DELL Vostro 3470 Small Desktop Computer User Guide
- June 7, 2024
- Dell
Table of Contents
Vostro 3470 Small Desktop Computer
Dell Vostro 3470
Setup and specification guide
Regulatory Model: D13S Regulatory Type: D13S003 September 2021 Rev. A03
Contents
Chapter 1: Set up your computer……………………………………………………………………………………… 5
Chapter 2: Chassis overview…………………………………………………………………………………………… 8 System front
view…………………………………………………………………………………………………………………………………………… 8 System back
view…………………………………………………………………………………………………………………………………………….9
Chapter 3: Technical specifications………………………………………………………………………………… 10 Physical
specifications…………………………………………………………………………………………………………………………………… 10 System
information……………………………………………………………………………………………………………………………………….. 10 Processor
specifications………………………………………………………………………………………………………………………………… 11 Operating
system specifications……………………………………………………………………………………………………………………. 11 Memory
specifications…………………………………………………………………………………………………………………………………….11 Port and
connector specifications………………………………………………………………………………………………………………… 12
Communication specifications………………………………………………………………………………………………………………………. 13
Video specifications………………………………………………………………………………………………………………………………………..13
Audio specifications………………………………………………………………………………………………………………………………………..14
Storage specifications…………………………………………………………………………………………………………………………………….14
Storage combinations……………………………………………………………………………………………………………………………………. 14
Power supply specifications………………………………………………………………………………………………………………………….. 14
Security hardware…………………………………………………………………………………………………………………………………………..15
Regulatory and Environmental Compliance…………………………………………………………………………………………………..
15
Chapter 4: System setup………………………………………………………………………………………………. 16 Accessing
System Setup………………………………………………………………………………………………………………………………..16 Navigation
Keys………………………………………………………………………………………………………………………………………………16 System setup
options……………………………………………………………………………………………………………………………………..17 General screen
options…………………………………………………………………………………………………………………………….. 17 System
Configuration screen options……………………………………………………………………………………………………… 17 Video
screen options………………………………………………………………………………………………………………………………… 18 Security
screen options……………………………………………………………………………………………………………………………. 19 Secure Boot
screen options……………………………………………………………………………………………………………………..20 Intel Software
Guard Extensions screen options…………………………………………………………………………………… 20 Performance
screen options…………………………………………………………………………………………………………………….20 Power Management
screen options………………………………………………………………………………………………………… 21 POST Behavior screen
options……………………………………………………………………………………………………………….. 22 Virtualization support
screen options……………………………………………………………………………………………………… 22 Wireless screen
options…………………………………………………………………………………………………………………………… 22 Advanced
configuration options……………………………………………………………………………………………………………… 23 Maintenance
screen options…………………………………………………………………………………………………………………….23 System Log
screen options………………………………………………………………………………………………………………………23 SupportAssist
System Resolution…………………………………………………………………………………………………………….23 Updating the
BIOS in Windows …………………………………………………………………………………………………………………… 23 System and
setup password………………………………………………………………………………………………………………………….24 Assigning a
system setup password……………………………………………………………………………………………………….. 24
2
Contents
Deleting or changing an existing system setup
password………………………………………………………………………25
Chapter 5: Software……………………………………………………………………………………………………..26 Supported
operating systems………………………………………………………………………………………………………………………. 26 Downloading
Windows drivers……………………………………………………………………………………………………………………… 26 Intel chipset
drivers…………………………………………………………………………………………………………………………………. 26 Serial IO
driver………………………………………………………………………………………………………………………………………….. 27 USB
drivers………………………………………………………………………………………………………………………………………………. 28 Network
drivers……………………………………………………………………………………………………………………………………….. 28 Realtek
Audio…………………………………………………………………………………………………………………………………………….28 Serial ATA
drivers…………………………………………………………………………………………………………………………………….. 29
Chapter 6: Getting help…………………………………………………………………………………………………30 Contacting
Dell……………………………………………………………………………………………………………………………………………… 30
Contents
3
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of
your product. CAUTION: A CAUTION indicates either potential damage to hardware
or loss of data and tells you how to avoid the problem. WARNING: A WARNING
indicates a potential for property damage, personal injury, or death.
© 2019-2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and
other trademarks are trademarks of Dell Inc. or its subsidiaries. Other
trademarks may be trademarks of their respective owners.
1. Connect the keyboard and mouse.
1
Set up your computer
2. Connect to your network using a cable, or connect to a wireless network.
3. Connect the display.
Set up your computer
5
NOTE: If you ordered your computer with a discrete graphics card, the HDMI and
the display ports on the back panel of your computer are covered. Connect the
display to the discrete graphics card. 4. Connect the power cable.
5. Press the power button.
6
Set up your computer
6. Follow the instructions on the screen to finish Windows setup: a. Connect
to a network.
b. Sign-in to your Microsoft account or create a new account.
7. Locate Dell apps. Table 1. Locate Dell apps Register your computer Dell
Help & Support
SupportAssist — Check and update your computer
Set up your computer
7
Topics:
· System front view · System back view
System front view
2
Chassis overview
1. Power button/power status LED 3. Memory card reader 5. USB 3.1 Gen 1 ports (2)
2. Hard drive activity light 4. Universal audio/microphone connector 6. Optical drive
8
Chassis overview
System back view
1. Line-in port 3. Microphone port 5. HDMI port 7. Service tag 9. Power connector port 11. Kensington security slot 13. Padlock ring
2. Line-out port 4. VGA port 6. USB 2.0 ports (4) 8. Expansion card slots 10. Power diagnostics light 12. Network port
Chassis overview
9
3
Technical specifications
NOTE: Offerings may vary by region. The following specifications are only
those required by law to ship with your computer. For more information about
the configuration of your computer, go to Help and Support in your Windows
operating system and select the option to view information about your
computer.
Topics:
· Physical specifications · System information · Processor specifications ·
Operating system specifications · Memory specifications · Port and connector
specifications · Communication specifications · Video specifications · Audio
specifications · Storage specifications · Storage combinations · Power supply
specifications · Security hardware · Regulatory and Environmental Compliance
Physical specifications
Table 2. Physical specifications Feature Height Width Depth Weight
Specifications 11.4 inch (290 mm) 3.6 inch (92.6 mm) 11.5 inch (293 mm) 19.7 lb (4.8 kg)
System information
Table 3. System information Feature Chipset DRAM bus width FLASH EPROM PCIe
bus External bus frequency
Specifications Intel H370 64-bit 256Mbit 100 Mhz DMI 3.0-8GT/s
10
Technical specifications
Processor specifications
NOTE: Processor numbers are not a measure of performance. Processor availability is subject to change and may vary by region/country.
Table 4. Processor specifications
Type
UMA Graphics
Intel 8th Generation Celeron processor G4900 (2M Cache, 2 Intel UHD Graphics 610 with shared graphics memory cores, 54 W, up to 3.1 GHz)
Intel 8th Generation Pentium Gold processor G5400 (4M Cache, 2 cores, 58 W, up to 3.7 GHz)
Intel UHD Graphics 610 with shared graphics memory
Intel 8th Generation Core i3-8100 processor (6 MB Cache, 4 Intel UHD Graphics 630 with shared graphics memory cores, 65 W, up to 3.6 GHz)
Intel 8th Generation Core i5-8400 processor (9 MB Cache, 6 Intel UHD Graphics 630 with shared graphics memory cores, 65 W, up to 4.0 GHz)
Intel 8th Generation Core i7-8700 processor (12 MB Cache, 6 Intel UHD Graphics 630 with shared graphics memory cores, 65 W, up to 4.6 GHz),
Intel Celeron 9th Generation Celeron G4930 (2M Cache, 2 cores, 54 W, up to 3.2 GHz)
Intel UHD Graphics 610 with shared graphics memory
Intel 9th Generation Pentium Gold G5420 (4M Cache, 2 cores, Intel UHD Graphics 610 with shared graphics memory 54 W, up to 3.8 GHz)
Intel 9th Generation Core i3-9100 (6 MB Cache, 4 cores, 65 W, up to 4.2 GHz)
Intel UHD Graphics 630 with shared graphics memory
Intel 9th Generation Core i5-9400 (9 MB Cache, 6 cores, 65 Intel UHD Graphics 630 with shared graphics memory W, up to 4.1 GHz)
Intel 9th Generation Core i7-9700 (12 MB Cache, 8 cores, 65 Intel UHD Graphics 630 with shared graphics memory W, up to 4.7 GHz)
Operating system specifications
Table 5. Operating system specifications Feature Operating systems supported
Specifications
Windows 10 64-bit Windows 10 64-bit Professional Windows 10 64-bit National
Academic (STF) Ubuntu 16.04 LTS (64-bit)
Memory specifications
Table 6. Memory specifications Feature Minimum memory configuration
Specifications 4 GB
Technical specifications
11
Table 6. Memory specifications (continued) Feature Maximum memory
configuration Number of slots Maximum memory supported per slot Memory options
Type Speed
Specifications
32 GB
2 UDIMM
16 GB
4 GB DDR4 2400 MHz (4Gx1) 8 GB DDR4 2400 MHz (8Gx1) 8 GB DDR4 2400 MHz (4Gx2)
12 GB DDR4 2400 MHz (8Gx1 + 4Gx1) 16 GB DDR4 2400 MHz (8Gx2) 16 GB DDR4 2400
MHz (16Gx1) 24 GB DDR4 2400 MHz (16Gx1 + 8Gx1) 32 GB DDR4 2400 MHz (16Gx2) 4
GB DDR4 2666 MHz (4Gx1) 8 GB DDR4 2666 MHz (8Gx1) 8 GB DDR4 2666 MHz (4Gx2) 12
GB DDR4 2666 MHz (8Gx1 + 4Gx1) 16 GB DDR4 2666 MHz (8Gx2) 16 GB DDR4 2666 MHz
(16Gx1) 24 GB DDR4 2666 MHz (16Gx1 + 8Gx1) 32 GB DDR4 2666 MHz (16Gx2)
NOTE: The memory modules are customer replaceable units (CRU), and it can be
upgraded.
NOTE: Memory configuration of 2400 MHz pair with PDC,
CDC, core i3 CPU Memory configuration of 2666 MHz pair with core i5,
i7 CPU
DDR4 SDRAM Non-ECC memory
2666 MHz on Core i5, i7 processor 2400 MHz on Celeron, Pentium, and i3
processor
Port and connector specifications
Table 7. Ports and connectors Feature USB Security Audio
Video
Specifications
Two USB 3.1 Gen 1 ports Four USB 2.0 ports
Kensington lock slot Padlock ring
Universal audio jack Microphone port Line-in port Line-out port
HDMI 1.4 (UMA) VGA port
12
Technical specifications
Table 7. Ports and connectors (continued) Feature Network adapter Secure Digital card
Specifications One RJ-45 connector SD card slot
Communication specifications
Table 8. Communication specifications Feature Network adapter
Wireless
Specifications
Realtek RTL8111H Gigabit Ethernet controller 10/100/1000 Mb/s Ethernet (RJ-45
)
Intel 9462 1×1 ac + BT5 (band – 2.4 Ghz, 5 Ghz; 802.11ac + Bluetooth 5.0, 1X1)
Intel 9560 2×2 ac + BT5 (band – 2.4Ghz, 5Ghz; 802.11ac + Bluetooth 5.0, 2×2)
DW 1707 + BT4.0 2.4 GHZ (band – 2.4 Ghz; 802.11bgn + Bluetooth 4.0, 1×1) via
M.2
Video specifications
Table 9. Video
Controller
Type
Intel UHD
UMA
Graphics 630
Intel UHD Graphics 610
UMA
NVIDIA GeForce GT 710
Discrete
CPU
Graphics
Capacity
Dependency memory type
External display Maximum
support
resolution
Intel Core i3 8100 / Intel Core i3 – 9100
Intel Core i5 8400 / Intel Core i5 – 9400
Intel Core i7 8700 / Intel Core i7 – 9700
Integrated
Shared system VGA
memory
HDMI 1.4
VGA: 2048×1536@60 Hz
HDMI : 1920×1080@ 60Hz
Intel Pentium Gold G5400 / Intel Pentium Gold G5420
Celeron processor G4900 / Intel Pentium Gold G4930
Integrated
N/A
DDR3
Shared system VGA
memory
HDMI 1.4
VGA: 2048×1536@60 Hz
HDMI : 1920×1080@ 60Hz
2 GB
DL-DVI HDMI VGA (FH only)
Dual Link DVI = 2560×1600
HDMI = 1920×1200 (PC Mode), 1920×1080 (TV mode, 1080p)
Technical specifications
13
Table 9. Video (continued)
Controller
Type
CPU Dependency
Graphics
Capacity
memory type
External display Maximum
support
resolution
VGA (optional) = 2048×1536
Audio specifications
Table 10. Audio specifications Feature Controller Type Interface
NOTE: No internal speakers
Specifications
Waves MaxxAudio Pro
Four-channel high-definition audio
Line-in, line-out, and microphone ports supporting 5.1 surround sound
High-quality speakers Stereo headset/mic combo
Storage specifications
Table 11. Storage specifications
Primary/Boot drive
Secondary drive
Solid-State Drive (SSD) Hard drive (HDD)
M.2 SATA 2280 2.5 inch and 3.5 inch
Interface SATA AHCI, Up to 6 Gbps SATA AHCI, Up to 6 Gbps
Capacity
Up to 512 GB Up to 2 TB at 5400 RPM and 7200 RPM
Storage combinations
Table 12. Storage combinations Primary/Boot drive M.2 Drive + SATA
Secondary drive M.2 128GB Solid State Drive+ 1TB 7200 rpm Hard Drive
Power supply specifications
Table 13. Power supply Feature Input Voltage Wattage
Specifications
100-240VAC, 200-240VAC, 5060 Hz
200 W APFC High voltage 200 W APFC 100V-240V Full range 200 W EPA Bronze
14
Technical specifications
Security hardware
Table 14. Security hardware Feature Security HW
Specifications
Data wipe via BIOS (Secure Erase) Support of Computrace BIOS agent supports
both
Computrace and Proactive Systems Management Discrete TPM 2.0 (optional) BIOS
disable TPM (China Only)
Regulatory and Environmental Compliance
Table 15. Regulatory and Environmental Compliance
Feature
Specifications
Regulatory and Environmental Compliance
Energy Star 7.0 (available in selected configurations only) FCC, UL mark EPEAT
Registered (for selected configurations only).
For specific country participation and rating, please visit www.epeat.net
CCC/CECP (China only) ESPL/ 1 Million Hr MTBF (China only, Post-RTS) INMETRO
(Brazil only)
Temperature range
Operating :10°C to 35°C (50°F to 95°F) Storage: -40°C to 65°C (-40°F to 149°F
Relative humidity
Operating : 20% to 80% (*Max dew point temperature = 26°C) (non-condensing)
Storage: 5% to 95% (+Max dew point temperature = 33°C) (non-condensing)
Airborne contaminant level
G1 as defined by ISA-S71.04-1985
Vibration
Vibration (maximum)*: operating=0.26 GRMS; Storage=1.37 GRMS
Shock
Shock (maximum): operating=40 G; Storage=105 G
Technical specifications
15
4
System setup
System setup enables you to manage your desktop hardware and specify BIOS
level options. From the System setup, you can: Change the NVRAM settings after
you add or remove hardware View the system hardware configuration Enable or
disable integrated devices Set performance and power management thresholds
Manage your computer security
Topics:
· Accessing System Setup · Navigation Keys · System setup options · Updating
the BIOS in Windows · System and setup password
Accessing System Setup
1. Turn on (or restart) your computer. 2. After the white Dell logo appears,
press F2 immediately.
The System Setup page is displayed. NOTE: If you wait too long and the
operating system logo appears, wait until you see the desktop. Then, shut down
or restart your computer and try again.
NOTE: After the Dell logo appears, you can also press F12 and then select BIOS
setup.
Navigation Keys
The following table displays the system setup navigation keys. NOTE: For most of the system setup options, changes that you make are recorded but do not take effect until you re-start the system.
Table 16. Navigation Keys
Keys
Navigation
Up arrow
Moves to the previous field.
Down arrow
Moves to the next field.
Allows you to select a value in the selected field (if applicable) or follow the link in the field.
Spacebar
Expands or collapses a drop-down list, if applicable.
Moves to the next focus area. NOTE: For the standard graphics browser only.
Moves to the previous page till you view the main screen. Pressing
Displays the System Setup help file.
16
System setup
System setup options
NOTE: Depending on the computer and its installed devices, the items listed in
this section may or may not appear.
General screen options
This section lists the primary hardware features of your computer.
Option
System Information
Boot Sequence
Description
System Information: Displays BIOS Version, Service Tag, Asset Tag, Ownership
Tag, Ownership Date, Manufacture Date, and the Express Service Code.
Memory Information: Displays Memory Installed, Memory Available, Memory Speed,
Memory Channels Mode, Memory Technology, DIMM 1 Size, DIMM 2Size.
Processor Information: Displays Processor Type, Core Count, Processor ID,
Current Clock Speed, Minimum Clock Speed, Maximum Clock Speed, Processor L2
Cache, Processor L3 Cache, HT Capable, and 64-Bit technology.
Device Information: Displays Primary Hard Drive, SATA-0, SATA-1, SATA-2,
SATA-3, LOM MAC Address, Video Controller, Audio Controller, WiFi Device,
M.2PCIe SSD-0, Dock eSATA Device, Video BIOS Version, Video Memory, Panel
Type, Native Resolution, WiGig Device, Cellular Device, Bluetooth Device.
Boot Sequence
Allows you to change the order in which the computer attempts to find an
operating system. The options are: Windows Boot Manager PEBOOT
By default, all the options are checked. You can also deselect any option or
change the boot order.
Boot List Options Allows you to change the boot list option: Legacy UEFI (default)
Advanced Boot Options
UEFI Boot Path Security
Date/Time
This option allows you the legacy option ROMs to load. By default, the Enable
Legacy Option ROMs is enabled This option allows you the legacy option ROMs to
load. By default, the Enable Attemot Legacy Boot
is disabled. .
This options control whether or not the system will prompt the user to enter
the Admin password (if set) when booting a UEFI boot path from the F12 Boot
Menu Always Except Internal HDD (default) Always Never
Allows you to change the date and time.
System Configuration screen options
Option
Integrated NIC
SATA Operation
Description
Allows you to configure the integrated network controller. The options are:
Disabled Enabled Enabled w/PXE: This option is enabled by default.
Allows you to configure the internal SATA hard-drive controller. The options
are: Disabled
System setup
17
Option
Drives
SMART Reporting USB Configuration
Front USB Configuration
Rear USB Configuration
Audio Miscellaneous Devices
Description
AHCI (default)
Allows you to configure the SATA drives on board. All drives are enabled by
default. The options are: SATA-0 SATA-1 SATA-2 SATA-3
This field controls whether hard drive errors for integrated drives are
reported during system startup. This technology is part of the SMART (Self-
Monitoring Analysis and Reporting Technology) specification. This option is
disabled by default. Enable SMART Reporting
This field configures the integrated USB controller. If Boot Support is
enabled, the system is allowed to boot any type of USB Mass Storage Devices
(HDD, memory key, floppy).
If USB port is enabled, device attached to this port is enabled and available
for OS.
If USB port is disabled, the OS cannot see any device attached to this port.
Enable USB Boot Support (default) Enable Front USB Ports(default) Enable Rear
USB Ports (default)
NOTE: USB keyboard and mouse always work in the BIOS setup irrespective of
these settings.
This field enables or disables the front USB configuration Front Port 1
(Bottom Right) (default) Front Port 2 (Bottom Left) (default)
- denotes a USB 3.0-capable port
This field enables or disables the front USB configuration Rear Port 1 Rear Port 2 Rear Port 3 (w/RJ-45) Rear Port 4 (w/RJ-45) - denotes a USB 3.0-capable port
This field enables or disables the integrated audio controller. By default, the Enable Audio option is selected.
Allows you to enable or disable the following devices: Enabled Secure Digital (SD) Card (default) Secure Digital (SD) Card Boot Secure Digital (SD) Card Read-Only Mode
Video screen options
Option
Primary Display
Description
This option determines which video controller becomes the primary display when
multiple controllers are available in the system Auto: This option is enabled
by default. Intel HD Graphics
18
System setup
Security screen options
Option
Description
Admin Password
Allows you to set, change, or delete the administrator (admin) password. NOTE: You must set the admin password before you set the system or hard drive password. Deleting the admin password automatically deletes the system password and the hard drive password.
NOTE: Successful password changes take effect immediately.
Default setting: Not set
System Password
Allows you to set, change, or delete the system password. NOTE: Successful password changes take effect immediately.
Default setting: Not set
Internal HDD-0 Password
Allows you to set, change, or delete the password on the system’s internal hard-disk drive. NOTE: Successful password changes take effect immediately.
Default Setting: Not set
Internal HDD-1 Password
Allows you to set, change, or delete the password on the system’s internal hard-disk drive. NOTE: Successful password changes take effect immediately.
Default Setting: Not set
Password Change
Allows you to enable the disable permission to the System and Hard Drive
passwords when the admin password is set.
Default setting: Allow Non-Admin Password Changes is selected.
UEFI Capsule
This option controls whether the system allows the BIOS updates through UEFI capsule update packages.
Firmware Update This option is enabled by default.
Non-Admin Setup Allows you to determine whether changes to the setup options are allowed when an Administrator
Changes
Password is set. If disabled the setup options are locked by the admin password.
TPM 2.0 Security Allows you to enable the Trusted Platform Module (TPM) during
POST. The options are:
TPM On (enabled by default) Clear PPI Bypass for Enabled Commands PPI Bypass
for Disabled Commands PPI Bypass for Clear Command Attestation Enable (enabled
by default) Key Storage Enable (enabled by default) SHA-256 (enabled by
default) Disabled Enabled (enabled by default)
NOTE: To upgrade or downgrade TPM1.2/2.0, download the TPM wrapper tool (software).
Computrace
Allows you to activate or disable the optional Computrace software The options
are: Deactivate Disable Activate
NOTE: The Activate and Disable options will permanently activate or disable
the feature and no
further changes are allowed
Default setting: Deactivate
Master Password The option Enable Master Password Lockout is not selected by default. Lockout
System setup
19
Option
SIMM Security Mitigation
Description
Allows you to enable or disable the additional UEFI SIMM Security Mitigation
protections. Default Setting: SIMM Security Mitigation is not selected.
Secure Boot screen options
Option
Secure Boot Enable
Secure Boot Mode
Expert Key Management
Description
This option enables or disables the Secure Boot feature.
Default setting: Not selected
Deployed Mode (default) Audit Mode
Allows you to manipulate the security key databases only if the system is in
Custom Mode. The Enable Custom Mode option is disabled by default. The options
are: PK (default) KEK db dbx If you enable the Custom Mode, the relevant
options for PK, KEK, db, and dbx appear. The options are: Save to File–Saves
the key to a user-selected file. Replace from File–Replaces the current key
with a key from a user-selected file. Append from File–Adds a key to the
current database from a user-selected file Delete–Deletes the selected key
Reset All Keys–Resets to default setting Delete All Keys–Deletes all the keys
NOTE: If you disable the Custom Mode, all the changes made are erased and the
keys restore to default settings.
Intel Software Guard Extensions screen options
Option
Description
Intel SGX Enable
This field specifies you to provide a secured environment for running
code/storing sensitive information in the context of the main OS. The options
are:
Disabled Enabled Software Controlled (default)
Enclave Memory Size
This option sets SGX Enclave Reserve Memory Size. The options are: 32 MB 64 MB 128 MB
Performance screen options
Option
Multi Core Support
Description
This field specifies whether the process has one or all cores enabled. The
performance of some applications improve with the additional cores. This
option is enabled by default. Allows you to enable or disable multi-core
support for the processor. The installed processor supports two cores. If you
enable Multi Core Support, two cores are enabled. If you disable Multi Core
Support, one core is enabled. All (enabled by default)
20
System setup
Option
Intel SpeedStep
Description
1 2 3 Allows you to enable or disable the Intel SpeedStep feature.
Enable Intel SpeedStep
Default setting: The option is enabled.
C-States Control Allows you to enable or disable the additional processor sleep states. C states Default setting: The option is enabled.
Intel TurboBoost Allows you to enable or disable the Intel TurboBoost mode of the processor. Enable Intel TurboBoost (default)
Power Management screen options
Option
AC Recovery
Enable Intel Speed Shift Technology Auto On Time
Deep Sleep Control
USB Wake Support
Wake on LAN/ WLAN
Description
Allows you to enable or disable the computer from turning on automatically
when an AC adapter is connected. Power Off (default) Power On Last Power State
This option is used to enable or disable the Intel speed shift technology
support. The option is enabled by default.
Allows you to set the time at which the computer must turn on automatically.
The options are: Disabled Every Day Weekdays Select Days
Default setting: Disabled
Allows you to aggressive the system is at conserving power while Shut down
(S5) or in Hybernate (S4) mode. Disabled (default) Enabled in S5 only Enabled
in S4 and S5
Allows you to enable USB devices to wake the system from Standby. NOTE: This
feature is only functional when the AC power adapter is connected. If the AC
power adapter is removed during Standby, the system setup removes power from
all the USB ports to conserve battery power.
Enable USB Wake Support
Default setting: The option is enabled..
Allows you to enable or disable the feature that powers on the computer from
the Off state when triggered by a LAN signal. Disabled: This option is enabled
by default. LAN Only WLAN Only LAN or WLAN LAN with PXE Boot
System setup
21
Option
Block Sleep
Description
This option lets you block entering to sleep (S3 state) in operating system
environment. Block Sleep (S3 state) Default setting: This option is disabled
POST Behavior screen options
Option
Description
Numlock LED
This option specifies whether the NumLock LED should be on when the system boots. Enable Numlock LED: The option is enabled.
Keyboard Errors This option option specifies whether the keyboard related errors are reported when it boots. Enables Keyboard Error Detection: The option is enabled by default.
Fastboot
Allows you to speed up the boot process by bypassing some of the compatibility steps. The options are: Minimal Thorough (default) Auto
Extend BIOS POST Time
This option created an additional pre-boot delay. 0 seconds (default) 5 seconds 10 seconds
Full Screen Logo . This option displays full screen logo if your image match screen resolution. The option Enable Full Screen Logo is not selected by default.
Warnings and Errors
Prompt on Warnings and Errors (default) Continue on Warnings Continue on Warnings and Errors
Virtualization support screen options
Option
Description
Virtualization
Allows you to enable or disable the Intel Virtualization Technology. Enable Intel Virtualization Technology (default).
VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from
utilizing the additional hardware capabilities provided by Intel®
Virtualization technology for direct I/O.
Enable VT for Direct I/O – enabled by default.
Wireless screen options
Option
Wireless Device Enable
Description
Allows you to enable or disable internal wireless devices. WLAN/WiGig
(default) Bluetooth (default)
22
System setup
Advanced configuration options
Option
ASPM
Description
Allows you to set the ASPM level. Auto (default) Disabled L1 Only
Maintenance screen options
Option
Description
Service Tag Asset Tag
Displays the Service Tag of your computer. Allows you to create a system asset tag if an asset tag is not already set. This option is not set by default.
SERR Messages This field controls the SERR message mechanism. Some graphic
card required the SERR message. Enable SERR Messages (default)
BIOS Downgrade This field controls flashing of the system firmware to pervious
revisions. Allows BIOS Downgrade (Enabled by default)
Data Wipe
This field enables user to erase data from all internal storage device.
BIOS Recovery
First Power On Date
Allows you to recover from certain corrupted BIOS conditions from a recover
file on the user primary hard drive or an external USB key. Enabled by
default.
This option lets you set Ownership date. This option is disabled by default.
System Log screen options
Option
BIOS Events
Description
Allows you to view and clear the System Setup (BIOS) POST events.
SupportAssist System Resolution
Option
Auto OS Recovery Threshold
SupportAssist OS Recovery
Description
Allows you to control the automatic boot flow for SupportAssist System.
Options are: Off 1 2 (Enabled by default) 3
Allows you to recover the SupportAssist OS Recovery ( Enabledby default)
Updating the BIOS in Windows
It is recommended to update your BIOS (System Setup) when you replace the
system board or if an update is available. NOTE: If BitLocker is enabled, it
must be suspended prior to updating the system BIOS, and then re enabled after
the BIOS update is completed.
System setup
23
CAUTION: If BitLocker is not suspended before updating the BIOS, the next time
you reboot the system it will not recognize the BitLocker key. You will then
be prompted to enter the recovery key to progress and the system will ask for
this on each reboot. If the recovery key is not known this can result in data
loss or an unnecessary operating system re-install. For more information on
this subject, see Knowledge Base Article:
https://www.dell.com/support/kbdoc/000134415/.
1. Restart the computer. 2. Go to Dell.com/support.
Enter the Service Tag or Express Service Code and click Submit. Click Detect
Product and follow the instructions on screen. 3. If you are unable to detect
or find the Service Tag, click Choose from all products. 4. Choose the
Products category from the list.
NOTE: Choose the appropriate category to reach the product page.
5. Select your computer model and the Product Support page of your computer
appears. 6. Click Get drivers and click Drivers and Downloads.
The Drivers and Downloads section opens. 7. Click Find it myself. 8. Click
BIOS to view the BIOS versions. 9. Identify the latest BIOS file and click
Download. 10. Select your preferred download method in the Please select your
download method below window, click Download File.
The File Download window appears. 11. Click Save to save the file on your
computer. 12. Click Run to install the updated BIOS settings on your computer.
Follow the instructions on the screen.
System and setup password
Table 17. System and setup password Password type System password Setup password
Description Password that you must enter to log on to your system.
Password that you must enter to access and make changes to the BIOS settings
of your computer.
You can create a system password and a setup password to secure your computer. CAUTION: The password features provide a basic level of security for the data on your computer. CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended. NOTE: System and setup password feature is disabled.
Assigning a system setup password
You can assign a new System or Admin Password only when the status is in Not
Set. To enter the system setup, press F2 immediately after a power-on or
reboot. 1. In the System BIOS or System Setup screen, select Security and
press Enter.
The Security screen is displayed. 2. Select System/Admin Password and create a
password in the Enter the new password field.
Use the following guidelines to assign the system password: A password can
have up to 32 characters.
24
System setup
The password can contain the numbers 0 through 9. Only lower case letters are
valid, upper case letters are not allowed. Only the following special
characters are allowed: space, (“), (+), (,), (-), (.), (/), (;), ([), (),
(]), (`). 3. Type the system password that you entered earlier in the Confirm
new password field and click OK. 4. Press Esc and a message prompts you to
save the changes. 5. Press Y to save the changes. The computer reboots.
Deleting or changing an existing system setup password
Ensure that the Password Status is Unlocked (in the System Setup) before
attempting to delete or change the existing System and Setup password. You
cannot delete or change an existing System or Setup password, if the Password
Status is Locked.
To enter the System Setup, press F2 immediately after a power-on or reboot. 1.
In the System BIOS or System Setup screen, select System Security and press
Enter.
The System Security screen is displayed. 2. In the System Security screen,
verify that Password Status is Unlocked. 3. Select System Password, alter or
delete the existing system password and press Enter or Tab. 4. Select Setup
Password, alter or delete the existing setup password and press Enter or Tab.
NOTE: If you change the System and/or Setup password, re enter the new
password when prompted. If you delete the System and Setup password, confirm
the deletion when prompted.
5. Press Esc and a message prompts you to save the changes. 6. Press Y to
save the changes and exit from System Setup.
The computer restarts.
System setup
25
5
Software
Topics:
· Supported operating systems · Downloading Windows drivers
Supported operating systems
Table 18. Supported operating systems Features Supported operating systems
Windows 10
Others
Specifications
Description
Windows 10 64-bit Windows 10 64-bit Professional Windows 10 64-bit National
Academic (STF)
Ubuntu
Downloading Windows drivers
1. Turn on the . 2. Go to Dell.com/support. 3. Click Product Support, enter
the Service Tag of your , and then click Submit.
NOTE: If you do not have the Service Tag, use the auto detect feature or
manually browse for your model.
4. Click Drivers and Downloads. 5. Select the operating system installed on
your . 6. Scroll down the page and select the driver to install. 7. Click
Download File to download the driver for your . 8. After the download is
complete, navigate to the folder where you saved the driver file. 9. Double-
click the driver file icon and follow the instructions on the screen.
Intel chipset drivers
Verify if the Intel chipset drivers are already installed in the system.
26
Software
Serial IO driver
Verify if the drivers for Touchpad, IR camera, and keyboard and are installed.
Software
27
Figure 1. Serial IO driver
USB drivers
Verify if the USB drivers are already installed in the computer.
Network drivers
Install the WLAN and Bluetooth drivers from the Dell support site.
Table 19. Network drivers Before installation
After installation
Realtek Audio
Verify if audio drivers are already installed in the computer. Table 20.
Realtek audio Before Installation
After Installation
28
Software
Serial ATA drivers
Install the latest Intel Rapid Storage driver for best performance. Using the
default Windows storage drivers is not recommended. Verify if the default
serial ATA drivers are installed in the computer.
Software
29
6
Getting help
Topics:
· Contacting Dell
Contacting Dell
NOTE: If you do not have an active Internet connection, you can find contact
information on your purchase invoice, packing slip, bill, or Dell product
catalog. Dell provides several online and telephone-based support and service
options. Availability varies by country and product, and some services may not
be available in your area. To contact Dell for sales, technical support, or
customer service issues: 1. Go to Dell.com/support. 2. Select your support
category. 3. Verify your country or region in the Choose a Country/Region
drop-down list at the bottom of the page. 4. Select the appropriate service or
support link based on your need.
30
Getting help
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>