Godox S60 Focusing LED Light Instruction Manual

Godox S60 Focusing LED Light Instruction Manual

Foreword

Thank you for purchasing Godox product!
Focusing LED Light S60 is excellent for product shooting, photojournalistic and video recording, etc. It creates stable light resource and even illumination for photography. This light’s brightness can be precisely adjusted with easy operation.

Main Features:

• With specially designed lens to gain soft and even light effect from center to edge

• Adjustable focusing range and light brightness enable you to observe the variation of shadow’s hardness, dimension and edge contrast

• Precisely control the light and achieve more creative light effects when use in
  combination with abundant accessories

• Three ways of power supply (5V/7.4V/15V) offer great convenience, portability and wide application

Warning

• Do not disassemble or modify. Should the product break down, send the
  defective back to the authorized service center for inspection and maintenance.

• If this product overheats, it will cease operation and resume working after cooling down. This is due to the built-in over-temperature protection.

• As this product adopts make and break device, please keep it easy to be used.

• Keep dry. Do not handle with wet hands, immerse in water, or expose to rain.

• Do not place in high temperature or high humidity conditions.

• Keep out of reach of children.

• Disconnect from the power supply when it will not be used for an extended period.

Name of Body

Main Body

1. Body
2. Direction Adjusting Bracket
3. Lens
4. Accessory Latch
5. Select Dial
6. Fixing Knob
7. Thermovent
8. Power Socket
   

Controller

1. Display

2. Power Switch

3. MENU Button

4. FX Button

5. Fan Switch

6. SET Button

7. + – Select Dial

8. DMX Output Port (male)

9. DMX Output Port (female)

10. Power Input

11. Power Output

12. Battery Clip

13. Battery Release Button

14. Battery Compartment

15. Battery Base

16. Steel Cable

Included Items

• Light Body *1
  

• Controller *1
  

• Barndoor Set *1
  

• Wrench *1

• Connect Cable *1

• Power Cable *1

• Instruction Manual *1

Optional Accessory

The product can be used in combination with the following accessories sold separately, so as to achieve best photography effects.

• SA-P Projection Attachment (included a SA-01 85mm Lens)
  

• SA-01 85mm Lens

• SA-02 60mm Wide-angle Lens

• SA-03 150mm Telephoto Lens
  

• SA-05 Scrim Set

• SA-06 Iris Diaphragm

• SA-07 Framing Shutter

• SA-09 GOBO Set

• SA-10 GOBO Holder

• SA-11C (Color effects set)
  SA-11T (Color temperature adjustment set) Color Filter

• RC-A6 Remote Control

Power Supply

DC Power Supply

1. Insert the two ends of power source connect cable into the controller’s power output port and light’s power input port until a “click” can be heard.
   Pull out the connect cable: press down the PUSH button and pull out the cable simultaneously.

2. Insert the power cable’s output end into the controller’s input port. Then, rotate it rightwards to 15° until a “click” can be heard.
   Pull out the power cable: press the PUSH button on the output end of power cable and rotate it leftwards to 15°to pull out.

3. Connect power cable into the power source.
   

V-port Battery Power Supply (Optional)

Install the V-port battery onto the controller’s battery compartment. Then, power the light on to operate.

Note: please use the standard V-port battery with 14.8V standard voltage. Do not supply power with the battery whose voltage is over 16.8V

Operation

• Power switch:
  Short press the power switch, and the LED light will be lighted on. Press the button again to turn off the light.
  

• Brightness adjustment:
  In the main interface, turn the select dial to adjust brightness from 0% to 100%
  

• Light effects setting:
  In normal status, short press the FX button once to  enter the setting interface. Then, turn the select dial to choose light effects from OFF and 1 to 8.
  

Short press the FX button or SET button to exit from light effects modes and back to the main interface after settings finished.

Note: If a light effect is selected from 1 to 8, the FX icon and light effects will be displayed on the main interface. And the brightness can be adjusted. The color temperature will not be displayed.

If choose OFF, the color temperature will be displayed instead of FX icon

Silent Mode:

In normal status, short press the Fan button to turn it on or off. When turning off the fan, the LED light will enter silent mode. And the icon will be displayed and the brightness will be adjusted from 0% to 50%.
Note: the fan will be turned on by default and there is no icon appeared on the display.

Control Mode Selection

1. 2.4G Wireless Control

With 2.4G wireless system, S60 focusing LED video light has remote grouping and control function. It is recommended to purchase RC-A6 remote control (optional) to achieve wireless control. Multiple LED lights can be controlled. 32 channels and 99 IDs are available with strong anti-interference capability.

Note:

1. Please make LED light’s channel, group and ID to the same as remote control’s.
2. The wireless signals can only be received in the situation that the LED light is powered on.

CH Channel Adjustment/GR Group Adjustment/ID Value Adjustment

In main interface, short press MENU button once and turn the select dial to adjust channel, group and ID values.

In CH channel setting interface, short press SET button and the channel icon will blink. Then, turn the select dial to choose channel from 1 to 32. Press the SET button to confirm and the icon will stop blinking.

In GR channel setting interface, short press SET button and the group icon will blink. Then, turn the select dial to choose group from A to F and 0 to 9.
Press the SET button to confirm and the icon will stop blinking.

In ID channel setting interface, short press SET button and the group icon will blink. Then, turn the select dial to choose group from OFF and 1 to 99.
Press the SET button to confirm and the icon will stop blinking.

After setting all these parameters, short press SET button to confirm and back to the main interface.

Note: the LED light will auto return to the main interface if there’s no operation after 10 seconds.

Bluetooth Control

Bluetooth Code Display & RESET Function Check Bluetooth code: in main interface, short press MENU button. Then, press the select dial to switch the icons. The Bluetooth icon will be displayed after Bluetooth icon appeared.

Bluetooth reset function: in the Bluetooth code interface, long press the SET button for 2 seconds and the Bluetooth icon will blink because of resetting. And the icon will stop blinking after successfully reset. Then, short press the MENU button to return to main interface.

Note: The LED light’s Bluetooth function should be turned on. The APP can be used directly on the firstly installed device (smartphone or iPad). When change to other mobile device(smartphone or iPad), the light shall be reset before the normal connection of APP.

Scan the QR code to download the “Godox Light” smartphone APP(can be used in Android and Apple).
For more smartphone APP operations, please open the “help” in APP to gain detailed guidance.

DMX Control Mode

In main interface, short press MENU button once and turn the select dial to switch until the DMX icon is displayed. Short press the SET button and the icon will be blinking. Then, turn the select dial to set the DMX channel from 1 to 512. Adjustment in 10 values quickly or 1 value normally. Then, short press the SET button to confirm and the icon will stop blinking. Short press the MENU button to return to main interface.

DMX Parameters:

Integer
0-100% Brightness| DMX(100/255)
Integer
0-100% Brightness|
n+2| | DMX(total light effects/255)| For example: total light effects 8，DMX=160, light effects
No.=160*8/255=5

Technical Data

100% Illuminance(LUX)

(1m,darkroom) (≈)

| Spot(Central Area)| 3200
Flood(Central Area)| 40000
CRI| ≥96
TLCI| ≥97
Brightness Range| 0~100%
Channel(CH)| 32 (1 to 32)
Group (GR)| 16 (A to F/ 0 to 9)
Beam Angle| 6°-55°
Working Environment Temperature| -10~40°C
Control Method| Smartphone APP/2.4G wireless remote
control/DMX control
2.4G Wireless Transmission Distance(≈)| 50m
Dimension (≈)| Light body: 264107100mm
Controller: 26811364mm
New weight(≈)| Light body: 1.36kg
Controller: 0.94kg

• Product design and specifications are subject to change without notice.

Maintenance

This product, except consumables e.g. battery, power cable and connect cable, is supported with a one-year warranty.

Avoid sudden impacts and the product should be dedusted regularly.
Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories.
Unauthorized service will void the warranty.
If the product had failures or was wetted, do not use it until it is repaired by professionals.
Changes made to the specifications or designs may not be reflected in this manual.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

References

• GODOX Photo Equipment Co.,Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>