kapture 1080P Full HD Dual Channel Dash Camera User Manual

kapture 1080P Full HD Dual Channel

 _ **Dash Camera User Manual**_

1.0 CAUTION

• Ensure you are using your Car Dash Cam within your countries’ road laws. Please make sure you are familiar with your local road legislation before use.
• Please set time and date before you use this device to record.
• The notifications given by the Car Dash Cam are suggestions only, please drive to the actual conditions
• The results of GPS positioning are only for reference. The Car Dash Cam will lose GPS positioning abilities when signal is blocked (e.g. driving through tunnels, enclosed car parks).
• GPS positioning accuracy may vary depending on weather and surroundings such as dense cities, tunnels, or forests. GPS satellite signals cannot pass through most solid materials. Tinted windows may also affect the GPS signal.
• The values displayed in this system, such as speed, position, and the distance warning, may be affected by the surrounding environment.
• The system is to be used only for non-commercial use, within the limits permitted by the relevant laws.
• Avoid using the Car Dash Cam near any devices that emit radio interference (e.g. Microwave Ovens).
• It is considered normal operation for the Car Dash Cam to get warm during use.

1.1 BATTERYWARNING

• Always charge the Car Dash Cam using the provided charger. Improper charging of the Car Dash Cam and may result in failure of the internal battery.
• Never dismantle the Car Dash Cam or expose the internal battery.
• Do not dispose of the Car Dash Cam in fire.
• Dispose of the Car Dash Com observing local regulations being mindful of the internal battery.
• Do not attempt to replace or expose the internal battery.

NOTES ON INSTALLATION

• It is advised that the Car Dash Cam is installed near the rear view mirror, at the top center of the windshield for optimal operation.
• Make sure that the lens is within the range of the windscreen wiper to ensure a clear view when it rains.
• Do not touch the lens with your fingers. Finger prints left on the lens will result in unclear videos or photos. If photos or videos are blurred, please clean the lens gently with a microfiber cloth.
• Do not install the device on a tinted window. Doing so may damage the tint film and restrict the Car Dash Cam’s GPS signal.
• Make sure that the installation position does not hinder or block the field of view or GPS signal.
• Only use the included cable to power the Car Dash Cam.
• The KPT-1022 is designed to be constantly connected to the included power supply, and is NOT designed to be used solely with the camera’s built in battery.

1.2 PRODUCT INFORMATION

For latest manual and product updates please visit our website at www.kapturecam.com.au or www.kapturecam.co.nz.

2.0 INTRODUCTION

Thank you for purchasing a Kapture Dash Cam. Please read through instructions before attempting to install or use this product.
This User guide is designed to assist with the day to day operation of the KPT-1022.
Before attempting to use or install your Kapture KPT-1022, please ensure you have read and understood all of the safety notes below.

• Do not expose your KPT-1022 to liquids, excessive dusty conditions or temperatures exceeding 60°C.
• Only use the included cables to power and charge the KPT-1022.
• Please do not attempt to adjust the KPT-1022 position or settings whilst you are operating your vehicle.
• Please clean the windshield thoroughly removing all dust and dirt particles before fixing the adhesive mount.
• Since the mount sticks onto the windshield using a 3M adhesive, please ensure that the position of the camera is best located to capture the maximum viewing area.
• We suggest you to power-on the dash camera and test the playback image on screen first prior to removing the 3M tape for installation.
• Only remove the 3M tape when you are satisfied with the dash camera placement and image position are delivering the best possible image and view of the road ahead.
• Ensure you are using your KPT-1022 within your countries’ road laws. Please make sure you are familiar with your local road legislation before use.

2.1 PACKAGE CONTENTS

2.2 PRODUCT OVERVIEW

1. Menu/Mode Button
2. Up Button
3. Lock Recording Button
4. Down Button
5. Rec/Ok Button
6. ON/OFF Power Button
7. Micro SD Card slot*
8. Mini USB Power socket
9. Reset
10. Microphone
11. Speaker
12. Lens
13. Slot for Mount
14. Cam/Rear Camera In
15. LCD Screen
16. Recording Indicator LED

3.0 BUTTON FUNCTIONS AND INDICATORS

Please press the OK button to stop recording before menu can be used.

4.0 GETTING STARTED

4.1 INSERTING A MICRO SD CARD

With the Car DVR turned off and the screen facing towards you insert your Micro SD Cord (not included) in the slot on the left side of the KPT-1022 with the text on the Micro SD cord facing to you. Push the memory cord in until a click is heard.

4.2 REMOVING A MICRO SD CARD

Ensure that the KPT-1022 is powered off, and with your thumbnail press in the Micro SD Card until a click is heard. The Micro SD Cord will eject from the KPT-1022 when released.

NOTE:

• Micro SD Card is not included.
• Do not remove or insert the memory card while the Car DVR is turned on as this may damage the memory card or corrupt the memory cords stored data.
• Please use a Closes 10 or higher rotted micro SD card with a minimum capacity of 32GB and a maximum capacity of128GB.
• Please format the Micro SD card before the initial use.
• When removing the memory card, be careful as the cards may eject quickly.

4.3 INSTALLING THE KPT-1022

1. OPTIONAL: Remove the protective layer from the Electrostatic film (Provided) end place it on your windscreen. This helps to easily remove the 3M adhesive from your windscreen with out any adhesive residue.
2. Remove the protective stickers from the Car DVR and the 3M mount.
3. Press the mount base firmly against the windscreen and hold for 30 seconds.
4. Insert the power cable adapter onto the dash camera power socket. Then insert the rear camera in the CAM port on DVR.

NOTE:

• It is advised that the KPT-1022 is installed in the center of the windscreen behind the rear view mirror.

4.4 INSTALLING THE REAR CAMERA

4.4.1 INSTALLATION GUIDE

Select a flat and centered location near the number plate lamp at the rear of the vehicle to mount camera.

Attach tape to the bracket of the camera to hold the camera in position while installing, and drill two small holes, one for the first screw, the second to run the reverse camera cable through.

1. Select a flat and centered location near the number plate lamp at the rear of the vehicle to mount camera.

2. Attach tope to the brocket of the camera to hold the camera in position while installing, and drill two small holes, one for the first screw, the second to run the reverse camera cable through.

3. Use a screw driver to fix the first screw, leaving the screw loose enough to adjust the camera.

4. Insert the camera wire through the intended drilled hole checking the installation position.

5. Mark the position suitable for the second screw and drill a small hole for it.

6. Fix the second screw and securely tighten both screws.

4.4.2 REAR CAMERA WIRING DIAGRAM

4.4.3 REAR CAMERA FEATURES

After successfully installing and connecting the rear camera into the main DVR, the rear camera will be displayed on the Dash Cam’s 2.4″ IPS Screen.
Both Cameras will instantaneously start recording offer DVR is powered ON.

Both Front and Rear Camera images will now be displayed on your Dash Camera’s 2.4″ Screen, you can switch between them by pressing the DOWN Key.

Display can switch between:

1. Full Front Camera view
2. Full Rear Camera view
3. Full Front with small window for Rear Camera
4. Full Rear Camera with small window for front

When your vehicle is in reverse gear, the display will change to the Rear Camera view with Reversing Grid Lines to assist the driver when reversing / parking.

5.0 CONNECTING TO POWER

Only use the included charger to power and charge the Car DVR.

1. Once the Car DVR is securely installed on your vehicle’s windscreen, plug the DC Power Plug into your vehicle’s cigarette lighter.
2. Run the power cable along your vehicle’s console and windscreen and plug the USB Micro plug into the Car DVR and the USB A end into the DC Power Plug.

NOTES:

• It is recommended that the Car DVR is installed behind your vehicle’s rear view mirror.
• Make sure that the camera view is not obstructed by any window tint or any other objects.
• The KPT-1022 is designed to be constantly powered by the included DC Power Plug. The internal battery is designed ta hold saved settings and power the camera when in Park Mode. The battery is NOT designed for primary use.

6.0 LED INDICATOR

• Flashing blue LED shows camera’s internal battery is getting charged and is recording.
• Continuous blue shows it is charging but not recording.

7.0 POWERING THE KPT-1022 ON/OFF

7.1 AUTO POWER ON/OFF

When the Car DVR is correctly installed and connected to your vehicle’s 12/24v power supply, the Car DVR will automatically power up and start recording when the vehicle accessories are activated.

7.2 MANUAL POWER ON

Hold the Power button on the lower right honed side of the camera until the Kapture start up screen appears.

7.3 MANUAL POWER OFF

Press the Power button on the lower right hand side of the car DVR. After powering down the device please wait for 10 seconds before turning the Cor DVR bock on.

7.4 RESET THE CAR DVR

If the Car DVR does not function normally, try restarting the car DVR. To restart the car DVR, using a small pin press and hold the Reset button on the bottom side of the camera.

8.0 INITIAL SETTINGS

Before using the Car DVR we recommend Formatting the Inserted Micro SD Card and setting the correct Time and Date.

8.1 FORMATTING THE INSERTED MICRO SD CARD

Formatting the Micro SD card will delete all information on the inserted Micro SD Card and prepare the card for use with the Car DVR.

1. Press the Menu Button to enter the Settings/Setup Menu.
2. Use the Up and Down Keys to navigate the Settings Menu and highlight the Format SD Card setting and press the OK to select.
3. Press Up and Down Keys to select confirm.
4. Press the OK button to start formatting.

Quick Format (Default), you can switch quick formatting to change to full formatting in the Setting Menu.

NOTES:

• Menus cannot be accessed while the camera is recording. Please stop the recording before attempting to access the menu.
• Formatting your Micro SD Card will delete all files from the card. Once these files have been deleted you will not be able to recover them.

8.2 SETTING THE TIME AND DATE

Setting the Time and Date allows you to stamp your footage with the time as a reference.

1. Press the Menu Button to enter the Settings/Setup Menu.
2. Press the UP end Down Key to select Date/Time.
3. Press the OK Key to enter into Date/Time setting.
4. Press the Up/Down to change the date time and press OK to move to next digit.
5. Press OK to confirm the Setting and return to previous menu.

9.0 REAL TIME ROAD ALERTS

Your Dash Camera comes with the added feature of providing real time road safety alerts. The alerts will be displayed on the LCD Screen showing your actual live speed, speed limit (if applicable) and distance to the alert. These alerts can be individually disabled from the settings menu.

9.1 SPEED CAMERA ALERT

Will alert you of Speed and Red light cameras at your designated distance. The alert will show the speed limit with you current speed and a count down of the distance.

9.2 BLACKSPOT ALERT

Blackspot alerts you before a high accident zone.

9.3 SCHOOL ZONE ALERT

School Zone alerts you before school zone.

9.4 RAILWAY CROSSING ALERT

Railway Crossing alert gives you the alert before the railway crossing.

NOTE:

• Distance of alerts to start can be selected from the Setting Menu. Distance can be set to 100M, 200M, 300M, 400M and S00M.
• Here Maps does not support School Zone & Accident Blackspot Alerts for New Zealand.

10.0 INTERFACE

10.1 VIDEO MOOE

1. Video Mode: Number 3 shows the loop recording duration.

2. Duration : 00:00:01 Loop Recording timer.

3. GPS : GPS Signal Indicator.

4. G-Sensor: The highlighted bar indicated the sensitivity of
   G-Sensor with 1 Bar indicates Low Sensitivity.

5. Park Mode: The highlighted bar indicates the sensitivity of
   Park mode with 1 Bar indicates Low Sensitivity.

6. WIFI : Displays WiFi connectivity

7. Microphone : Turns on or off the Microphone.

8. Micro SO Card: Indicates inserted SD Card.

9. Battery : Indicates battery level.

10. Speed : Displays current speed.

11. Date : (01/01/2019)

12. Time : (00:00:01)

11.0 PLAYBACK VIDEO

1. If the driving recorder is doing camera shooting, press OK key first to stop camera shooting.
2. Long press ( M) Menu key to switch to playback mode.
3. Short press ▲ or ▼ key to page up or down to select files.
4. Short press OK key to ploy selected video files; short press it again to pause.
5. Press( M) Menu key to delete a file.
6. Long press mode key to exit out of playback mode.

11.1 SETUP MENU

1. Press (OK) to stop Recording.
2. Press the (M) Menu button to enter into the Settings Menu.
3. Press the ▲ and ▼ Button to select the setting you wish to change.
4. Press (OK) Button on your selected option.
5. New Setting will be shown on the top left of the screen and also on the selected setting icon.

12.0 SOFTWARE PLAYBACK

Your DVR with inbuilt GPS will record the GPS coordinates and the speed of your travel on the recorded footage.

To ploy back the GPS footage, Please download the player from www.kapturecam.com.au/product/KPT-1022 and run it on your windows player.

To view images from Dosh Camaro, you will need to remove the Micro SD Cord and transfer the files to you computer using a Micro SD Cord Slot or compatible USB adapter. If need check the GPS information, the professional player must be installed firstly.

Once files have been transferred to your computer, please select the folder and select the file you wish to view or playback.

13.0 INSTALLING APP ON SMART PHONE

Please download the KPT-1022 App from the Google Play Store or Apple App Store depending on your mobile device. After successfully downloading and installing the app on your mobile. Search for KPT-1022-XXXX (the last 4 digit are unique to each dash camera) WIFI connection and connect it on your mobile device by entering password “12345678”. Open the app and sync it with the DVR, this allow you to access your the app.

14.0 WARRANTY TERMS & CONDITIONS

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. This warranty is provided in addition to your rights under the Australian Consumer Law. Directed Electronics warrants that this product is free from defects in material and workmanship for a period of 12 months from the date of purchase or for the period stated on the packaging. This warranty is only valid where you have used the product in accordance with any recommendations or instructions provided by Directed Electronics.
This warranty excludes defects resulting from alterations of the product, accident, misuse, abuse or neglect. In order to claim the warranty, you must return the product to the retailer from which it was purchased or if that retailer is part of a National network, a store within that chain, along with satisfactory proof of purchase. The retailer will then return the goods to Directed Electronics. Directed Electronics will repair, replace or refurbish the product at its discretion. The retailer will contact you when the product is ready for collection. All costs involved in claiming this warranty, including the cost of the retailer sending the product to Directed Electronics, will be borne by you.

Directed Electronics
Address: 44 Translink Drive, Keilor Park Victoria 3042
Ph: +61 03 8331 4800 | Email: service@kapturecam.com.au
27

15.0 NOTES

_____

YOUR EYEWITNESS ON THE ROAD™

All Images, information and Content are Copyright 0 2019
Directed Electronics Australia Pty Ltd. All Rights Resealed.
www.kopturecom.com.au | www.kopturecom.co.nz

****www.directed.com.au
www.directed.co.nz

References

• Kapture

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>