OLE 2D 270°Mini LiDAR Sensor User Guide

June 6, 2024
OLE

OLE 2D 270°Mini LiDAR Sensor User Guide

OLE 2D 270°Mini LiDAR Sensor User Guide

1.Electrical Connection

LR-1BS3/3d/5/5d contains two connectors on the back side, which are 4PIN Ethernet, 5 PIN power and I/0 connector, which is shown as below.

OLE 2D 270°Mini LiDAR Sensor User Guide - Figure 1

2. Power and I/O connector

Power supply requirement for LR-1BS3/5 is 12V~32V. The pin definitions of power and I/O connector are as follows:

OLE 2D 270°Mini LiDAR Sensor User Guide - Figure 3

3. Mechanics Connection

There are 2M3 screw holes (3mm depth) on the back for mounting of LR- 1BS3/3d/5/5d. There are also 2M3 screw holes (3mm depth) at the bottom for mounting of LiDAR. The back of the LR-1BS3/5 LiDAR has 2 connections; The bottom of the LR-1BS3d/5d LiDAR has 2 connections.

OLE 2D 270°Mini LiDAR Sensor User Guide - Figure 4

4. Communication

The LR-1BS3/3d/5/5d is connected to the computer through a standard Ethernet RJ-45 Connector, which follows the UDP protocol. The point cloud packet receiving port number is 2368, The IP setup process is shown below:

OLE 2D 270°Mini LiDAR Sensor User Guide - Figure 5

Both the LiDAR and the computer IP addresses must be set in the same subnet and conflict should be avoided. Factory setting: IP: 192.168.1.100, subnet mask: 255.255.255.0. Computer IP: 192.168.1.10 Subnet mask: 255.255.255.0. The IP settings can be modified on the configuration web page.

5. Communication Data Protocol

UDP/IP standard internet protocol. Data are in little-endian format, lower byte first Data Packet Format

OLE 2D 270°Mini LiDAR Sensor User Guide - Communication Data
Protocol

The total length of a data frame is 1240 bytes, including:
Frame header: 40 bytes
Data block: 150 x 8 1,200 bytes

OLE 2D 270°Mini LiDAR Sensor User Guide - Figure 6

OLE 2D 270°Mini LiDAR Sensor User Guide - Figure 7

6. Webserver configuration

The LR-1BS3/3d/5/5d’s parameter is configured on the webserver as follows:

  • Open the web browser Please use Chrome, Firefox, Edge and
    other standards-compliant browsers Enter the right IP Address, The sensor’s IP address comes from the factory set to its default value 192.168.1.100;

  • Select the required speed value in motor RPM: 600/900/1200/1500, corresponding to the 10/15/20/25Hz LiDAR scanning frequency;

  • Host IP: Your computer IP Address

  • Host Port: Your computer Port

  • LiDAR IP: LiDAR IP Address

  • Net Mask: Subnet mask

  • Gateway: Gateway address

OLE 2D 270°Mini LiDAR Sensor User Guide - Figure 8

7. Service and maintenance

Please visit the OLEI official website for enquiry of service and maintenance information;
Website: www.ole-systems.com
Path: Service and Support>>Service and maintenance

http://weixin.qq.com/r/SCrB2WrE2zekrS66939a

Hangzhou OLE-Systems Co., Ltd.
No. 35 Jiu Huan Road, Jiangnan District,
Hangzhou, Zhejiang, China, 310019
Tel: 86-571-81601388
Fax: 86-571-89732807
Email: tac@ole-systems.com
Web: http://www.ole-systems.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals