silen D-CBX1 Chatbot Telephone Booth Installation Guide
- June 7, 2024
- silen
Table of Contents
D-CBX1 Chatbot Telephone Booth
CHATBOX
Assembly Manual
Product components
IMPORTANT SAFETY INFORMATION
Take photographs before and aer opening the cardboard packages to document any
damage caused during delivery.
Minimum two persons required for the product assembly.
4 x 4 m
Required Assembly Space
DANGER!
Assembly requires approximate 4x4m open floor space for safety.
Risk of p-over during product assembly, addional support required for safety.
2 Person Assembly
30
Approximate assembly me is 30 min.
min
Note! Assembly may take longer.
Approx. Assembly
Time
Tip-Over Hazard!
Don’t support on corner
Risk of damaging the glass panels
or other product parts if support-
ed on corners for assembly and transportaon.
COMPONENTS:
A x1
D x1
E x1
B x1
C x1
F x1
G x1
I x2
1
Aachments and Tools
I
D
B
G
E
TOOLS: F
Allen key set
C
Level
I
Screwdriver
Scissors
k x1 A
ATTACHMENTS:
6x8mm
a x4
b x4
c x4
d x6
e x6
M6x35 Allen 5mm
f x6
M6x45 Allen 5mm
g x6
M6x80 Allen 5mm
h x10
M5x35 Allen 2,5mm
i x1
j x1
M6x35 (Black) Allen 5mm
2
1. Floor module Assembly
A
75 432
372 75
A
445 18
Place the Floor module (A) at desired locaon of the Chatbox. Remove carpet
plugs on marked posions and use a 5mm allen key and a level to adjust all 7
levelling glides.
Note! Glides must be lowered minimally.
475
18
5mm
A
A
3
2. Side module Assembly
2 Person Assembly DANGER!
B
Tip-Over Hazard!
C a x4
A
Ca A
Li the Side modules (B and C) on top of the Floor module (A) and drive in
screws “a” to secure the Side modules.
Note! Assembly must be supported from the side to avoid tipping over before
second Side module is attached.
aC A
a x4
M6x35 Allen 5mm
4
3. Ceiling module Assembly
D
B C
Step 1. b
D C
Step 2. D
B
b x4 2 Person Assembly
Step 1. Li the Ceiling module (D) on top of the Side modules (B and C) and drive in screws “b” to secure the side modules. Step 2. Connect the electrical fings and place the fings into the Ceiling module (D)
D C
b x4
M6x45 Allen 5mm
5
4. Table Assembly
B E
2 Person Assembly
c x4
Step 1.
E B
Step 3. E
B
Step 2. c
B
c x4
M6x80 Allen 5mm
E
Step 1. Li table (E) above the lath aached to side module (B), push the table (E) against the side module (B) and lower the table (E) unl it stands on the lath. Step 2. Drive in screws “c” to secure table (E) to the side module (B). Step 3. Connect the electrical fings between the table (E) and Side module (B).
6
5. Gasket Assembly
k x1
6x8mm
k k k
7
ASSEMBLY OPTIONS FOR CHATBOX HANDEDNESS
RIGHT HANDED ASSEMBLY
LEFT HANDED ASSEMBLY
6L Le Handed Rear Glass assembly @ page 8-9
7L Le Handed Door Frame assembly @ page 10
6R Right Handed Rear Glass assembly @ page 11-12
7R Right Handed Door Frame assembly @ page 13
*6L. Le Handed Rear Glass Assembly
Don’t support on corner
2 Person Assembly
F
d x6
e x6
M5x35 Allen 2,5mm
f x6
g x6
d x6 e x6 f x6 g x6
8
*6L. Le Handed Rear Glass Assembly
d
d
BACK
F
d
d
TABLE
d
Step 1. d
d
Step 2. e
FRONT
Note! Table on Left side
Step 1. Aach part “d” to the shown locaons on side modules (B and C) using a 2,5mm allen key. Note! Leave a gap in the boom of the aachment Step 2. Place sleeve “e” around part “d” Step 3. Li the glass panel (F) on top of previously aached parts. Step 4. Use parts “f” and “g” and a 1,5mm allen key to aach the Rear glass (F) on the Chatbox
Step 3.
Gap! F
Step 4. gf F
B & C
B & C
B & C
B & C
9
7L. Le Handed Door Frame Assembly
G Open
Don’t support on corner
2 Person Assembly
Note! Table on Left side
BACK
TABLE
h x10
Place support under Frame
Drive in screws “h” to aach the Door frame (G) to the Chatbox Note! Door must be in “open” position and supported from bottom edge for assembly.
h G
h G
B&C
B&C
FRONT
h
Gh
Open
h
h
h
h
h
h
10
6R. Right Handed Rear Glass Assembly
Don’t support on corner
2 Person Assembly
F
d x6 e x6 f x6 g x6
d x6
e x6
M5x35 Allen 2,5mm
f x6
g x6
11
6R. Right Handed Rear Glass Assembly
d
d
BACK
F
d
d
TABLE
d
Step 1. d
d
Step 2. e
FRONT
Note! Table on Right side
Step 1. Aach part “d” to the shown locaons on side modules (B and C) using a 2,5mm allen key. Note! Leave a gap in the boom of the aachment Step 2. Place sleeve “e” around part “d” Step 3. Li the glass panel (F) on top of previously aached parts. Step 4. Use parts “f” and “g” and ta 1,5mm allen key to aach the Rear glass (F) on the Chatbox
Step 3.
Gap! F
Step 4. gf
F
B & C
B & C
B & C
B & C
12
7R. Right Handed Door Frame Assembly
G
Open
Don’t support on corner
2 Person Assembly
Note! Table on Right side
BACK
TABLE
Place support under Frame
h x10
Drive in screws “h” to aach the Door frame (G) to the Chatbox Note! Door must be in “open” position and supported from bottom edge for assembly.
h G
h G
B&C
B&C
FRONT
G
h
h
Open
h
h
h
h
h
h
13
8. Door Handle Assembly
G
Open
i
Step1. Place the Door handle “i” on the
Door glass (G) and secure it with the provid-
ed handle set aachments.
i x1
Step 2. Place the second half of the handle on top of the aachments and secure
the
bolts with an allen key.
i
i
G
G
ii
i
14
9. Connecng the eletrical fings
Remove the Cover plate from Ceiling module (D) to expose electrical fings. Connect the Power cord “j” and return Cover plate.
j x1
– Powercord connection – Side panel (table socket) connection
j
15
Optional. Power cord posioning
C
j j
B j 16
10. Covering plate Assembly
I I
- I
Aach the Covering plates (I) by placing them first on top of the Chatbox and
then slowly let the magnets pull the side panel to it’s place.
17
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>