DOMETIC 10-Series Refrigeration Compressor Refrigerator User Manual
- June 7, 2024
- Dometic
Table of Contents
DOMETIC 10-Series Refrigeration Compressor Refrigerator
© 2021 Dometic Group. The visual appearance of the contents of this manual is protected by copyright and design law. The underlying technical design and the products contained herein may be protected by design, patent or be patent pending. The trademarks mentioned in this manual belong to Dometic Sweden AB. All rights are reserved.
Explanation of symbols
| WARNING!
Safety instruction: Indicates a hazardous situation that, if not avoided,
could result in death or serious injury.
---|---
| CAUTION!
Safety instruction: Indicates a hazardous situation that, if not avoided,
could result in minor or moderate injury.
|
NOTICE!
Indicates a situation that, if not avoided, can result in property damage.
|
NOTE
Supplementary information for operating the product.
Safety instructions
This product is only suitable for the intended purpose and application in accordance with these instructions.
This manual provides information that is necessary for proper installation and/or operation of the product. Poor installation and/or improper operating or maintenance will result in unsatisfactory performance and a possible failure.
The manufacturer accepts no liability for any injury or damage to the product resulting from:
-
Incorrect assembly or connection, including excess voltage
-
Incorrect maintenance or use of spare parts other than original spare parts
provided by the manufacturer -
Alterations to the product without express permission from the manufacturer
-
Use for purposes other than those described in this manual
Dometic reserves the right to change product appearance and product specifications.
General safety
WARNING! Failure to obey these warnings could result in death or serious injury.
Electrocution hazard
- Ensure that the device has been installed by a qualified technician in accordance with the Dometic installation manual.
- Do not operate the device if it is visibly damaged.
- If this device’s power cable is damaged, it must be replaced by the manufacturer, a service agent or a similarly qualified person in order to prevent safety hazards.
- This device may only be repaired by qualified personnel. Inadequate repairs may cause serious hazards.
Explosion hazard
- Do not store any explosive substances, such as spray cans with propellants, in the device.
Health hazard
- This device can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the device in a safe way and understand the hazards involved.
- Children shall not play with the device.
- Cleaning and user maintenance shall not be made by children without supervision.
- Children aged from 3 to 8 years are allowed to load and unload refrigerating devices.
Risk of child entrapment
- Make sure that the shelves are mounted and secured so that children cannot lock themselves in the device.
- Before disposing of your old refrigerator: Dismantle the drawers. Leave the shelves in the refrigerator so that children cannot climb inside.
CAUTION! Failure to obey these cautions could result in minor or moderate injury.
Risk of crushing
- Do not put your fingers into the hinge. Health hazard · Foodstuff may only be stored in its original packaging or in suitable containers.
NOTICE! Damage hazard
-
Check that the voltage specification on the type plate is the same as that of the power supply.
-
If your vehicle does not have a battery undervoltage cutout, disconnect the device or switch it off when you turn off the engine. Otherwise you may discharge the battery.
-
The device is not suitable for storing substances which are caustic or contain solvents.
-
Keep the drainage outlet clean at all times.
-
Do not open the refrigerant circuit under any circumstances.
-
Do not transport the device in a horizontal position, so that no oil can leak out of the compressor and through this damage the refrigerant circuit.
-
Make sure that the refrigerant circuit is not damaged during transportation. The refrigerant in the refrigerant circuit is highly flammable. In the event of any damage to the refrigerant circuit:
– Avoid naked flames and sparks.
– Air the room well. -
Set up the device in a dry location where it is protected against splashing water.
Operating the device safely
DANGER! Failure to obey these warnings will result in death or serious injury.
Electrocution hazard
- Do not touch exposed cables with your bare hands.
CAUTION! Failure to obey these cautions could result in minor or moderate injury.
Electrocution hazard
-
Before starting the device, ensure that the power supply line and the plug are dry. Health hazard · Make sure that you only put items in the device which may be chilled at the selected temperature.
-
Food may only be stored in its original packaging or in suitable containers.
-
Opening the door for long periods can cause significant increase of the temperature in the compartments of the device.
-
Clean regularly surfaces that can come in contact with food and accessible drainage systems.
-
Store raw meat and fish in suitable containers in the device, so that it is not in contact with or can drip onto other food.
-
If the device is left empty for long periods:
– Switch off the device.
– Defrost the device.
– Clean and dry the device.
– Leave the door open to prevent mould developing within the device. -
If the refrigerator is exposed to a room temperature of below +10 °C for an extended period of time, a uniform temperature cannot be guaranteed in the freezer compartment. This can lead to an increase of the freezer compartment temperature and the goods stored in it may defrost.
Risk of injury
- The device door or the freezer door can completely detach from the device if used incorrectly. Push the doors closed until you hear a clear click at the top and bottom.
- Do not lean on the open device door.
NOTICE! Damage hazard
- If the door is not locked correctly on the opposite side, push on that side at the top and the bottom until it locks in place.
- Only store heavy objects such as bottles or cans in the device door, in the vegetable compartment or on the bottom shelf.
- Do not use electrical devices inside the cooling device unless they are recommended by the manufacturer for that purpose.
- Do not place it near naked flames or other heat sources (heaters, direct sunlight, gas ovens etc.).
- Ensure that the ventilation vents are not covered.
- Do not fill the inner container with ice or fluid.
- Never immerse the device in water.
- Protect the device and the cable against heat and moisture.
- Make sure that foodstuffs do not touch the walls of the cooling area.
NOTE
- Ask your vehicle manufacturer if the battery management of your vehicle shuts down the devices to protect the battery.
- Put the device door and the freezer door into the winter position if you are not going to use the device for a longer period of time. This prevents mold from forming.
- For ambient temperatures of +15 °C to +25 °C, select the average temperature setting.
Installing the refrigerator
| CAUTION! Health hazard
To avoid a hazard due to instability of the device, it must be fixed in
accordance with the instructions
---|---
|
You find the instructions for changing the door stop and the decorative plate
online at:
documents.dometic.com/?object_id=63258
---|---
The device is suitable for installation in:
- caravans
- motor homes
Preparing the installation
| CAUTION! Risk of injury
The device has sharp edges and gloves should be used duringinstallation
---|---
| NOTICE! Damage hazard
- The refrigerator may not be installed in the rear of mobile homes with the door pointing in the direction of travel.
- Leave the device in a vertical position for at least 3 hours before starting up for the first time.
---|---
| NOTE
- In Camper Vans an undercounter unit can be installed with the door pointing in the direction of travel, as long as it is installed next to the sliding door and behind the co-driver’s seat.
- If the compressor fridge replaces an absoption unit, you have to make sure, that the external ventilation grills are completely closed, otherwise there is the risk, that the compressor will not run at low ambient temperature (~below 0 °C).
---|---
When installing the refrigerator, note the following:
-
Ensure that the floor is solid and level. Park the vehicle horizontally for this purpose.
-
The refrigerator must be installed so that it is easily accessible for service work easy to de-install and install can be easily removed from the vehicle
-
The refrigerator must be installed in a recess so that it stands secure when the vehicle is in motion. Note the dimensions in fig. , and fig. , for this purpose.
-
Also note the following recess dimension (fig. ):
| RC10.4(S)(T).70| RC10.4(S)(T).90| RC10.4P.100
---|---|---|---
Refrigerator height (A)| 821 mm| 975 mm|
900 mm
Refrigerator width (B)
| 420 mm| 420 mm| 420 mm
(rear compressor)
590 mm
(side compressor)
Refrigerator depth (C) (excludes control knob 5 mm)| 450 mm| 485 mm|
655 mm
(rear compressor)
485 mm
(side compressor)
Recess height (H)
| 823 mm| 977 mm| 902 mm
Recess width (W)| 425 mm| 425 mm|
425 mm
(rear compressor)
595 mm
(side compressor)
Recess depth (D)
| 452 mm| 487 mm|
657 mm
(rear compressor)
487 mm
(side compressor
|
RCL10.4(S)(T)
| RCD10.5(S)(T)|
RCD10.5X(S)(T)
---|---|---|---
Refrigerator height (A)
| 1293 mm| 1282 mm| 1282 mm
Refrigerator width (B)| 420 mm| 523 mm|
523 mm
Refrigerator depth (C)
(excludes control knob 5 mm)
| 595 mm595 mm| 565 mm| 620 mm
Recess height (H)| 1296 mm| 1285 mm|
1285 mm
Recess width (W)
| 425 mm| 528 mm| 528 mm
Recess depth (D)| 598 mm| 568 mm|
623 mm
|
RCS10.5(S)(T)
|
RCS10.5X(S)(T)
---|---|---
Refrigerator height (A)
| 821 mm| 821 mm
Refrigerator width (B)| 523 mm|
523 mm
Refrigerator depth (C)
(excludes control knob 5 mm)
| 555 mm| 610 mm
Recess height (H)| 824 mm|
824 mm
Recess width (W)
| 528 mm| 528 mm
Recess depth (D)| 558 mm|
613 mm
Installing the condensation drain
| NOTE
- Condensation can form inside the refrigerator due to frequent door opening, incorrectly stored food or food that is stored when it is too warm.
- Condensation must be drained with a constant slope.
---|---
Install the condensation drain as follows:
➤ Run the condensation hose from the refrigerator through an opening in the floor which goes outside.
Connecting the power supply
| NOTICE!
- The electrical installation and repairs may only be performed by a specialist in accordance with the applicable national regulations and standards.
- To avoid voltage loss and therefore a drop in performance, the cable should be kept as short as possible and should not be interrupted if possible. For this reason avoid additional switches, plugs or power strips.
- Before connecting check whether the operating voltage and the battery voltage correspond (see type plate).
---|---
-
➤ Determine the required cross section of the cable in relation to the cable length according to fig. ,
-
➤ Connect the cables to the AMP connector of the refrigerator (fig. , ).
-
➤ Connect the other ends of the cables to the 12 Vg power supply:
| NOTICE!
- Make sure the polarity is correct.
- Fit the positive (+) cable with a 10 A fuse.
---|---
– as directly as possible
– rd (red): with a fuse protection (10 A) fitted to the positive (+) pole
– bk (black): to the negative (–) pole
Securing the refrigerator
| WARNING! Fire Hazard
- When positioning the device, ensure the supply cord is not trapped or damaged.
- Do not locate multiple portable socket-outlets or portable power supplies at the rear of the device.
---|---
| CAUTION!
Only screw through the bushings provided, otherwise foamed components, such as
cables, can be damaged.
---|---
| NOTE
- Attach the side walls or the attached strips so that the screws are tight, even under increased loads (while driving).
- The refrigerator is designed to provide a regulated air flow. The manufacturer does not recommend to leave additional space between the refrigerator and the recess walls.
---|---
-
➤ Move the refrigerator into its final location with the front flange sitting tight against the recess front.
-
➤ Fasten the screws (fig. , ) through the plastic bushings in the sides of the refrigerator, and further into the wall.
-
➤ Put the caps onto the screw heads.
Installing the control panel of RC10.4P.100
- ➤ Install the control panel as shown (fig. , ).
Technical data
For the current EU declaration of conformity for your device please refer to
the respective product page on dometic.com or contact the manufacturer
directly (see dometic.com/dealer).
This device complies with UN ECE Regulation R10.
This product contains fluorinated greenhouse gases.
The cooling unit is hermetically sealed.
|
RC 10.4(S)(T).70
| RC 10.4(S)(T).90|
RC 10.4P.100
---|---|---|---
Capacity
Gross capacity:
Refrigerator compartment:
Freezer compartment:
Total net capacity:
Excluding freezer compartment
Gross capacity:
Net capacity:|
62 l
54.5 l
7.5 l 62 l
69 l
64 l
| 86 l
75.5 l
7.5 l 83 l
90 l
85 l|
94 l
81 l
9l 90 l
98 l
93 l
Connection voltage:|
12 Vg
| 12 Vg|
12 Vg
Average power input:|
42 W
| 45 W|
48 W
Energy consumption PERFORMANCE mode:|
0.45 kWh/24 h
37.5 Ah/24 h
| 0.45 kWh/24 h
37.5 Ah/24 h|
0.46 kWh/24 h 38 Ah/24 h
Climate class:|
T
| T|
T
Coolant:|
R134a/40 g
| R134a/43 g|
R134a/47 g
CO2 equivalent:|
0.057 t
| 0.061 t|
0.065 t
Global warming potential (GWP):|
1430
| 1430|
1430
Noise emission (EN60704) PERFORMANCE mode:
QUIET mode:|
42 dB(A)
39 dB(A)
| 42 dB(A)
39 dB(A)|
42 dB(A)
39 dB(A)
Dimensions H x W x D (in mm):|
821 x 420 x 450
| 975 x 420 x 485|
902 x 420 x 655
(rear compressor) 902x 590x 485
(side compressor)
Weight:|
19.5 kg
| 21.4 kg|
21 kg
Inspection/certification:|
| RCL 10.4(S)(T)| RCD 10.5(S)(T)| RCD 10.5X(S)(T)
---|---|---|---
Capacity
Gross capacity:
Refrigerator compartment:
Freezer compartment:
Total net capacity:
Excluding freezer compartment
Gross capacity: Net capacity:|
133 l|
116 l
12 l
128 l
139 l
134 l
| 153 l
118 l
29 l
147 l
–
–|
177 l
142 l
35 l
171 l
–
–
Connection voltage:|
12 Vg
| 12 Vg|
12 Vg
Average power input:|
54 W
| 54 W|
54 W
Energy consumption PERFORMANCE mode:|
0.61 kWh/24 h 51 Ah/24 h
| 0.70 kWh/24 h 58 Ah/24 h|
0.72 kWh/24 h 60 Ah/24 h
Climate class:|
ST
| ST|
ST
Coolant:|
R134a / 40 g
| R134a/44 g|
R134a/44 g
CO2 equivalent:|
0.057 t
| 0.057 t|
0.057 t
Global warming potential (GWP):|
1430
| 1430|
1430
Noise emission (EN60704) PERFORMANCE mode:
QUIET mode:
|
42 dB(A)
39 dB(A)
| 42 dB(A)
39 dB(A)|
42 dB(A)
39 dB(A)
Dimensions H x W x D (in mm):|
1293 x 420 x 595
| 1282 x 523 x 565|
1282 x 523 x 620
Weight:| 32 kg| 36.5 kg| 39.5 kg
Inspection/certification:|
| RCS 10.5(S)(T)| RCS 10.5X(S)(T)
---|---|---
Capacity
Gross capacity: Refrigerator compartment: Freezer compartment:
Total net capacity:
Excluding freezer compartment
Gross capacity: Net capacity:|
78 l
69.1 l
9.2 l 78 l
83 l
83 l
|
92 l
80.3 l
12.1 l 92 l
98 l
98 l
Connection voltage:|
12 V
|
12 V
Average power input:|
5.9 A
|
5.5 A
Energy consumption PERFORMANCE mode:| 0.42 kWh/24 h 35 Ah/24 h| 0.43 kWh/24 h
35.5 Ah/24 h
Climate class:|
N, ST
|
N, ST
Coolant:|
R600a / 24 g
|
R600a / 23 g
CO2 equivalent:|
0.000072 t
|
0.000069 t
Global warming potential (GWP):|
3
|
3
Noise emission (EN60704)
With air channel:
PERFORMANCE mode:
QUIET mode:
Without air channel:
PERFORMANCE mode:
QUIET mode:|
44 dB(A)
39 dB(A)
42 dB(A)
38 dB(A)
|
44 dB(A)
39 dB(A)
42 dB(A)
38 dB(A)
Dimensions H x W x D (in mm):|
821 x 523 x 555
|
821 x 523 x 610
Weight:|
24.5 kg
|
25 kg
Inspection/certification:|
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>