NANROBOT D6+ Scooter User Manual

NANROBOT D6+ Scooter

REQUIRED CHECK BEFORE RIDING

WARNING!
Please read this manual carefully before using the product.

CHECK THE SCOOTER BEFORE RIDING

1. Check that the control panel turns on.
2. Ensure that the brakes are working properly.
3. Check that the brake pads are not damaged or need replacing.
4. Make sure the seat is stable and secure.
5. Check that the horn is operating correctly.
6. Ensure the switch for the Eco and Turbo mode switches are working normally.
7. Make sure the voltage value is within the normal range of 43V-58.8V.
8. Make sure the folding mechanism is in good condition and operational.
9. Prolonged Exposure to UV Rays, Rain, and the Elements May Damage the Enclosure Materials, Store Indoors When Not in Use.
10. WARNING-To reduces the risk of injury, the user must read the instruction manual.
11. WARNING-Risk of Fire and Electric Shock-No User Serviceable Parts.
12. AVERTISSEMENT-Risque d’incendie – Aucune des pieces ne peut etre reparee par l’utilisateur.

Manufacturer: shanghai dualtron intelligent techonology co,.ltd Website:www.nanrobot.com FB: Nanorobot Electric Scooters

SAFETY PRECAUTIONS

1. Always wear a helmet and knee and elbow pads when riding.
2. When first riding the scooter maintain a low speed and slowly increase sped as riding skills improve.
3. Do not ride the scooter on rainy days.
4. Riding through puddles is not recommended.
5. Children under the age of 16 are prohibited from riding.
6. The handlebar should be adjusted to an appropriate and comfortable position.
7. When going downhill, ensure you are driving slowly to avoid accidents.
8. Obey all traffic rules.
9. Ensure all screws are in condition and appropriately fastened.
10. Charging Instructions-Use only with the specified charger in the instructions.
11. The slope of the ridge: <30°.
12. The range of The environment temperature when riding or charging: is 0-40°C.
13. Store in a cool, dry, and ventilated place when not in use.
14. Don’t throw it away arbitrarily when it’s broken.

PRODUCT SPECIFICATIONS

PRODUCT COMPONENTS

NANOROBOT D6+

SAFETY GUIDELINES BEFORE RIDING

CHECK THE FOLLOWING PARTS OF THE PRODUCT AFTER UNBOXING

1. Check if there is a tool kit.
2. Check for a charger.
3. Check if there is a voltage lock key.
4. All nuts and screws should be tight.
5. Seat (if available).
6. Test the brakes.

PACKING LIST

UNBOXING

IMPORTANT CHECKLIST

• Check whether the LCD control panel screws are tightened.
• Make sure the voltage lock and light button screws are tightened.
• Check whether the brake lever screws are tightened.
• Check whether the bracket screws are tightened.

HANDLEBAR ASSEMBLY

1. CD Loosen the screws on the handle mount with a 4mm hex wrench, which is included in the basic tool kit.
2. After aligning the handlebar with the center mount, replace the cover mount, and tighten the fixing bolt.
3. Progressively tighten the bolts in sequential order (1 to 4), ensuring equal tension balance between the mount and handlebar.
4. Installation complete.

SCOOTER UNFOLDING

HANDLEBAR UNFOLDING

1. CD Push the handlebar in the direction of the arrow.
2. Align the ]-shaped buckle with the grooves, then tighten the folding knob.
3. Make sure to perfectly align the ] -shaped buckle.
4. Unfolding complete.

HANDLEBAR FOLDING

1. CD Loosen the knob in the direction of the arrow.
2. Keep loosen ing the folding knob until the] -shaped buckle completely leaves the grooves
3. Lower the handlebar.
4. Folding complete.

CHARGING &RANGE

When charging, connect the charging cable in this order:

1. FIRST to the scooter’s charging port
2. THEN to the power outlet

The Information about the charger

• MODEL: FY1505882000
• INPUT:100-240V~ 50/60Hz Max.3.0A
• OUTPUT:58.8V ………. 2A IP20
• Manufactured By: Shenzhen Fuyuandian Power Co.,Ltd

NOTE: When connected to the charger, the red light indicates that the scooter is charging. The light will turn green when fully charged. Be sure to close the charging port cap when driving or storing except when charging. Use only genuine chargers.

Range: 20-45 miles. The range of the scooter depends on many factors: road conditions (off-road, uphill), weather, rider’s body weight, frequent braking and acceleration, single/dual drive, gears 1 /2/3, etc.

POWER TURN ON/OFF

Insert the key into the power lock and turn it to unlock your scooter.2 Press the POWER key for 3 seconds to turn it on.

You can turn off power either directly via the power lock or turn it off by pressing and holding the POWER key on the control panel for 3 sec.

HANDLEBAR CONTROLS

CONTROL PANEL INSTRUCTIONS

CONTROL PANEL

• POWER: long presses will either start or shut down the scooter)
• MODE: parameter setting key
• Gear: current gear (gears: 1, 2, 3)
• Switch Gears : Pressing the key ( M ) allows you to change gears, shifting from level 1 (slowest) to level 3 (fastest).
• Short press the key ( ) to switch between Single/Dual drives.
• Speed Unit: mile/h, km/h.
• Battery Indicator: current battery capacity.

1. The panel will automatically turn off after three minutes of inactivity.
2. A short press of the POWER key( ) allows the user to change the display content of the instrument (Single Drive, Dual Drive.)
3. Double-click the POWER key( M ) briefly and ODO is displayed, and the total mileage of all trips is shown.
4. A long press of the MODE key( M ) will clear the TRIP mileage (under the TRIP interface).

PARAMETER SETTINGS

Press and hold both the POWER ( )and MODE( M ) keys at the same time to enter the mode settings menu. Short pressing either MODE(+ 1) or POWER (-1) will change parameter items. Once at the desired parameter, holding MODE will change the value to flashing and all for that parameter to be modified. A short press to the POWER key will decrease the value, and a short press on MODE increases the value. After the modification is completed, hold the MODE key down to set and save the value, the flashing will also stop.

Note: Please keep the default values of the parameter settings; please do not change these values.

FOR EXAMPLE

How to disable EBS (Electric Braking System)

Press and hold both the POWER( )and MODE( M ) key simultaneously to enter the settings, and short press MODE (or POWER) until P9 is displayed. Then hold MODE to select P9, short press POWER or MODE to change it to 0. Then long press MODE to save the changes.

PARAMETER SETTINGS

COMMON ISSUES AND SOLUTIONS

• Issue 1: Both the headlight and horn are not working. This happens when the headlight is defective and is solved by replacing the headlight.
• Issue 2: The scooter is not charging. The issue may be with the charging port. If the charging port is burned out, it will require replacing. The other may be that the charger is damaged. In either case, please contact customer service via e-mail to receive a solution.
• Issue 3: The brake pads produce abnormal sounds. Generally,  this is due to malposition. Please use the tool kit and adjust to the correct place.

MAINTENANCE & FAQ

The screws should be regularly maintained, inspected, and tightened. Especially the screws on the folding mechanism, brake system, and motors (axle nuts).

1. Tighten the folding mechanism screws, handlebar, front & rear shock absorbers, and front & rear wheel axle nuts.
2. Brakes: if you find rust or excessive wear on the brakes, which will occur with regular use over time, the brake pads and brake dies should be replaced.
3. Motor: Check the motor wires regularly. All exposed wires should be wrapped with electrical tape.
4. Tires:
5. Do not inflate the tires beyond the recommended air pressure range.
6. The tires will slide easily in wet conditions. Avoid rain, snow, icy road, wet dirt road, water, and poor visibility.
7. Replace the tires on your scooter once wear patterns become evident. This will prolong the use of the scooter.
8. Speed limit removal: please go to P8 and then press the ”M” button for 1 minute until your go back to the main menu.
9. Battery & overheat protection: the controllers and the battery has temperature sensors and the scooter stops working when it gets too hot. Please wait about 0.5-2 hours to cool down the scooter or use eco/1 st gear to continue riding after 5-10 minutes.

CUSTOMER SUPPORT

Scooters manufactured by Nanorobot are pre-assembled, though some of the parts may require assembly by our customers. To help ensure the safety of your scooter and driving, please check and test everything before using your scooter. If your inspection finds an issue with the scooter, please contact your seller. You can also contact your seller if you need assistance with any of the assembly

SHIPPING

To avoid damage during transport, we have safely packed all of the electric scooter components in foam and cardboard. If there is something broken upon arrival, please take photos of the damaged parts and contact the seller, they will be able to offer you a solution.

MECHANICAL DAMAGE OR MODIFICATIONS
If your scooter is damaged due to an accident or misuse, you can buy replacement parts from nanrobot.com, the distributor or seller you made your purchase from, or you can send the scoot­er to be repaired. The buyer bears all repair costs. If there are other after-sale problems or questions, please send an e-mail to us at support@nanrobot.com.

WARRANTY GUARANTEE

We do provide a warranty and offer customer service for our products if you find there is a quality issue. You can do this by contacting us, and we will offer professional instructions and solutions timely. For the entire scooter, vulnerable parts like tires, brake discs, horns, dash board, light, etc. are within the warranty of 90 days Battery and controllers are within the range of 180 days. The frame is within 365 days repair warranty. If the problem is caused by non-human factors, we will provide new replacements for free. We are not responsible for wrong returns and refund loss, the buyer should be responsible for more than 20% return charge, and double-way transportation charge.

EXCHANGES (IF APPLICABLE)
We only replace items if they are defective or damaged. We do not accept returns but do offer exchanges; all inquiries can be directed to us via e-mail at support@nanrobot.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>