neue NGI96NX Cooker Hood Instruction Manual

June 7, 2024
Neue

NGI96NX
Cooker Hood
Instruction Manual

neue NGI96NX Cooker Hood

SAFETY INSTRUCTIONS

This manual explains the proper installation and use of your cooker hood, please read it carefully before using it even if you are familiar with the product. The manual should be kept in a safe place for future reference. These instructions shall also be available in an alternative format, e.g. on a website or on request from the user in a format such as a DVD.

Never to do:

● Do does not try to use the cooker hood without the grease filters or if the filters are excessively greasy!

●Do not install above a cooker with a high-level grill.

●Do not leave frying pans unattended during use because overheated fats or oils might catch fire.

●Never leave naked flames under the cooker hood.

neue NGI96NX Cooker Hood figure 1

●If the cooker hood is damaged, do not attempt to use it.
●Do not flambé under the cooker hood.
●CAUTION: Accessible parts may become hot when used with cooking appliances.
●The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the cooker hood. (When the cooker hood is located above a gas appliance, this distance shall be at least 65 cm)
●The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.

neue NGI96NX Cooker Hood figure 2

●Always put lids on pots and pans when cooking on a gas cooker.
●When in extraction mode, the air in the room is being removed by the cooker hood. Please make sure that proper ventilation measures are being observed. The cooker hood removes odors from the room but not steam.
●Cooker hood is for domestic use only.

neue NGI96NX Cooker Hood figure 3

●If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
●This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

neue NGI96NX Cooker Hood figure 4

Always to do:

● Important! Always switch off the electricity supply at the mains during installation and maintenance such as light bulb replacement.
●The cooker hood must be installed in accordance with the installation instructions and all measurements followed.
●All installation work must be carried out by a competent person or qualified electrician.
●Please dispose of the packing material carefully. Children are vulnerable to it.
● Pay attention to the sharp edges inside the cooker hood especially during installation and cleaning.
●When the cooker hood is located above a gas appliance, the minimum distance between the supporting surface for the cooking vessels on the hob and the lowest  part of the cooker hood that distance must be: Gas cookers: 75 cm Electric cookers: 65 cm Coal or oil cookers: 75 cm
●Make sure the ducting has no bends sharper than 90 degrees as this will reduce the efficiency of the cooker hood.
●Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards
●Warning: Before obtaining access to terminals, all supply circuits must be disconnected.
● Caution: The appliance and its accessible parts can become hot during operation. Be careful to avoid touching the heating elements. Children younger than 8 years old should stay away unless they are under permanent supervision.
● There shall be adequate ventilation of the room when the cooker hood is used at the same time as appliances burning gas or other fuels.
●There is a fire risk if cleaning is not carried out in accordance with the instructions
●Regulations concerning the discharge of air have to be fulfilled.
●Clean your appliance periodically by following the method given in the chapter MAINTENANCE.
●For safety reasons, please use only the same size of fixing or mounting screws which is recommended in this instruction manual.
●Regarding the details about the method and frequency of cleaning, please refer to the maintenance and cleaning section in the instruction manual.
●Cleaning and user maintenance shall not be made by children without supervision.
●When the cooker hood and appliances supplied with energy other than electricity are simultaneously in operation, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar).
●WARNING: Danger of fire: do not store items on the cooking surfaces.
●A steam cleaner is not to be used.
●NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.

INSTALLATION (VENT OUTSIDE)
MOUNTING OF THE V-FLAP

If the cooker hood does not have an assembled V-flap 1, you should mount the half parts to its body. The images only show an example of how to mount the V- flap, the outlet may be varied according to different models and configurations.
To mount the V-flap 1 you should:

  • Mount two half-parts 2 into the body 6
  • a pin 3 should be top oriented;
  • the axis 4 should be inserted in the holes 5 on the body;
  • repeat all the operations for the 2nd half-part

neue NGI96NX Cooker Hood figure 5

INSTALLATION

If you have an outlet to the outside, your cooker hood can be connected as below picture by means of an extraction duct. (enamel, aluminum, flexible pipe or inflammable material with an interior diameter of 150mm)

neue NGI96NX Cooker Hood figure 6

  1. Before installation, turn the unit off and unplug it from the outlet.

  2. The cooker hoods should be placed at a distance of 65-75cm from the cooking surface for the best effect. See Pic 1
    neue NGI96NX Cooker Hood figure 9

  3. The ceiling must can bear at least 40kgs weight, and the thickness of the ceiling must be ≧30MM, see pic 2, drill 1*170mm round hole in the ceiling.

  4. According to the hanging board, drill 12 holes in the ceiling, see pic 2, 12pcs of ST640mm big flat screws will be used to fix the hanging board on the ceiling,  and then 8pcs of M410 screws and M4 nut with gasket will be used to connect the angle iron into the hanging board. See pic 1, calculated the length of the  angle iron, and 16pcs M4*10 big flat screws and M4 nut with gasket will be used to connect the angle iron and another angle iron ( the overlap length of angle  iron can not less 100MM)

  5. Let the one side of the expansion pipe go outside through the hole of 170MM, see pic 3.

  6. 4pcs ST4*8 big flat screws will be used to connect the inside chimney into the hanging board, then put on the outside chimney, two hooks will be used to put up the outside chimney in order for the next installation, see pic 4.

  7. 4pcs ST4*8 big flat screws will be used to install the outlet, see pic 5.

  8. Adjust the 4 glass screws to check whether the glass and the cooker hood body connected well and fixed, see pic 6.
    neue NGI96NX Cooker Hood figure 11

  9. Hold up the hood, 16pcs M4*10 big flat screws will be used to connect the hood body into angle iron, see pic 7.

  10. Put the expansion pipe on the outlet; after ensuring all the things ok, put down the hook, take from the outside chimney, all the installation is finished, see pic 9.

neue NGI96NX Cooker Hood figure 12.

HINTS FOR EXHAUST DUCT INSTALLATION

The following rules must be strictly followed to obtain optimal air extraction:

  • Keep expansion pipe short and straight.
  • Do not reduce the size or restrict the expansion pipe.
  • When using an expansion pipe always install the pipe pulled taut to minimize pressure loss.
  • Failure to observe these basic instructions will reduce the performance and increase noise levels of the cooker hood.
  • Any installation work must be carried out by a qualified electrician or competent person.
  • Do not connect the ducting system of the hood to any existing ventilation system which is being used for any other appliance, such as a warmer tube, gas tube,  hot wind tube.
  • The angle of the bend of the expansion pipe should not be less than 120º; you must direct the pipe horizontally, or, alternatively, the pipe should go up from the initial point and should be led to an outer wall.
  • After the installation, make sure that the cooker hood is level to avoid grease collection at on end.
  • Ensure the expansion pipe selected for installation complies with relevant standards and is fire retardant.

neue NGI96NX Cooker Hood figure 13

WARNING:
| ⇒ For safety reasons, please use only the same size of fixing or mounting screws which are recommended in this instruction manual.
⇒Failure to install the screws or fixing the device in accordance with these instructions may result in electrical hazards.
---|---

Start Using Your Cooker Hood
Electronic button

  1. Press the button “Low”, the inner indicator light of the switch starts shining, the motor is running at low speed. Press the button again, the motor stop.
  2. Press the button “Mid”, the inner indicator light of the switch starts shining, the motor is running at medium speed. Press the button again, the motor stop.
  3. Press the button “High”, the inner indicator light of the switch starts shining, the motor is running at high speed. Press the button again, the motor stop.
  4. Press the button “Light”, both lights start shining . Press the button again, the lights are switched off then.

neue NGI96NX Cooker Hood figure 14

TROUBLESHOOTING

Fault

| Possible Cause|

Solution

---|---|---

Light on, but the motor does not work

| Fan switch turned off| Select a fan switch position.
Fan switch failed| Contact service center.
Motor failed| Contact service center.
Light does not work, the motor does not work| House fuses blown| Reset/replace fuses.
Power cord lose or disconnected| Refit cord to a power outlet. Switch power outlet on.
Oil leakage| One way valve and the air ventilation entrance are not tightly sealed| Takedown the one-way valve and seal with sealant.
Leakage from the connection of U-shaped section and cover| Take the U-shaped section down and seal.
Lights not working| Broken/Faulty globes| Replace globes as per this instruction.
Insufficient suction| The distance between the cooker hood and the gas top is too far| Refit the cooker hood to the correct distance.
The Cooker hood inclines| The fixing screw is not tight enough| Tighten the hanging screw and make it horizontal.

NOTE:
Any electrical repairs to this appliance must conform to your local, state, and federal laws. Please contact the service center if in any doubt before undertaking any of the above. Always disconnect the unit from the power source when opening the unit.

MAINTENANCE AND CLEANING

Caution:

  • Before maintenance or cleaning is carried out, the cooker hood should be disconnected from the main power supply. Ensure that the cooker hood is switched off at the wall socket and the plug removed.
  • External surfaces are susceptible to scratches and abrasions, so please follow the cleaning instructions to ensure the best possible result is achieved without damage.

GENERAL
Cleaning and maintenance should be carried out with the appliance cold especially when cleaning. Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.) on the surfaces.

STAINLESS STEEL
The stainless steel must be cleaned regularly (e.g.weekly) to ensure long life expectancy. Dry with a clean soft cloth. A specialized stainless steel cleaning fluid may be used.
NOTE:
Ensure that wiping is done along with the grain of the stainless steel to prevent any unsightly crisscross scratching patterns from appearing.

CONTROL PANEL SURFACE
The inlay control panel can be cleaned using warm soapy water. Ensure the cloth is clean and well wrung before cleaning. Use a dry soft cloth to remove any excess moisture left after cleaning.

Important
Using neutral detergents and avoid using harsh cleaning chemicals, strong household detergents or products containing abrasives,as this will affect the appliance appearance and potentially remove any printing of artwork on the control panel and will void manufacturers, warrantee.

GREASE MESH FILTERS
The mesh filters can be cleaned by hand. Soak them for about 3 minutes in water with a grease-loosening detergent then brush it gently with a soft brush. Please do not apply too much pressure, avoid damaging it. (Leave to dry naturally out of direct sunlight)

Filters should be washed separately to crockery and kitchen utensils. it is advisable not to use rinse aid.

INSTALLING GREASE MESH FILTERS

  • To install filters for the following four steps
    – Angle the filter into slots at the back of the hood.
    – Push the button on the handle of the filter.
    – Release the handle once the filter fits into a resting position.
    – Repeat to install all filters.

CARBON FILTER-not supplied

An activated carbon filter can be used to trap odors. Normally the activated carbon filter should be changed at three or six months according to your cooking habit.  The installation procedure of the activated carbon filter is as below.

  • Remove the al filter.
  • Insert the carbon filter in the rectangular hole, fitting it over the motor.
  • After inserting the front edge of the carbon filter into the slot on the cooker hood. Lower the back edge of the carbon filter, until it clicks into place at the rear of the rectangular hole. Raise the two fixing bars, until they are horizontal over the carbon filter.
  • Place the Al. filter back to position.
  • Apply a reverse procedure to uninstall the carbon filter.

neue NGI96NX Cooker Hood figure 16

NOTE:

  • Make sure the filter is securely locked. Otherwise, it would loosen and cause danger.
  • When an activated carbon filter is attached, the suction power will be lowered.

BULB REPLACEMENT

Important :
| ⊗The bulb must be replaced by the manufacturer, its service agent or similarly qualified persons.
⊗Always switch off the electricity supply before carrying out any operations on the appliance. When handling the bulb, make sure it is completely cool down
before any direct contact to hands.
⊗When handling globes hold with a cloth or gloves to ensure perspiration does not come in contact with the globe as this can reduce the life of the globe.
---|---

LED LIGHTS:

  • Switch the unit off and pull out the plug first.
  • Wait until the light bulb is cooled down before replacement.
  • Remove the front part with the aid of a screwdriver.
  • Pull out the LED light carefully and replace it with the same type and rated LED light(2*2W LSD-B1 LED light)
  • Replace the front part back to the unit with a screwdriver.
  • ILOCOS D code for this lamp is: DBR-2/65-H-64
    – LED modules, self-ballasted – round lamp
    – Max wattage: 2 W
    – Voltage range: AC 220-240V
    – Dimensions:

neue NGI96NX Cooker Hood figure 20

ENVIRONMENTAL PROTECTION:

| This product is marked with the symbol on the selective sorting of waste electronic equipment. This means that this product must not be disposed of with household waste but must be supported by a system of selective collection in accordance with Directive 2012/19/EU. It will then be recycled or dismantled to minimize impacts on the environment, electrical and electronic products are potentially dangerous for the environment and human health due to the presence of hazardous substances. For more information, please contact your local or regional authorities.
---|---

NOTE:
The following shows how to reduce the total environmental impact (e.g. energy use) of the cooking process).

  1. Install the cooker hood in a proper place where there is efficient ventilation.
  2. Clean the cooker hood regularly so as not to block the airway.
  3. Remember to switch off the cooker hood light after cooking.
  4. Remember to switch off the cooker hood after cooking.

INFORMATION FOR DISMANTLING

Do not dismantle the appliance in a way that is not shown in the user manual. The appliance could not be dismantled by the user. At the end of life, the appliance should not be disposed of with household waste. Check with you Local Authority or retainer for recycling advice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals