NANROBOT LS7 Electric Scooter User Manual

NANROBOT LS7 Electric Scooter User Manual

www.nanrobot.com
Support@nanrobot.com

Website : www.nanrobot.com
FB : Nanrobot Electric Scooters

Required Check Before Riding

1. Check that the control panel turns on.
2. Ensure that the brakes are working properly.
3. Check that the brake pads are not damaged or need replacing.
4. Make sure the seat is stable and secure.
5. Check that the horn is operating correctly.
6. Ensure the switch for Eco and Turbo mode switch are working normally.
7. Make sure the voltage value is within the normal range of 43V-58.8V.
8. Make sure the folding mechanism is in good condition and operational.
9. Prolonged Exposure to UV Rays, Rain and the Elements May Damage the Enclosure Materials, Store Indoors When Not in Use.
10. WARNING-To reduce the risk of injury, user must read instruction manual.
11. WARNING-Risk of Fire and Electric Shock-No User Serviceable Parts.

Safety Guidelines

Safety Precautions

1. Always wear a helmet and knee and elbow pads when riding.
2. When first riding the scooter maintain a low speed and slowly increase sped as riding skills improve.
3. Do not ride the scooter on rainy days.
4. Riding through puddles is not recommended.
5. Children under the age of 16 are prohibited from riding.
6. The handlebar should be adjusted to an appropriate and comfortable position.
7. When going downhill, ensure you are driving slowly to avoid accidents.
8. Obey all traffic rules.
9. Ensure all screws are in condition and appropriately fastened.
10. Charging Instructions-Use only with specified charger in instruction.
11. The slope of riding: <30°.
12. The range of The environment temperature when riding or charging: 0-40°C.
13. Store in a cool, dry and ventilated place when not in use.
14. Don’t throw it away arbitrarily when it’s break.

Product Specifications

Products Components

NANROBOT LS7+

Safety Guidelines Before Riding

CHECK THE FOLLOWING PARTS OF THE PRODUCT AFTER UNBOXING

1. Check if there is a tool kit.
2. Check for a charger.
3. Check if there is a voltage lock key.
4. All nuts and screws should be tight.
5. Seat (if available).
6. Test the brakes.

PACKING LIST

Unboxing

IMPORTANT CHECKLIST

HANDLEBAR ASSEMBLY

DAMPER ASSEMBLY

Scooter Unfolding

HANDLEBAR UNFOLDING

HANDLEBAR FOLDING

Charging & Range

When charging, connect the charging cable in this order:

1. FIRST to scooter’s charging port
2. THEN to the power outlet

NOTE: When connected to the charger, the red light indicates that the scooter is charging. The light will turn green when fully charged.

Be sure to close the charging port cap when driving or storing except when charging. Use only genuine chargers.

Range: 31-37 miles. The range of the scooter depends on many factors: road conditions (off-road, uphill), weather, rider’s bodyweight, frequent braking and acceleration, single/dual drive, gears 1 /2/3 etc.

Power Turn On/Off

(1) Insert the key into the power lock and turn to unlock your scooter.
(2) Press the POWER key for 3 seconds to turn on.

You can turn off power either directly via the power lock or turn it off by pressing and holding the POWER key on the control panel for 3 sec.

HANDLEBAR CONTROLS

CONTROL PANEL INSTRUCTIONS

CONTROL PANEL

Parameter Settings

COMMON ISSUES AND SOLUTIONS

Issue 1: Both the headlight and horn are not working. This happens when the headlight is defective and is solved by replacing the headlight.

Issue 2: The scooter is not charging. The issue may be with the charging port. If the charging port is burned out, it will require replacing. The other may be that the charger is damaged. In either case, please contact customer service via e-mail to receive a solution.

Issue 3: The brake pads produce abnormal sounds. Generally, this is due to malposition. Please use the tool kit and adjust to the correct place.

Remote Control For Light

Maintenance & FAQ

The screws should be regularly maintained, inspected and tightened. Especially the screws on the folding mechanism, brake system and motors (axle nuts).

1. Tighten the folding mechanism screws, handlebar, front & rear shock absorbers, front & rear wheel axle nuts.
2. Brakes: if you find rust or excessive wear on the brakes, which will occur with regular use over time, the brake pads and brake dies should be replaced.
3. Motor: Check the motor wires regularly. All exposed wires should be wrapped with electrical tape.
4. Tires:
5. Do not inflate the tires beyond the recommended air pressure range.
6. The tires will slide easily in wet conditions. Avoid rain, snow, icy road, wet dirt road, water, poor visibility.
7. Replace the tires on your scooter once wear patterns become evident. This will prolong the use of the scooter.
8. Speed limit removal: please go to P8 and then press the ”M” button for 1 minute until your go back to the main menu.
9. Battery & overheat protection: the controllers and the battery has temperature sensors and the scooter stops working when it gets too hot. Please wait about 0.5-2 hours to cool down the scooter or use eco/1st gear to continue riding after 5-10 minutes.

Customer Support

Scooters manufactured by Nanrobot are pre-assembled, though some of the parts may require assembly by our customers. To help ensure the safety of your scooter and driving, please check and test everything before using your scooter. If your inspection finds an issue with the scooter, please contact your seller. You can also contact your seller if you need assistance with any of the assembly

SHIPPING

To avoid damage during transport, the we have safely packed all of the electric scooter components in foam and cardboard. If there is something broken upon arrival, please take photos of the damaged parts and contact the seller, they will be able to offer you a solution.

MECHANICAL DAMAGE OR MODIFICATIONS

If your scooter is damaged due to an accident or misuse, you can buy replacement parts nanrobot.com, the distributor or seller you made your purchase from, or you can send the scooter to be repaired. The buyer bears all repair costs. If there are other after-sale problems or questions, please send an e-mail to us at support@nanrobot.com.

Warranty & Guarantee

Warranty Guarantee

We do provide a warranty and offer customer service for our products if you find there is a quality issue. You can do this by contacting us, and we will offer professional instructions and solutions timely.

For the entire scooter, vulnerable parts like tires, brake discs, horn, dash board, light etc. are within the warranty of 90 days Battery and controllers are within the range of 180 days. The frame is within 365 days repair warranty. If the problem is caused by non-human factors, we will provide new replacements for free.

We are not responsible for wrong return and refund loss, the buyer should be responsible for more than 20% return charge, and double-way transportation charge.

Exchanges (If Available)

We only replace items if they are defective or damaged. We do not accept returns but do offer exchanges; all inquiries can be directed to us via an e-mail at support@nanrobot.com.

References

• NANROBOT OFFICIAL SITE | Electric Scooter | High Speed & Duration
• NANROBOT OFFICIAL SITE | Electric Scooter | High Speed & Duration

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>