EAZYZAP Fly Killer Instruction Manual

June 7, 2024
EAZYZAP

EAZYZAP logo

Fly Killer
Instruction manual

EAZYZAP Fly Killer -

Model :Y724 / Y725 / Y726

Safety Tips

  • A service agent/qualified technician should carry out installation and any repairs required. Do not remove components on this product.

  • Consult Local and National Standards to comply with the following: – Health and Safety at Work Legislation – BS EN Codes of Practice – Fire Precautions – IEE Wiring Regulations – Building Regulations

  • Always switch off and disconnect the power supply to the appliance before cleaning.

  • Install the appliance out of the reach of children.

  • Never insert hands or other objects into the appliance while it is connected to the power supply.

  • Install the Fly Killer at least 1 meter away from food preparation areas.

  • Never use near flammable objects.

  • For  INDOOR use only.

  • Keep all packaging away from children. Dispose of the packaging in accordance with the regulations of local authorities.

  •  If the power cord is damaged, it must be replaced by an EAZYZAP agent or a recommended qualified technician in order to avoid a hazard.

  • EAZYZAP recommends that this appliance should be periodically tested (at least annually) by a Competent Person. Testing should  include, but not be limited to: Visual Inspection, Polarity Test, Earth Continuity,
    Insulation Continuity and Functional Testing.

  • Danger – High voltage!

  • The appliance emits UV radiation. Do not stare at the light

  • The appliance is not to be used in locations where flammable vapor or explosive dust is likely to exist

  • Do not use in barns, stables, and similar locations.

Product Description

Y724 – 2x8W Fly Killer
Y725 – 2x15W Fly Killer
Y726 – 2x18W Fly Killer

Introduction

Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your EAZYZAP product.
Pack Contents
The following is included:
• Fly Killer
• Instruction manual
• Hanging chain
EAZYZAP prides itself on quality and service,  ensuring that at the time of packaging the contents are supplied fully functional and free of damage.
Should you find any damage as a result of transit, please contact your EAZYZAP dealer immediately.

Installation

Note: Ensure the mounting substrate and the fixings used can support the weight of the appliance. If in doubt seek professional advice or assistance.
1. Remove all packaging and protective film from the Fly Killer.
2. For best results, locate the Fly Killer in the darkest part of the room, but at least 1 meter away from food preparation areas.
Note: Close proximity to other light sources such as skylights and windows will reduce the effectiveness of the Fly Killer.
3. Connect the appliance to mains power.

Operation

WARNING: Under no circumstances should hands be placed anywhere near the high voltage grid when the appliance is operational.
The fly killer works by luring insects onto an electrified metal grid using ultra-violet light. It uses no chemicals and is pollution-free. To use the Fly Killer:
1. Press the switch to the ON (I) position. Ensure it is set to OFF (O) before plugging into mains.
2. The light will come on and the grid will become electrically charged.

Cleaning, Care &Maintenance

**Always switch off the power and disconnect the appliance from the power supply before cleaning.
• Clean the collection tray regularly with warm soapy water.
• DO NOT immerse the appliance in water. Wipe the safety guard and external casing with a damp cloth.
• Change the bulbs every 9 months.
Changing the Bulb
WARNING: Always turn Off the appliance and disconnect from the power supply before changing the bulb.**

  1.  Remove the collection tray.

  2. Lay the appliance face down.

  3. Unscrew the two screws holding the safety guard at the rear of the Fly Killer [Fig. 1].
    EAZYZAP Fly Killer -Remove the collection tray

  4. Lift up the guard rail [Fig. 2].
    EAZYZAP Fly Killer - Fig. 2

  5. Holding the ends of the bulb, twist it ‘forwards’ in its socket until it clicks [Fig. 3].
    EAZYZAP Fly Killer - Fig. 3

  6. Slide the bulb up out of its sockets [Fig. 4].
    EAZYZAP Fly Killer - Fig. 4

  7. Replace with a new bulb.

  8. Twist the new bulb ‘backward’ to lock it back in place.

  9. Replace the guard rail and the two screws.

Troubleshooting

Fault Probable Cause Solution
The appliance is not working The unit is not switched on Check the unit is

plugged in correctly and switched on
Plug and lead are damaged| Call EAZYZAP agent or qualified Technician
Fuse in the plug has blown| Replace the plug fuse
Power supply| Check power supply
Internal wiring fault| Call EAZYZAP agent or qualified technician
Tube has expired| Refer to the ‘Changing the Bulb’ section
The tube is faulty or has not been fitted correctly

Technical Specifications

Model| Voltage| Power| Dimensions
hxwxd(mm)| Weight
---|---|---|---|---
Y724| 220-240V 50Hz| 23W| 272 x 349 x 86| 2.36kg
Y725| 220-240V 50Hz| 39W| 320 x 498 x 86| 3.25kg
Y726| 220-240V 50Hz| 43W| 320 x 650 x 86| 3.87kg

Electrical Wiring

This appliance is supplied with a 3 pin BS1363 plug and lead.
The plug is to be connected to a suitable mains socket.
This appliance is wired as follows:

  • Live wire (colored brown) to the terminal marked L
  • Neutral wire (colored blue) to the terminal marked N
  • Earth wire (colored green/yellow) to terminal marked E

This appliance must be earthed.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency, disconnection is required they must be readily accessible.

Compliance

The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.
EAZYZAP parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities. EAZYZAP products have been approved to carry the following symbol:

All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written permission of EAZYZAP.
Every effort is made to ensure all details are correct at the time of going to press, however, EAZYZAP reserve the right to
change specifications without notice.

DECLARATION OF CONFORMITY

Conformiteitsverklaring

Equipment Type : Flykiller – 2x8watt

Flykiller – 2x15watt
Flykiller – 2x18watt

Model: Y724
Y725
Y726

Application of Council Directives(s):
Low Voltage Directive (LVD) 2014/35/EC
EN 60335-1:2012 +A11:2014
EN 60335-2-59:2003 +A1:2006 +A2:2009
EN 62233:2008
Electro-Magnetic Compatibility (EMC) Directive
2014/30/EU
EN 55014-1:2006 +A1:2009 +A2:2011
EN 55014-2:2015
EN 61000-3-3:2013
EN 61000-3-2:2014
Restriction of Hazardous Substances Directive
(RoHS) 2015/863 amending Annex II to Directive
2011/65/EU

Producer Name: Eazyzap

Producer Address: Fourth Way, Avonmouth,Bristol, BS11 8TBUnited Kingdom
42 North Point Business Park New Mallow Road Cork Ireland

I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s) and Standard(s).

Date: 7 August 2019
Signature:EAZYZAP Fly Killer - signATURE
Full Name:Ashley Hooper
Position:Technical & Quality Manager

+44 (0)845 146 2887

Documents / Resources

| EAZYZAP Fly Killer [pdf] Instruction Manual
Fly Killer, Y724, Y725, Y726
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals