turn on wireless smartphones or other devices.
- Find Wireless name in wail list and land for connection
Rapidly flashing blue | Pairing mode |
---|---|
Steady blue | Connected to a device |
**** Play / pause
Answer/end call Press Play/pause for answering a coming call, double press to end the call
Force disconnect Wireless Press and hold play/pause to disconnect Wireless, speaker enters to pairing mode
Volume up / down Press to volume up/down
Next track/Previous track Press and hold for next/previous track
**When turned on, the speaker will automatically connect to the last
connected device if available. If not, the speaker will enter pairing mode.
To pair a different device, press and hoild play/pause button for 3 seconds to
re-enter pairing mode. Then repeat the pairing steps.
Having connection problems?
Remove speaker from your device’s Bluetooth history, ensure it is less than 3
feet away then try pairing again.
B. AUX-In mode
Connect the speaker with provided 2 in 1 cable with Micro USB end, 3.5mm audio
jack plugging other deice. Press M(Multi-function button) to enter AUX mode.
When using AUX mode, control audio playback via the connected device.
C. SD card mode**
In SD card mode, control audio play track as same as Bluetooth mode
- Support a class 4 or above micro SD card, up to 32GB
- Support audio formats: MP3, WMA, WAV etc.
Charge your Speaker
Please charge your speaker when speaker gives tones.
Steady red | Charging |
---|---|
OFF | Fully Charged |
Using the included USB cable to charge your speaker and make sure it is fully charged before first use.
Specifications
Input | 5V/1A |
---|---|
Charging Time | 2-3hours |
Audio Output | 5Wx2 |
Battery Capacity | 1500mAh |
Play Time (variesby volume leveland content) | 10hours |
Size | 175x47x70mm |
Range | 33ft |
FCC Caution
NOTE : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the
following measures.
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference.
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>