CHAMPION 100740 Amp Parallel Kit User Manual
- June 6, 2024
- Champion
Table of Contents
OPERATOR’S MANUAL
MODEL #100740
PARALLEL KiT
at
or visit championpowerequipment.com
SAVE THESE iNSTRUCTiONS. This manual contains important safety
precautions which should be read and understood before operating the product.
Failure to do so could result in serious injury. This manual should remain
with the product.
Specifications, descriptions, and illustrations in this manual are as accurate
as known at the time of publication but are subject to change without notice.
REV 20210309 Champion Power Equipment, Inc., Santa Fe Springs, CA the USA
| CARBON
MONOXIDE SAFETY: THE BIG PICTURE
As the only safe way to use a portable generator, taking your generator
outside is absolutely mandatory to keep your family safe from carbon monoxide.
But there’s, even more, you can do. By educating yourself about all carbon
monoxide risks, you’ll be better prepared to protect your family from this
colorless, odorless threat.
---|---
|
---|---
www.TakeYourGeneratorOutside.com
INTRODUCTION
Congratulations on your purchase of a Champion Power Equipment(CPE) product.
CPE designs build and support all of our products to strict specifications and
guidelines. With proper product knowledge, safe use, and regular maintenance,
this product should bring years of satisfying service. Every effort has been
made to ensure the accuracy and completeness of the information in this manual
at the time of publication, and we reserve the right to change, alter and/or
improve the product and this document at any time without prior notice.
CPE highly values how our products are designed, manufactured operated, and
serviced as well as providing safety to the operator and those around the
generator. Therefore, it is IMPORTANT to review this product manual and other
product materials thoroughly and be fully aware and knowledgeable of the
assembly, operation dangers, and maintenance of the product before use. Fully
familiarize yourself, and make sure others who plan on operating the product
fully familiarize themselves too, with the proper safety and operating
procedures before each use. Please always exercise common sense and always err
on the side of caution when operating the product to ensure no accident,
property damage, or injury occurs. We want you to continue to use and be
satisfied with your CPE product for years to come.
When contacting CPE about parts and/or services, you will need to supply the
complete model and serial numbers of your product.
Transcribe the information found on your product’s nameplate label to the
table below.
CPE TECHNICAL SUPPORT TEAM
1-877-338-0999
MODEL NUMBER
100740
SERIAL NUMBER
DATE OF PURCHASE
PURCHASE LOCATION
SAfETY DEfiNiTiONS
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
DANGER
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNiNG
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTiON
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
NOTiCE
NOTICE indicates information considered important, but not hazard-related
(e.g., messages relating to property damage).
IMPORTANT SAfETY iNSTRUCTiONS
WARNiNG
Cancer and Reproductive Harm –
www.P65Warnings.ca.gov
DANGER
Generator exhaust contains carbon monoxide, a colorless, odorless, poisonous gas. Breathing carbon monoxide will cause nausea, dizziness, fainting, or death. If you start to feel dizzy or weak, get to fresh air immediately.
OPERATE GENERATOR OUTDOORS ONLY IN A WELL-VENTILATED AREA AND POINT EXHAUST
AWAY.
DO NOT operate the generator inside any building, including garages,
basements, crawlspaces and sheds, enclosure or compartment, including the
generator compartment of a recreational vehicle.
DO NOT allow exhaust fumes to enter a confined area through windows,
doors, vents, or other openings.
DANGER
Using a generator indoors CAN KILL YOU IN MINUTES. Generator exhaust
contains carbon monoxide. This is a poison you cannot see or smell.
NEVER use inside a home or garage, EVEN IF doors and windows are
open.
ONLY use OUTSIDE and far away from windows, doors, and vents.
WARNiNG
Although the generator contains a spark arrester, maintain a minimum distance
of 5 ft. (1.5 m) from dry vegetation to prevent fires.
DANGER
Operate equipment with guards in place. Rotating parts can entangle hands,
feet, hair, clothing, and/or accessories. Traumatic amputation or severe
laceration can result.
Keep hands and feet away from rotating parts. Tie up long hair and remove
jewelry.
DO NOT wear loose-fitting clothing, dangling drawstrings, or items that
could become caught.
DANGER
Generator produces powerful voltage.
DO NOT touch bare wires or receptacles.
DO NOT use electrical cords that are worn, damaged, or frayed. Use only
Champion electrical cords for proper application.
DO NOT operate generator in wet weather.
DO NOT allow children or unqualified persons to operate or service the
generator.
Use a ground fault circuit interrupter (GFCI) in damp areas and areas
containing conductive material such as metal decking.
Connection to your home’s electrical system requires a listed 30A transfer
switch installed by a licensed electrician and approved by the local authority
having jurisdiction. The connection must isolate the generator from the
utility power and must comply with all applicable laws and electrical codes.
WARNiNG
Do not use generators for medical and life support uses. In case of emergency,
call 911 immediately.
NEVER use this product to power life support devices or life support
appliances.
NEVER use this product to power medical devices or medical appliances.
Inform your electricity provider immediately if you or anyone in your
household depends on electrical equipment to live. Inform your electrical
provider immediately if a loss of power would cause you or anyone in your
household to experience a medical emergency.
**WARNiNG
Spark from removed spark plug wire can result in fire or electrical shock.
When servicing the generator:
Disconnect the spark plug wire and place it where it cannot contact the plug
or any other metal object.
DO NOT check for spark with the plug removed. Use only approved spark
plug testers.
WARNiNG
Running engines produce heat. Severe burns can occur on contact. Combustible
material can catch fire on contact.
DO NOT touch hot surfaces. Avoid contact with hot exhaust gases.
Allow equipment to cool before touching.
Maintain at least 3 ft. (91.4 cm) of clearance on all sides to ensure adequate
cooling.
Maintain at least 5 ft. (1.5 m) of clearance from combustible materials.
WARNiNG
Rapid retraction of the recoil cord will pull hand and arm towards the engine
faster than you can let go. Broken bones, fractures, bruises, or sprains could
result. Unintentional
startup can result in entanglement, traumatic amputation, or laceration.
When starting engine, pull the recoil cord slowly until resistance is felt and
then pull rapidly to avoid kickback.
DO NOT** start or stop the engine with electrical devices plugged in and
turned on.
CAUTiON
Exceeding the generator’s running capacity can damage the generator and/or
electrical devices connected to it.
DO NOT overload the generator.
DO NOT tamper with the governed speed.
DO NOT modify the generator in any way.
Safety Symbols
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product.
SYMBOL|
MEANING
---|---
| Read Operator’s Manual. To reduce the risk of injury, users must read
and understand the operator’s manual before using this product.
| Electric Shock. Failure to use in dry conditions and to observe safe
practices can result in electric shock. Improper connections to a building can
allow current to back feed into utility lines, creating an electrocution
hazard. A transfer switch must be used when connecting to a building.
| Fire/Explosion. Fuel and its vapors are extremely flammable and
explosive. Fire or explosion can cause severe burns or death. Keep generator
at least 5 feet (1.5m) from all objects to prevent combustion.
| Hot Surface. To reduce the risk of injury or damage, avoid contact with
any hot surface.
| Open Flame Alert. Fuel and its vapors are extremely flammable and
explosive. Keep fuel away from smoking, open flames, sparks, pilot lights,
heat, and other ignition sources.
| Wet Conditions Alert. Do not expose to rain or use in damp locations.
CONTROLS AND FEATURES
Read this operator’s manual before operating your Parallel Kit. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference.
Control Panel
- Power Indicator – Illuminates green when power is being supplied to the parallel kit.
- Circuit Breakers (Push Reset) – Protects the generator against electrical overloads.
RECEPTACLES
A| | 120V AC, 30A RV (NEMA TT-30R)
May be used to supplying electrical power for operation of 120 Volt AC, 30
Amp, single phase, 60 Hz electrical loads.
B| | 120V AC, 30A Locking (NEMA L5-30R)
May be used to supplying electrical power for operation of 120 Volt AC, 30
Amp, single phase, 60 Hz electrical loads.
ASSEMBLY AND OPERATiON
This parallel kit is intended for use with Champion Power Equipment inverters
rated between 2000 and 3000 starting watts. Please refer to your inverter
Operator’s Manuals for safety rules, start-up and shut down procedures,
specifications, and troubleshooting.
The total output of this kit will depend on the rated wattage of the inverters
connected to it. The maximum output of the parallel kit is the amperage rating
of the circuit breakers.
Paralleling Two inverters
WARNiNG
If not spaced apart, the exhaust heat from one unit may discolor or melt the
plastic on the other unit. Always read your inverter Operator’s Manuals before
operating the inverters and parallel kit.
-
Ensure both inverters are turned off and all electrical loads are disconnected before installing a parallel kit.
-
Align the inverters in a “V” configuration so the exhausts of each inverter are pointed well away from each other and the inverters are a minimum of 18 in. (46 cm) apart.
-
Mount the parallel kit to the inverter on the right of the “V” so that it rests on the side without the fuel cap.
-
Place the bracket around the handle and tighten the fastening dial by turning clockwise until snug. Do not overtighten. You may need to loosen the fastening dial to get it around the handle before tightening.
-
On each inverter, lift the parallel port covers, if applicable, and insert the RED power lead into the RED receptacle and the BLACK power lead into the BLACK receptacle.
-
On each inverter, connect the grounding wire to the grounding terminal on the inverter and secure the grounding lugs.
-
Start engine of both inverters according to inverter Operator’s Manuals. Observe the green output indicator light on both inverter panels. The light may blink during start-up and will turn solid green when loads may be connected.
-
Connect devices to the parallel kit and/or inverters up to the receptacle-rated amperage. It is best to connect devices with the largest load first. Allow the engine to stabilize before plugging in more devices. Never exceed the specified capacity of the receptacle.
-
Follow the instructions in the inverter Operator’s Manuals when turning off the inverters.
NOTiCE
If the parallel kit has been overloaded and the circuit breaker has been
tripped, reduce the load and press the parallel kit reset button to restore
power.
NOTiCE
This parallel kit is meant to parallel two ParaLINK compatible inverters
together. Both inverters must have ParaLINK parallel receptacles as shown
below:
NOTiCE
This unit should NOT be used to connect inverters with non-ParaLINK
receptacles such as the style shown below:
Adjusting the Anti-Vibration Wedges
There are two rubber wedges on the bottom of the parallel kit that can be
removed or moved to create a friction fit wedge between the parallel kit and
inverter. If, after tightening the fastener dial,
your parallel kit is vibrating during operation slide the wedges toward the
back of the parallel kit until snug to reduce vibration.
CABLE STORAGE
When not in use, neatly wrap the cables and use the spring-loaded clips on top
of the parallel kit to hold the cables in place.
SPECIFICATIONS
Specifications
Model ………………………………………………. 100740
Volts AC …………………………………………………. 120
Frequency ……………………………………………..60 Hz
Phase ………………………………………………… Single
Weight ………………………………………. 3.1 lb. (1.39 kg)
Length ……………………………………… 8.6 in. (21.8 cm)
Width ……………………………………… 6.4 in. (16.2 cm)
Height ………………………………………… 5 in. (12.8 cm)
WARRANTY*
CHAMPION POWER EQUIPMENT 1 YEAR LIMITED WARRANTY
Warranty Qualifications
To register your product for warranty and FREE lifetime call center technical
support please visit:
https://www.championpowerequipment.com/register
To complete registration you will need to include a copy of the purchase
receipt as proof of original purchase. Proof of purchase is required for
warranty service. Please register within ten (10) days from date of purchase.
Repair/Replacement Warranty
CPE warrants to the original purchaser that the mechanical and electrical
components will be free of defects in material and workmanship for a period of
one year (parts and labor) from the original date of purchase and 90 days
(parts and labor) for commercial and industrial use. Transportation charges on
products submitted for repair or replacement under this warranty are the sole
responsibility of the purchaser. This warranty only applies to the original
purchaser and is not transferable.
Do Not Return The Unit To The Place Of Purchase
Contact CPE’s Technical Service and CPE will troubleshoot any issue via phone
or e-mail. If the problem is not corrected by this method, CPE will, at its
option, authorize evaluation, repair, or replacement of the defective part or
component at a CPE Service Center. CPE will provide you with a case number for
warranty service. Please keep it for future reference. Repairs or replacements
without prior authorization, or at an unauthorized repair facility, will not
be covered by this warranty.
Warranty Exclusions
This warranty does not cover the following repairs and equipment:
Normal Wear
Products with mechanical and electrical components need periodic parts and
service to perform well. This warranty does not cover repair when normal use
has exhausted the life of a part of the equipment as a whole.
Installation, Use, and Maintenance
This warranty will not apply to parts and/or labor if the product is deemed to
have been misused, neglected, involved in an accident, abused, loaded beyond
the product’s limits, modified, installed improperly, or connected incorrectly
to any electrical component. Normal maintenance is not covered by this
warranty and is not required to be performed at a facility or by a person
authorized by
CPE.
Other Exclusions
This warranty excludes:
– Cosmetic defects such as paint, decals, etc.
– Wear items such as filter elements, o-rings, etc.
– Accessory parts such as starting batteries, and storage covers.
– Failures due to acts of God and other force majeure events beyond the
manufacturer’s control.
– Problems caused by parts that are not original Champion Power Equipment
parts.
Limits of Implied Warranty and Consequential Damage
Champion Power Equipment disclaims any obligation to cover any loss of time,
use of this product, freight, or any incidental or consequential claim by
anyone from using this product. THIS
WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
A unit provided as an exchange will be subject to the warranty of the original unit. The length of the warranty governing the exchanged unit will remain calculated by reference to the purchase date of the original unit.
This warranty gives you certain legal rights which may change from state to state or province to province. Your state or province may also have other rights you may be entitled to that are not listed within this warranty.
Contact Information Address
Champion Power Equipment, Inc.
12039 Smith Ave.
Santa Fe Springs, CA 90670 USA
www.championpowerequipment.com
Customer Servic e
Toll-Free: 1-877-338-0999
info@championpowerequipment.com
Fax no.: 1-562-236-9429
Technical Service
Toll-Free: 1-877-338-0999
tech@championpowerequipment.com
24/7 Tech Support: 1-562-204-1188
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>