GRUNDIG MC 9030 Hair and Beard Clipper User Manual

GRUNDIG MC 9030 Hair and Beard Clipper

Please read this manual first!

Dear Customer,
Thank you for purchasing a Grun-dig product. We hope that you get the best results from your product which has been manufactured with high quality and state-of-the-art technology. Therefore, please read this entire user manual and all other accompanying docu-ments carefully before using the product and keep it as a reference for future use. If you handover the product to someone else, give the user manual as well. Follow all warnings and information in the user manual.

Meanings of the symbols

The following symbols are used in various sections of this manual:

• Important information and useful hints about usage.
• WARNING: Warnings against dangerous situations concerning the security of life and property.
• Electrical insulation class.

Important safety and environmental instructions

Please read this instruction manual thoroughly prior to using this appliance! Follow all safety instructions in order to avoid damage due to improper use!
Failure to follow these instructions voids any granted warranty.

General safety

• The appliance is designed for domestic use only.

• This appliance is designed solely for trimming human hair and beards. Any other use is expressly prohibited.

• Suitable for use in a bath or shower.

• Suitable for cleaning under an open water tap.

• Never use the appliance if it, the cutting head or the power adapter show any signs of damage. Contact authorized service.

• Only use the appliance with the parts and power adapter supplied.

• Caution! Always keep the appliance and power adaptor dry.

• When the appliance is being charged, on no ac-count should it come into contact with water or any other liquid.

• After charging, always unplug the cable from the socket and disconnect the power adapter from the wall socket.

• Do not drop the appliance.

• Charging adaptor and power cable cannot be repaired once damaged. Please make sure that you dispose the charging adaptor in accordance with environmental directions. You can get your new charger from the manufacturer or authorised service provider.

• Never place the appliance, accessories or power adapter on or near hot surfaces.

• Check that the mains voltage on the rating label corresponds to your local mains supply.

• Keep the appliance out of the reach of children.

• Before cleaning or user maintenance operation first plug out.

• This appliance can be used by children aged from 8 years and above and persons with re-duced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction con-cerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children with-out supervision.

• Do not open the appliance under any circumstances. No warranty claims are accepted for damage caused by improper handling.
  This appliance contains batteries that are non-replaceable.
  WARNING: For the purposes of recharging the battery, only use the detachable supply unit pro-vided with this appliance.
  WARNING: Detach the hand-held part from the supply cord before cleaning it in water.
  WARNING: Adaptor and charging base cannot fall in water.

• Do not squeeze or bend the power cord and do not rub in on sharp edges in order to prevent any damage. Keep the cord away from hot sur faces and open flames.

• If you keep the packaging materials, keep them out of the reach of children.

• This appliance is designed solely for trimming human hair and beards. Any other use is ex-pressly prohibited.

• Before removing the battery, the product should be disconnected from the electricity supply. Ob-serve the local legislation and regulations when disposing of the battery.

Compliance with the WEEE Directive and Disposing of the Waste Product:
This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).

This symbol indicates that this product shall not be disposed with other household wastes at the end of its service life. Used device must be returned to offical collection point for recycling of electrical and electronic devices. To find these collection systems please contact to your local authorities or retailer where the product was puchased. Each household performs im-portant role in recovering and recycling of old appliance. Appropriate disposal of used appliance helps prevent potential negative conse- quences for the environment and human health.

Compliance with RoHS Directive

The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.

Package information

Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

Information on Waste Batteries

This symbol on rechargeable batteries/batteries or on the packaging indicates that the rechargeable battery/battery may not be disposed of with regular household waste. Always dispose of used rechargeable batteries/batteries in accordance with local environmental regulations. Make inquiries about the applicable disposal regulations where you live.

Overview

Controls and parts
See the illustrations on page 3.

1. Cutting head

2. High speed setting button (Turbo)

3.  On/Off switch

4. LCD Display

5.  Body

6. Charging dock
   Accessories

7. 3-15 mm comb

8. 18-30 mm comb

9. 33-45 mm comb

Other Accessories
Power adapter Charging plug Cleaning brush Oil

Technical data

• Operating temperature: +5ËšC – +40ËšC
• Storage temperature: 0ËšC -+40ËšC
• Parameter of External Power Supply
• Manufacturer: E-TEK Electronics Manufactory CO., LTD
• Model Identifier: ZD006M050100EU
• Input Voltage: 100-240V~
• Input Frequency: 50/60Hz
• Input Current: 0.3A
• Output Voltage: 5.0V DC
• Output Current: 1.0A
• Output Power: 5.0W
• Average active efficiency: 77.74%
• Efficiency at low load(10%): 73.15%
• No-load power consumption: 0.042W
• Protection class:
• Hair clipper IPX7
• Adaptor IPX4
• Batteries: Li-ion (Lithium-ion rechargeable battery)
• Electrical insulation class: II Design and specifications subject to change without notice.

Power supply

Operating with the power adapter
Check that the voltage indicated on the rating plate of the power adapter corresponds to your local power supply. The only way to disconnect the ap- pliance from the power supply is to unplug the power adapter.

1. Plug the charging plug into the appliance socket and the power adapter into the wall socket.
   • LED battery symbol will start flashing, when the batteries are charged. Once the clipper is completely charged, LED battery symbol will illuminate continually.
   • Charging time:1.5 hours when the bat-tery is fully charged
2. LED battery symbol will start flashing when the unit reaches low battery capacity during operation.
   • When the batteries are discharged: LED battery symbol will not display.
   • Discharge the ap-pliance through normal use. Then recharge to full ca-pacity. Maximum battery capacity will only be reached af-ter several charging/discharging cycles.
   • The adapter and unit may become warm while charging; this is normal operation.
   • When the appliance is fully charged, it has a cordless op-erating time of up to 120 minutes.
   • CAUTION! Please do not operate the unit connected to the power adapter for a long time oth-erwise it may burn out the adapter.
   • Unplug the adapter from the wall when not in use.
   • CAUTION! When in the bathroom or beside a water con-nection, only use the appliance in battery mode; never run it from the mains.
   • The appliance does not run from the mains when the bat-tery is empty. Make sure the appliance is switched off during charging.

Optimising the lifetime of the rechargeable battery

CAUTION!

• Do not leave the switch adapter plugged into the wall socket for more than 24 hours.
• Discharge the bat-tery completely twice a year by let-ting the motor run until it stops. Then fully recharge the battery.
• Please do not operate for long time, or it may burn the adapter.

Preparation

• The trimming length without combing system is 1.5 mm.
• Trimming without a comb is perfect for designer stubble.
• Width of cutting head is 42 mm.

Setting the trimming length
The Adjustable comb allows the appliance to adjust in 15 different lengths:

• Comb 1: 3 mm
• Comb 1: 6 mm
• Comb 1: 9 mm
• Comb 1: 12 mm
• Comb 1: 15 mm
• Comb 2: 18 mm
• Comb 2: 21 mm
• Comb 2: 24 mm
• Comb 2: 27 mm
• Comb 2: 30 mm
• Comb 3: 33 mm
• Comb 3: 36 mm
• Comb 3: 39 mm
• Comb 3:42 mm
• Comb 3: 45 mm

Operation

Before Using, remove the plug of adapter from the mains power socket and remove the connect wire from body . We recommend to trim a small area first to familiarize yourself with the attachment comb.
Hair trimming
Make sure that the hair is clean and completely dry. Place a towel around the neck and shoulders of the person whose hair you are trimming. Make sure that the person is seated so that their head is roughly at your eye level. Before trimming, comb the hair so that it falls naturally and you can see the direction in which it grows.

1. Place the cutting head (1) on the person’s hair. Hold the clipper against the hair, the teeth of the clipper guide pointing upwards yet flat against the head.
2. Move the cutting head (1) against the direction of hair growth. Apply only a slight pressure when cutting with slow, gentle movements.

Useful tips

• Move the clipper upwards and out wards through the hair, a little at a time, against the direc-tion of hair growth.
  The appliance will work most efficiently when cutting through the hair at its own speed. Never force the clipper through the hair. Never switch the clipper off whilst in the hair.
  For longer hair on top of the head, hold the hair between the fingers and cut to the desired length. Always work from the front to the back of the head.

• As you cut, take a break at reg-ular intervals. You can always make a correction, but not once the hair has been cut.

• Only cut a small amount the first time you use it. This is the only way to get used to the variable positions.

• Keep combing the hair. Only look for hair which is too long and comb out clippings.

Beard trimming

1. Place the cutting head (1) on the beard.
2. Move the cutting head (1) against the direction of hair growth. Apply only a slight pressure when cutting with slow, gentle movements.

Useful tips

• The combs are designed for easy removal of excess hair and clean the cutting head (1) with the brush supplied. Clean the appliance as described in the “Cleaning and Care” section.
• For trimming contours, remove the detachable blade. Use the appliance without the combs (cutting length is 1.5 mm).

High speed setting button (2) (Turbo)
Device performance can be maxi-mized by pushing the turbo button (2).

The usage of the BeardCare sensor

The BeardCare sensor detects in real time the density of the beard hair and adjusts the power of the motor accordingly. At Turbo Mode, the BeardCare sensor will be inac-tive.

Information

The appliance must be cleaned regularly so that you can continue to enjoy its top performance and optimum result.

Cleaning and care

Before cleaning, remove the plug of adapter from the mains power socket and remove the connect wire from body.

• Never used liquids to clean the appliance. Use the cleaning brush provided and water only.
• Remove any clip-pings after each use.
• The cutting head of your appliance does not normally need to be oiled. If you want to maintain the original condition of the cutting head for as long as possible, it is worth oiling it at regular intervals (with the oil provided).

Using exclusively the cleaning brush, remove the hairs from the blade head. The blade head may be cleaned with water or other liquids. If in regular use, the blade head should be oiled. For this, use the supplied blade oil.

Storage

• If you do not plan to use the ap-pliance for a long period of time, please store it carefully.
• Make sure that it is unplugged and is completely dry.
• Store the appliance in a cool, dry place.
• Make sure that the appliance is kept out of the reach of children.

References

• Grundig Global
• Service
• SERBÄ°S
• Grundig Türkiye (@grundigturkiye) • Instagram photos and videos

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>