DROMIDA DIDC03000 1/10 Backbone 4WD RTR Rock Racer Instruction Manual

DROMIDA DIDC03000 1/10 Backbone 4WD RTR Rock Racer

NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.

Meaning of Special Language
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not attempt disassembly, use with incompatible components or augment product in any way without the approval of Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

SAFETY PRECAUTIONS AND WARNINGS

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or property of others.
This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary loss of control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.

• Never operate your model with low transmitter batteries.
• Always operate your model in open spaces away from full-size vehicles, traffic and people.
• Never operate the model in the street or in populated areas for any reason.
• Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.) you use.
• Keep all chemicals, small parts and anything electrical out of the reach of children.
• Never lick or place any portion of the model in your mouth as it could cause serious injury or even death.
• Exercise caution when using tools and sharp instruments.
• Take care during maintenance as some parts may have sharp edges.
• Immediately after using your model, do NOT touch equipment such as the motor, electronic speed control and battery, because they generate high temperatures. You may burn yourself seriously touching them.
• Do not put fingers or any objects inside rotating and moving parts, as this may cause damage or serious injury.
• Always turn on your transmitter before you turn on the receiver in the car.
• Always turn off the receiver before turning your transmitter off.
• Keep the wheels of the model off the ground when checking the operation of the radio equipment.

NIMH CHARGING WARNINGS

WARNING: Failure to exercise caution while using this product and comply with the following warnings could result in product malfunction, electrical issues, excessive heat, FIRE, and ultimately injury and property damage.

• NEVER CHARGE BATTERIES OVERNIGHT.
• NEVER LEAVE CHARGING BATTERIES UNATTENDED.
• Read all safety precautions and literature prior to use of this product.
• Never allow children under 14 years of age to charge battery packs.
• Never attempt to charge dead or damaged batteries.
• Never charge a battery if the cable has been pinched or shorted.
• Never allow batteries or charger to come into contact with moisture at any time.
• Never charge batteries in extremely hot or cold places (recommended between 50­80°F (10­26°C)) or place in direct sunlight.
• Always use only Ni-MH rechargeable batteries. This charger cannot charge batteries such as “heavy duty,” “alkaline battery,” “lithium,” or “mercury battery.”
• Always connect to the charger correctly.
• Always disconnect the battery and charger after charging and let them cool between charges.
• Always inspect the battery before charging.
• Always terminate all processes and contact Horizon Hobby if the product malfunctions.
• Always make sure you know the specifications of the battery to be charged or discharged to ensure it meets the requirements of this charger.
• Always constantly monitor the temperature of the battery pack while charging.
• Always end the charging process if the charger or battery becomes hot to the touch or starts to change form during the charge process.

VEHICLE AND RADIO PARTS

1. Steering Wheel Controls direction (left/right) of the model

2. Throttle Trigger Controls speed and direction (forward/brake/reverse) of the model

3. On/Off Switch Turns the power on/off

4. TH Trim Adjusts the throttle trim/dual rates

5. ST Trim Adjusts the steering trim/dual rates

6. CH 3

7. Indicator Lights
   Solid Blue Light–Indicates radio connectivity and adequate battery power Flashing Blue Light–Indicates the battery voltage is critically low. Replace batteries

8. REV Reverses the steering wheel and throttle functions

9. Antenna Transmits the signal to the model

BATTERIES

Radio
This transmitter requires 4 AAA batteries.

1. Remove the battery cover from the transmitter.
2. Install the batteries as shown.
3. Install the battery cover.

| CAUTION: If using rechargeable batteries, charge only rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property.
---|---
| CAUTION: Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries according to national regulations.
---|---

Vehicle

1. Switch off the vehicle and remove the battery.
2. Carefully connect the battery to the charger.
3. Plug the charger into an AC wall outlet.
4. The charging process takes approximately 2 hours. Unplug the battery when charge is complete.

| WARNING: Never leave charging batteries unattended. Only use the included NiMH charger to charge the included NiMH battery. Never charge a LiPo battery with a NiMH charger.
---|---

DRIVING THE VEHICLE

1. Install the battery into the vehicle and connect the battery.

2. Secure the battery straps to the post using using clips.

3. Switch the radio on.

4. Switch the vehicle on.

• To slowly drive forward, pull the trigger slightly. To drive faster, pull the trigger further.
• To brake, push the trigger. To drive in reverse, push again.
• During a crash, release the trigger.
• To turn, rotate the wheel to the left or right.
• Adjust the steering trim if the car doesn’t track straight (see below).
• When the vehicle battery becomes low, the vehicle will start to slow down.
• Allow the battery to cool before recharging.
• Make sure to turn both the vehicle and the radio off after each use.
• ALWAYS unplug the battery after each use.

DUAL RATES

The transmitter allows you to adjust steering and throttle dual rates.

Steering Dual Rate

1. Power ON the transmitter.
2. Power ON the model.
3. Apply either the left or right steering input on the transmitter and hold that position.
4. To add or remove steering throw input, continue to hold steering input while adjusting the dual rate using the (+) or (-) ST button.

Throttle Dual Rate

5. Turn ON the transmitter.
6. Turn ON the model.
7. Apply either forward or reverse throttle input on the transmitter and hold that position.
8. To add or remove throttle input, continue to hold throttle input while adjusting the dual rate using the (+) or (-) TH button.

NOTICE: Do not adjust the throttle dual rate while the model is powered on and resting on a stand. Adjusting the throttle dual rate may power the motor, which could cause damage to property or personal injury.

DRIVING TIPS

• Always release the throttle trigger right away following a crash to prevent damaging the electronics.
• The vehicle should be operated in an open space with no people or animals nearby.

BINDING PROCEDURE

Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. The transmitter and receiver are bound at the factory. If you need to rebind, follow the instructions below:

1. Connect a fully charged battery to the ESC.
2. Power on the ESC
3. Press the bind button on the receiver. The red LED will flash, indicating the receiver is in bind mode.
4. Power ON the transmitter. The receiver’s red LED will turn solid when the bind is successful.
5. Power OFF the /ESC to save the settings.
6. Power OFF the transmitter.
7. You must rebind when binding the receiver to a different transmitter.

NOTICE: Do not attempt to bind the transmitter and receiver if there are other compatible transmitters in bind mode within 400 feet. Doing so may result in unexpected binding.

This parts list shows the key number, part description, and stock number for the replacement parts sets. When more than one stock number is listed, that part is available in multiple replacement parts sets.

# Item Description Part Number
1 Diff Gear Box (1): Backbone …………………. DIDC0795
2 Diff Drive Spur Gear(2):Backbone …………. DIDC0811
3 Rear Axle Housing:Backbone ……………….. DIDC0877
4 Rear Axle Cover:Backbone …………………… DIDC0878
5 Axle Adaptor (2):Backbone…………………… DIDC0879
6 RR HLDR RR SHK SPRT (2):Backbone ……. DIDC0880
7 Rear Shock Spring (2):Backbone ………….. DIDC0881
8 Rear Link Set (2):Backbone …………………. DIDC0882
9 Upper Plate:Backbone ………………………… DIDC0883
10 Rear CNTR CVD FR Half:Backbone ……….. DIDC0902
11 Preassembled Tires(2):Backbone …………. DIDC0904
12 Rear Diff Shaft:Backbone ……………………. DIDC0907
12 R SHCK Shaft & Piston STS:Backbone …… DIDC0909
14 Black Flanged Locknut, M4 x 0.7mm (4) TLR236009
15 Button Head Screws, M3 x 8mm (10) …….. TLR5902
16 Flathead Screws, M3 x 10mm (10) ……….. TLR5962
17 5x11x4mm Bearing (2) ……………………….. AXIC0221
18 Rear Drive Shaft Short: Backbone …………. DIDC0886
19 Rear Drive Shaft Long: Backbone …………… DIDC0887
20 Wheel Hub Hexes (4): Backbone …………… DIDC0828
21 PIN 10X2 (6): Backbone ………………………. DIDC0843
22 10 x 15 x 4mm Bearing (4) ……………….. LOS237001
23 Rear Link Holder: Backbone ………………… DIDC0873

We try very hard to have accurate and up-to-date information in this document. Any errors are unintentional.

This parts list shows the key number, part description, and stock number for the replacement parts sets. When more than one stock number is listed, that part is available in multiple replacement parts sets.

# Item           Description         Part Number
1 Rear Shock Tower (2): Backbone ………….. DIDC0796
2 Front Shock Tower: Backbone ……………… DIDC0797
9 FR Lower Susp Arm St(2): Backbone …….. DIDC0804
10 Steer Knuckle ArmSts(2): Backbone ……… DIDC0805
11 Uprights (2):Backbone ………………………… DIDC0806
12 Front CVD (2): Backbone ……………………… DIDC0807
13 Front Susp Holder (2): Backbone ………….. DIDC0808
14 Bumper Set: Backbone ……………………….. DIDC0809
15 Gearbox Housing Set(2): Backbone……….. DIDC0810
16 Diff Drive Spur Gear(2):Backbone …………. DIDC0811
17 Differential Case (2): Backbone ……………. DIDC0812
18 Diff Drive Spur Gear(2):Backbone …………. DIDC0813
19 Diff Drive Gear (2): Backbone ……………….. DIDC0814
24 Diff Bevel Gear S. (4): Backbone …………… DIDC0815
25 Diff Bevel Gear B (4): Backbone ……………. DIDC0816
26 Diff Pin(2): Backbone ………………………….. DIDC0817
27 Washer (6): Backbone …………………………. DIDC0818
28 Diff Drive Cups: Backbone …………………… DIDC0819
29 Center Coupler (3): Backbone ………………. DIDC0820
30 Body Post (2): Backbone ……………………… DIDC0821
31 Servo Saver Set: Backbone …………………. DIDC0822
32 Servo Saver Post (2): Backbone ……………. DIDC0823
33 Steering Ackerman: Backbone……………… DIDC0824
34 FR Upper Susp Arms (2): Backbone ………. DIDC0825
35 Steering Arm (2): Backbone DIDC0826
36 Servo Linkage: Backbone ……………………. DIDC0827
37 Wheel Hub Hexes (4): Backbone …………… DIDC0828
40 Metal Bushing 15X10X4 (6): Backbone ….. DIDC0831
41 Metal Bushing 8X5X2.5 (6): Backbone …… DIDC0832
42 M0.6 Pinion Gear 17T: Backbone ………….. DIDC0833
43 Shock Ball end (6): Backbone ………………. DIDC0834
44 Servo Link Ball END(6): Backbone ……….. DIDC0835
45 Steer Link Ball L End(6): Backbone ……….. DIDC0836
46 Ball A (6): Backbone ……………………………. DIDC0837
47 Ball B (6): Backbone ……………………………. DIDC0838
48 Ball C (6): Backbone ……………………………. DIDC0839
49 Shock O-ring Lower (6): Backbone ……….. DIDC0840
50 Diff O-ring Seal (6): Backbone ……………… DIDC08b41
51 Shock Seal Cover (4): Backbone …………… DIDC0842
52 PIN 10X2 (6): Backbone ………………………. DIDC0843
53 Hinge Pins (2): Backbone …………………….. DIDC0844
55 Metal Bushing 10X5X4 (6): Backbone ……. DIDC0845
56 Bearings 8X5X2.5 (6): Backbone ………….. DIDC0846
58 E CLIP (4): Backbone …………………………… DIDC0847
59 E CLIP (6): Backbone …………………………… DIDC0848
60 M2x 10 STP Hex Screw (6): Backbone …… DIDC0849
61 M3x6 RND STP Hex Screw(6): Backbone .. DIDC0850
62 M3x6 Ring STP Screw (6): Backbone …….. DIDC0866
62 M3x6 Ring STP Screw (6): Backbone …….. DIDC0866
63 Roll Cage Top Frame: Backbone …………… DIDC0869
64 Roll Cage Side Frame(2): Backbone ………. DIDC0870,
65 Roll Cage Front: Backbone DIDC0871
66 Roll Cage Rear Plate: Backbone……………. DIDC0872
67 Rear Link Holder: Backbone ………………… DIDC0873
68 RR Central CVD RR Half: Backbone ……….. DIDC0874
69 Spare Wheel Support: Backbone ………….. DIDC0875
70 Roll Cage Window Frame: Backbone DIDC0876
71 FR CNTR Drive Shaft: Backbone …………… DIDC0884
72 RX Cover: Backbone ……………………………. DIDC0885
73 FR HLDR RR SHK SPRT (2): Backbone DIDC0888
74 Sway Bar: Backbone …………………………… DIDC0889
75 Battery Case Holder (2): Backbone ……….. DIDC0890
76 Main Frame(2): Backbone ……………………. DIDC0891
77 RR SHKS Low SPT Rod(2): Backbone ……… DIDC0892
78 Sway Bar Pull Rod Upper: Backbone ………. DIDC0894
79 Sway Bar Pull Rod Lower: Backbone ………. DIDC0895
80 Central Drive Shaft: Backbone ………………. DIDC0897
81 Motor Mount For 17T: Backbone ……………. DIDC0898
82 CNTR Trans Cover Upper: Backbone ……….. DIDC0899
83 CNTR Trans Cover Lower: Backbone ……….. DIDC0900
84 Driver Helmet (2): Backbone …………………. DIDC0905
85 DRVR Blister ST W/Decal: Backbone ………. DIDC0906
86 Battery Strap (2):Backbone …………………… DIDC0938
87 Chassis, Aluminum: Backbone ………………. DIDC0950
88 Motor Rock Rider, 21T:Backbone ……………. DIDC1083
89 62T Steel Spur Gear:Backbone ……………… DIDC1287
90 3kg Servo: Backbone …………………………… DIDC1288
91 7.2V 1800MAH 6CNiMH Flat EC3 ………. DYNB2050EC
92 3Ch 2.4Ghz Surface Tx ………………………… HRZ00001
93 2.4Ghz Receiver WP 3-Channel …………….. HRZ00006
94 M3 x 14mm Flat Head Screw (10) ………. AXI235178
95 Set Screw M3x10mm (10) …………………… AXIC0184
96 5x11x4mm Bearing (2) ……………………….. AXIC0221
97 Nylong Locking Hex Nut M3 Black (10) ….. AXIC1053
98 Cap Head Screws, M3 x 30mm (10)……. LOS235004
99 Set Screw M3 x 3MM (10) ………………… LOS235018
100 10 x 15 x 4mm Bearing (4) ……………….. LOS237001
101 Cap Head Screws, M3 x 16mm (10)……. LOS255009
102 Flat Head Screws, M3 x 18mm (10) ……. TLR235005
103 Black Flanged Locknut, M4 x 0.7mm (4) TLR236009
104 Button Head Screws, M3 x 8mm (10) …….. TLR5902
105 Button Head Screws, M3 x 10mm (10) …… TLR5903
106 Button Head Screws, M3 x 12mm (10) …… TLR5904
107 Button Head Screws, M3 x 20mm (10) …….TLR5911
108 Flathead Screws, M3 x 8mm (10) …………… TLR5961
109 Flathead Screws, M3 x 10mm (10) ……….. TLR5962
110 Flathead Screws, M3 x 12mm (10) ………… TLR5963
111 Flathead Screws, M3 x 16mm (10) ………… TLR5964
112 5x10x4mm Bearing (2) ……………………….. AXIC0218
113 Cap Head Screws, M3 x 10mm (10)………..  TLR5910
114 Fr. Shock Complete (2): Backbone ………… DIDC0794

We try very hard to have accurate and up-to-date information in this document. Any errors are unintentional.

WARRANTY

What this Warranty Covers –Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at date of purchase.

What is Not Covered –This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations or (vii) use that violates any applicable laws, rules, or regulations. OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy- -Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability- -HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.

Law- -These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services –Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.

Inspection or Services –If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com/content /servicecenter_render-service-center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a Li-Po battery, please contact the appropriate Horizon Product Support office.

Warranty Requirements- -For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.

Non-Warranty Service –Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non- warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby.com/content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.

FCC INFORMATION

FCC ID: 2ARE7-91803 Supplier’s Declaration of Conformity
Dromida 1/10 Backbone Rock Racer RTR (DIDC03000)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC 2904 Research Rd., Champaign, IL 61822
Email: compliance@horizonhobby.com
Web: www.HorizonHobby.com

WARRANTY AND SERVICE CONTACT INFORMATION

Country of Purchase

|

Horizon Hobby

|

Contact Information

|

Address

---|---|---|---

United States of America

|

Horizon Service Center (Repairs and Repair Requests)

|

www.servicecenter.horizonhobby.com/ReuqestFrom/

productsupport@horizonhobby.com

877-504-0233

| 2904 ResearchRd Champaign,Illinois,61822 USA

Horizon Product Support (Product Technical Assistance)

Sales

|

websales@horizonhobby.com

800-338-4639

©2020 Horizon Hobby, LLC. Dromida, the Dromida logo, Backbone and the Horizon Hobby logo are trademarks or registered trademarks of Horizon
Hobby, LLC. All other trademarks, service marks and logos are property of their respective owners.

www.dromida.com

References

• Dromida Ready to Run RC Vehicles and Quadcopters
• RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
• Horizon Hobby Service Center
• RC Cars, RC Trucks, RC Airplanes, Model Trains, and Slot Cars at Tower Hobbies
• RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
• Horizon Hobby Service Center

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>