Dual XRM59BT Owner’s Manual
- June 6, 2024
- Dual
Table of Contents
Dual XRM59BT
INSTALLATION
Preparation
Please read entire manual before installation.
Before You Start
- Disconnect negative battery terminal. Consult a qualified technician for instructions.
- Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Step 1:
Step 2:
Step 3:
Step 4:
Remove the plastic caps and use the removal keys to remove the unit.
Wiring Diagram
OPERATION
Control Locations
- Power
- Mute
- Voice Control
- Volume Knob
- Bluetooth Talk
- USB Port
- Auxiliary Input
- Reset
- Preset 6 / Folder Up
- Preset 5 / Folder Down
- Preset 4 / Random
- Preset 3 / Repeat
- Preset 2 / Intro
- Preset 1 / Play/Pause
- Mode
- Band/Display
- Tune Up
- Tune Down
General Operation
Power On/Off: Press the button to turn the unit on. Press again to turn
the unit off.
Changing Modes: Press MODE to select between Radio, USB, Bluetooth, AUX.
Modes of operation are shown in the display.
Volume: Adjust volume using the volume knob (00-40).
Auxiliary Inputs: Insert a 3.5mm cable in the unit’s front AUX port.
Reset: Press the RESET button to reset the unit back to the factory
settings if abnormal operation occurs. The reset button is located on the
front panel.
Setting the Clock: With the unit on, long press DISP to display clock
time. Press and hold DISP until the hours or minutes begin to flash, then
release. Rotate the volume knob to adjust the time. Long press DISP to finish
the clock setting.
Display: Press DISP to toggle display between various displayed
information.
Audio / Menu:
- Press the volume knob momentarily to select between audio functions.
- Press and hold the volume knob for more than two seconds to select between the menu functions.
- Rotate the volume knob left/right to adjust or activate the desired function/audio.
AM/FM Tuner Operation
Seek Tuning: Press TUNE or TUNE to seek to the previous or next strong
station.
Manual Tuning: Press and hold TUNE or TUNE to enter manual tuning mode,
then press TUNE momentarily to change radio frequency up or down one step at a
time. Press and hold TUNE
Band: Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands. Up
to six presets can be programmed for each band, enabling up to 18 FM stations
and 12 AM stations to be stored in memory.
Storing Presets: Up to 18 FM and 12 AM stations can be stored. To store a
station, select the desired band and station. Press and hold the desired
preset button (1-6) for more than two seconds. When stored, the preset number
will appear in the display.
Recalling Presets: Preset stations can be recalled any time by pressing
the corresponding preset button.
Automatically Store: Press and hold MENU for more than 2 seconds, then
press DISP to store 18 FM stations and 12 AM stations automatically.
Preset Scan Stations: Touch PS to recall each preset station that has
been stored in memory for each band. (Available with the Dual Smart Remote App
only)
Dual iPlug P2 Smart App Remote Control
Use the Dual iPlug P2 Smart App Remote Control on an Apple or Android
smartphone to control the receiver via Bluetooth.
Change the mode, station, song, volume, and settings directly from your
smartphone without being in the receiver’s line-of-sight.
Download the Dual iPlug P2 Smart App Remote Control from Apple App Store or
Google Play Store and install it on your smartphone or tablet (QR code
download link on the right).
Voice Activation
Your receiver is designed with an easy access voice activation button to use
Siri® or the Google Assistant™ via your car’s Bluetooth. Interact with your
smartphone assistant while you drive with only the push of a button!
Bluetooth should be paired between your smartphone and the receiver. Press the
voice activation button , and the receiver will switch into Bluetooth mode,
This will activate Siri® or Google AssistantTM on your smartphone. You will
need to manually switch back to the previous or desired mode once this
operation is terminated.
Front 3.5mm Aux Input
Connect an optional audio source into the 3.5mm (front panel) input. Select auxiliary input from the Main Menu to listen to audio. Adjust volume on the external audio source as needed (if connected to the headphone output of the device).
Troubleshooting
| Problem | Cause | Action |
|---|
Unit will not turn on (no power)
| Yellow wire not connected or incorrect voltage Red wire not connected or
incorrect voltage| Check connections for proper voltage (11~16VDC)
Black wire not connected| Check connection to ground
Fuse blown| Replace fuse
Unit has power (but no sound)| Speaker wires not connected| Check
connections at speakers
One or more speaker wires touching each other or touching chassis ground|
Insulate all bare speaker wires from each other and chassis ground
Unit blows fuses| Yellow or red wire touching chassis ground| Check for
pinched wire
Speaker wires touching chassis ground| Check for pinched wire
Incorrect fuse rating| Use fuse with correct rating
NO FILE appears on display| No playable MP3 files found on the
device| Check the device for valid MP3 files
NO SUPPORT appears on display| An invalid ID3 tag version is present|
Version 1.0 to 2.0 ID3 tags are supported.
Limited One Year Warranty
This warranty gives you specific legal rights. You may also have other rights
which vary from state to state.
Dual Electronics Corp. warrants this product to the original purchaser to be
free from defects in material and workmanship for a period of one year from
the date of the original purchase.
Dual Electronics Corp. agrees, at our option, during the warranty period, to
repair any defect in material or workmanship or to furnish an equally new,
renewed or comparable product (whichever is deemed necessary) in exchange
without charges, subject to verification of the defect or malfunction and
proof of the date of purchase. Subsequent replacement products are warranted
for the balance of the original warranty period.
Who is covered? This warranty is extended to the original retail
purchaser for products purchased from an authorized Dual dealer and used in
the U.S.A.
What is covered? This warranty covers all defects in material and
workmanship in this product. The following are not covered: software,
installation/removal costs, damage resulting from accident, misuse, abuse,
neglect, product modification, improper installation, incorrect line voltage,
unauthorized repair or failure to follow instructions supplied with the
product, or damage occurring during return shipment of the product. Specific
license conditions and copyright notices for the software can be found via
www.dualav.com.
What to do?
1. Before you call for service, check the troubleshooting guide in your
owner’s manual. A slight adjustment of any custom controls may save you a
service call.
2. If you require service during the warranty period, you must carefully pack
the product (preferably in the original package) and ship it by prepaid
transportation with a copy of the original receipt from the retailer to an
authorized service center.
3. Please describe your problem in writing and include your name, a return
UPS shipping address (P.O. Box not acceptable), and a daytime phone number
with your shipment.
4. For more information and for the location of the nearest authorized
service center please contact us by one of the following methods:
• Call us toll-free at 1-866-382-5476
• E-mail us at cs@dualav.com
Exclusion of Certain Damages: This warranty is exclusive and in lieu of any and all other warranties, expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company’s negligence, actual or imputed. No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental or consequential damages.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Dual Electronics Corp.
Toll Free: 1-866-382-5476
www.dualav.com
©2020 Dual Electronics Corp. All rights reserved.
Other trademarks and trade names are those of their respective owners.
NSA0120-V01
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>