Shelly WiFi Humidity And Temperature Sensor User Guide
- June 7, 2024
- Shelly
Table of Contents
Shelly WiFi Humidity And Temperature Sensor User Guide
This document contains important technical and safety information about the
device and its safety use and installation. Before beginning the installation,
please read this guide and any other documents accompanying the device
carefully and completely. Failure to follow the installation procedures could
lead to malfunction, danger to your health and life, violation of the law or
refusal of legal and/or commercial guarantee (if any). Allterco Robotics is
not responsible for any loss or damage in case of incorrect installation or
improper operation of this device due to failure of following the user and
safety instructions in this guide.
Shelly® H&T main function is to measure and indicate humidity and temperature
for the room/area where it is placed.
The device can also be used as action trigger to other devices for your home
automation. Shelly® H&T may work as standalone device or as an addition to a
home automation controller.
Shelly® H&T is battery operated device, or it can be operated constantly
connected to power supply through USB power supply accessory. USB power supply
accessory is not included to the Shelly® H&T product, and it is available for
purchase separately.
Specification
- Battery Type: 3V DC – CR123A (Battery not included)
- Estimated battery Life: Up to 18 months
- Humidity measurement range: 0~100% (±5%)
- Temperature measurement range: -40°C÷60 °C (± 1°C)
- Working temperature: -40°C÷60 °C
- Radio signal power: 1mW
- Radio protocol: WiFi 802.11 b/g/n
- Frequency: 2412-2472 МHz; (Max. 2483,5 MHz)
- RF output power 9,87dBm
- Dimensions (HxWxL): 35x45x45 mm
- Operational range:
- up to 50 m outdoors
- up to 30 m indoors
- Electrical consumption:
- “Sleep” mode ≤70uA
- “Awake” mode ≤250mA
Introduction to Shelly
Shelly® is a line of innovative Devices, which allow remote control of electric appliances through a mobile phone, tablet, PC, or home automation system. All devices use WiFi connectivity and can be controlled from the same network or through remote access (any internet connection). Shelly® may work standalone on the local WiFi network, without being managed by a home automation controller, or it can also work through cloud home automation services. Shelly devices can be accessed remotely from any place the User has Internet connectivity. Shelly® has an integrated web server, through which the User may adjust, control and monitor the Device. Shelly® Devices have two WiFi modes – Access Point (AP) and Client mode (CM). To operate in Client Mode, a WiFi router must be located within the range of the Device. Shelly® Devices can communicate directly with other WiFi devices through HTTP protocol. An API can be provided by the Manufacturer. Shelly® Devices may be available for monitor and control even if the User is outside the range of the local WiFi network, as long as the devices are connected to a WiFi router and the Internet. The cloud function could be used, which is activated through the web server of the Device or the settings in the Shelly Cloud mobile application. The User can register and access Shelly Cloud using either Android or iOS mobile application, or with any internet browser at https://my.shelly.cloud/
Installation Instructions
CAUTION! Use the Device only with batteries which comply with all applicable regulations. Inappropriate batteries may cause a short circuit in the Device, which may damage it.
**** CAUTION! Do not allow children to play with the device, especially with the Power Button. Keep the devices for remote control of Shelly (mobile phones, tablets, PCs) away from children.
Battery placement and Button controls
Twist the bottom cover of the device counterclockwise to open. Insert the
battery inside before placing the device at the desired place.
Power Button is located inside the device and can be accessed when device
cover is open. (when using USB power supply accessory power button is
accessible through a hole at the bottom of the device with a pin)
Press the Button to turn on AP mode of the device. The LED indicator located
inside of the device should flash slowly.
Press the Button again, the LED indicator will turn off and device will be in
„Sleep“ mode.
Press and hold the button for 10 seconds for Factory Settings Reset.
Successful factory reset turns on the LED indicator to flash slowly.
LED Indicator
- LED flashing slowly – AP Mode
- LED constant light – STA Mode (Connected to Cloud)
- ED flashing quickly
- STA Mode (No Cloud) or
- FW Update (while in STA mode and connected to Cloud)
Compatibility
Shelly® devices are compatible with Amazon Alexa and Google Assistant, as well as with most 3rd party home automation platforms. Please see our step-by-step guides on: https://shelly.cloud/support/compatibility/
Additional Features
Shelly® allows control via HTTP from any other device, home automation
controller, mobile app or server. For more information about the REST control
protocol, please visit: https://shelly.cloud or send a request to
support@shelly.cloud
Declaration of conformity
Hereby, Allterco Robotics EOOD declares that the radio equipment type for Shelly H&T is in compliance with Directive 2014/53/EU, 2014/35/EU, 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: https://shelly.cloud/knowledge-base/devices /shelly-ht/
General information and guarantees
Manufacturer: Allterco Robotics EOOD
Address: Bulgaria, Sofia, 1407, 103 Cherni vrah Blvd.
Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
Web: https://shelly.cloud
Changes in the contact data are published by the Manufacturer at the official
website of the Device https://shelly.cloud
All rights to trademark Shelly®, and other intellectual rights associated with this Device belong to Allterco Robotics EOOD.
The Device is covered by legal guarantee in accordance with the applicable EU consumer protection legislation. Additional commercial guarantee might be provided by the individual merchant under express statement. All guarantee claims shall be addressed to the seller, from whom the device was purchased.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>